HP DesignJet 800ps A1 User Manual

							Media & Ink Introduction Front PanelOther Printer 
OptionsIndex  Solutions
Care of the Printer


Installing Expansion 
CardsSpecifications Ordering Accessories Glossary
Cleaning the PrinterWARNING:To avoid an electric shock, make sure that the printer is switched OFF and disconnected from the
mains supply before you clean it. Do not let water get inside the printer.
CAUTION:Do not use abrasive cleaners on the printer.NOTE:
Any maintenance or repairs beyond those described in this chapter should be done by a qualified
service technician.
Cleaning the Printer ExteriorClean the outside of the printer as required with a damp sponge or a soft cloth and a mild household cleaner such as 
non-abrasive liquid soap.
 
						

							Media & Ink Introduction Front PanelOther Printer 
OptionsIndex  Solutions
Care of the Printer


Installing Expansion 
CardsSpecifications Ordering Accessories Glossary
Storing and Moving Your PrinterIf you need to move your printer or store it for an extended period of time, you need to prepare your printer 
properly to avoid possible damage to the printer. To prepare your printer, follow the instructions given below:CAUTION:It is important that you do not remove the Ink Cartridges and Printheads before moving or storing
the printer.
1. Switch the power off at the On/Off power switch on the front of the printer.
2. Disconnect any cables connected to the printer; parallel interface, LAN connection.
3. Repack the printer in its original packaging. Refer to Assembly/Repacking Instructions booklet supplied with the 
printer for details.
4. If you have to move your printer you will need the original packaging. If necessary you can order a kit of the 
packaging materials. Contact HP suppor t and they will supply it to you. If necessary they will repackage the printer 
for you.
 
						

							Care of the PrinterInstalling Expansion 
Cards


Specifications Ordering Accessories Glossary
Media & Ink Introduction Front PanelOther Printer 
OptionsIndex  Solutions
Installing Expansion CardsThe following options are available for your 
HP DesignJet 800PS printer:
Network Card Installation
 
						

							Care of the PrinterInstalling Expansion 
Cards


Specifications Ordering Accessories Glossary
Media & Ink Introduction Front PanelOther Printer 
OptionsIndex  Solutions
Network Card InstallationAn HP JetDirect Network Card is installed in your printer when you buy it. If you wish to use a different network card 
install it using the following procedure.
HP JetDirect Network Card Installation
1. Before installing a card, switch off the printer 
and unplug it from the mains electricity supply.
2. Carefully remove the plastic cover from the 
left-hand back of the printer by unclipping it. 
This cover gives access to the two slots for an 
Accessory card and a LAN card.
Press in the thumb-tab on the side fur-
thest from the edge that has the cable-
hole.
Ease the cover out in the direction of the 
embossed arrow, pivoting it by the hinge 
clips on the side that has the edge cable-
hole.
Continued …
 
						

							Care of the PrinterInstalling Expansion 
Cards


Specifications Ordering Accessories Glossary
Media & Ink Introduction Front PanelOther Printer 
OptionsIndex  Solutions
3. Remove the cover completely Inside the 
compartment there are two slots for a LAN 
card or an Accessor y card.
You can use either slot for either card, but we 
recommend putting a LAN card on the left 
(nearer to the front of the printer) and an 
Accessory card on the right. In this way the 
cable from the LAN card can easily pass 
through the slot in the door.
4. To insert a LAN card (or an Accessory card), 
remove the metal cover from the appropriate 
slot by unscrewing its two screws. You can 
use a screwdriver or do it manually.
5. When you have inserted the card, screw it 
into place, 
using its two screws (at the top 
and bottom of the card). Again, this can 
be done with a screwdriver or manually.
Previous …
Continued …
HP JetDirect Network Card Installation (Continued)
 
						

							Care of the PrinterInstalling Expansion 
Cards


Specifications Ordering Accessories Glossary
Media & Ink Introduction Front PanelOther Printer 
OptionsIndex  Solutions
6. Insert the LAN cable into the LAN card. It is 
simply pushed into place and clicks when 
locked.
7. Carefully replace the plastic cover by clipping 
it back into place:
Put the two hinge clips on the side that 
has the edge cable-hole into their slots.
Swivel the cover in the direction opposite 
to the embossed arrow and clip the other 
two tabs on the opposite side into their 
slots. Ensure that the LAN cable passes 
correctly through the edge cable-hole 
(shown by the yellow arrow).
Take care to carefully route the LAN cable 
so it does not interfere with the spindle or 
roll.
8. Once you have completed the physical installation of the card you will have to configure it for 
you LAN, see Setting up the I/O Card
.
Previous …
HP JetDirect Network Card Installation (Continued)
 
						

							Care of the PrinterInstalling Expansion 
Cards


Specifications Ordering Accessories Glossary
Media & Ink Introduction Front PanelOther Printer 
OptionsIndex  Solutions
HP-GL2 Accessory Card InstallationNot available for your printer model. 
 
						

							Care of the PrinterInstalling Expansion 
CardsSpecifications


Ordering Accessories Glossary
Media & Ink Introduction Front PanelOther Printer 
OptionsIndex  Solutions
Specifications
Functional SpecificationsMemory SpecificationsPrinter Power SpecificationsEcological SpecificationsEnviromental SpecificationsAcoustic SpecificationsConnection Specifications
 
						

							Care of the PrinterInstalling Expansion 
CardsSpecifications


Ordering Accessories Glossary
Media & Ink Introduction Front PanelOther Printer 
OptionsIndex  Solutions
Functional Specifications
HP DesignJet 800PS Functional Specifications
Functional Specifications
HP Ink 
Supplies 
Supplies
Four colors: cyan, magenta, yellow and black. 
Printheads:
600 dpi, 36 kHz (Cyan, Magenta, Yellow).
36 kHz (Black).
Ink Car tridges contents:Cyan
69 ml Magenta
Ye l l o w
Black
Pap er s ize s Width (carriage axis)
 Length (paper axis)
 Minimum 
Maximum
 Minimum 
Maximum 
Roll - D/A1 size
 
printer
140 mm
5.5 inches625 mm
25 inches
1000 mm
40 inches
100 mm
4 inches 
roll external
diameter Roll - A0+/
E+ size
 printer1071.8 mm
42.2 inches
Sheet -D/
A1 size
 printer625 mm
25 inches
140 mm
5.5 inches
1897 mm
74.7 inches
Sheet -A0+/
E+ size
 printer1071.8 mm
42.2 inches
More …
 
						

							Care of the PrinterInstalling Expansion 
CardsSpecifications


Ordering Accessories Glossary
Media & Ink Introduction Front PanelOther Printer 
OptionsIndex  Solutions
HP Supported Media
a
HP Bright White Inkjet Paper (Bond)
HP Vellum
HP Natural Tracing Paper
HP Coated Paper
HP Heavyweight Coated Paper
HP Matte film
HP High-Gloss Photo Paper
HP Semi-Gloss Photo Paper
HP Paper-Based Semi-Gloss
HP Clear film
HP Translucent bond
HP Studio Canvas
HP Satin Poster Paper
HP Banners with Tyvek®
HP Colorfast Adhesive Vinyl
Previous …
More …
HP DesignJet 800PS Functional Specifications (Continued)
Functional Specifications