HP Color LaserJet CP6015xh User Manual

Install memory
You can install more memory for the product by adding a dual inline memory module (DIMM).
CAUTION:Static electricity can damage DIMMs. When handling DIMMs, either wear an antistatic
wrist strap, or frequently touch the surface of the DIMM antistatic package and then touch bare metal
on the product.
Install DDR memory DIMMs
1.Turn the product off.
2.Disconnect all power and interface cables.
ENWWReplace supplies 157
 

3.Locate the black formatter pressure release tabs on the formatter board in the rear of the product.
4.Gently press the black tabs toward each other.
5.Gently pull on the black tabs to pull the formatter board from the product. Place the formatter board
on a clean, flat, grounded surface.
158 Chapter 11   Manage and maintain the product ENWW
 

6.To replace a DIMM that is currently installed, spread the latches apart on each side of the DIMM
slot, lift the DIMM up at an angle, and pull it out. If you are adding a DIMM, use the other slot
provided.
XOXOXOXOXOXO
XOXOXOXOXOXO
XOXOXOXOXO
XOXOXOXOXO
XOXOXO
XOXO
XOXOXOXOXO
XOXOXOXOXOXO
XOXOXOXOXOXOXOXO
XOXOXO
XOXOXO
XOXOXO
XOXOXO
XOXOXO
XOXOXO
XOXOXO
XOXOXOXOXOXO
XOXOXOXOXOXOXOXOXOXO
XOXOXOXOXOXO
7.Remove the new DIMM from the antistatic package. Locate the alignment notch on the bottom
edge of the...

10.Align the formatter board in the tracks at the bottom of the slot, and then slide the board back into
the product.
NOTE:To prevent damage to the formatter board, ensure the formatter board is aligned in the
tracks.
11.Reconnect the power cable and interface cables, and turn the product on.
12.To enable the new memory, see the following section.
Enable memory for Windows
1.Windows XP and Windows Server 2003 (using the default Start menu view): Click Start, click
Settings, and then click Printers and...

5.Next to Printer Memory, select the total amount of memory that is installed.
6.Click OK.
Install an HP Jetdirect or EIO print server card or EIO hard disk
This product is equipped with an external I/O (EIO) slot. You can install an additional HP Jetdirect print
server card in the available EIO slot.
1.Turn the product off.
2.Disconnect all power and interface cables.
ENWWReplace supplies 161
 

3.Locate an open EIO slot. Loosen and remove the two retaining screws holding the cover for the
EIO slot, and then remove the cover. You will not need these screws and the cover again. They
can be discarded.
4.Firmly insert the HP Jetdirect print server card into the EIO slot.
5.Insert and tighten the retaining screws that came with the print server card.
162 Chapter 11   Manage and maintain the product ENWW
 

6.Reconnect the power cable and remaining interface cables, and turn the product on.
7.Print a configuration page. An HP Jetdirect configuration page that contains network configuration
and status information should also print.
If it does not print, turn the product off, and then uninstall and reinstall the print server card to ensure
that it is completely seated in the slot.
8.Perform one of these steps:
●Choose the correct port. See the computer or operating system documentation for
instructions....

2.Push up to on the staple cartridge to remove it from the booklet maker or stapler/stacker.
3.Insert the replacement staple cartridge unit into the stapler unit.
4.Push the staple cartridge unit into the stapler unit until it clicks into position.
5.Close the front door.
164 Chapter 11   Manage and maintain the product ENWW
 

Replace saddle stitch staple cartridges in the booklet maker
1.Open the front door of the booklet maker.
2.Grasp the blue handle and pull the staple carriage out of the booklet maker.
3.Grasp the small blue handle on the staple cartridge unit and pull it toward you, then swing the staple
cartridge unit into an upright position.
2
1
4.Grasp the edges of each staple cartridge and pull up firmly to remove the staple cartridges from
the staple cartridge unit.
ENWWReplace supplies 165
 

5.Unpack the new cartridges and remove the plastic packing lock from each one.
6.Hold the new cartridges so that the arrows on the cartridges align with the arrows on the staple
cartridge unit and insert them into the unit.
7.Pull the handle of the staple cartridge unit toward you and rotate it downward to its original position.
Lock it into position by pushing in the handle.
1
2
8.Push the staple carriage back into the booklet maker finisher.
166 Chapter 11   Manage and maintain the product ENWW