Hitachi F7000 Instruction Manual

3.3  Defining Your Samples 
3 - 16 
When “Use sample table” is selected in Analysis Method, samples must 
be defined in the following procedure before measurement.   
Open the monitor window and click the 
 button.  
When the Sample Table window in Fig. 3-11 appears, enter the sample 
name and comment for each sample.   
 
1 For creating a sample table newly, make entry for Number of 
Samples and click the Update button.    For instance, if there are 
five samples, enter “5” for Number of Samples and...

3.3.2 
3 - 17 
 
 
Fig. 3-12 
 
 
4 Make entries for Sample and Comments of each sample.     
The sample names entered here appear on the monitor window.   
Maximum number of characters to be entered (half-size)   
Sample : 40 characters  
Comment :  255 characters  
 
Next, you must enter a file name for automatic saving after 
measurement.  
When you click a File Name column, the [...] button appears as 
shown in Fig. 3-13.    Click this button.    Upon opening of the 
window shown in Fig. 3-14,...

3.3  Defining Your Samples 
3 - 18 
 
 
 
Fig. 3-14   
 
 
5 After entries, check them and then click the OK button.   
6 Load button   
Used for reading out the existing sample table.   
Clicking the Load button displays the file opening dialog.   
 
 
 
Fig. 3-15    File Opening Dialog 
 
 
Select a sample table and click the Open button.  The specified 
sample table will be read out.   
  

3.3.2 
3 - 19 
7 Save button   
The contents of change can be saved by overwriting.    In case of a 
new generation, the Save As dialog will open.   
8 Save As button   
Used for saving the sample table with a name newly given.   
Click this button, and the Save As dialog will open.   
 
 
 
Fig. 3-16    Save As Dialog 
 
 
Select a saving location and enter a file name.    Then, click the 
Save button.   
  

3.4  Conducting Measurement 
3 - 20 
3.4  Conducting Measurement  
 
(1)  When “Use sample table” is not selected in Analysis Method, you 
should click the 
  button and make sure that a sample has 
already been defined.   
 
(2)  Set a sample and click 
 (measurement) button.  
Measurement starts and a spectrum is displayed.   
For halting the measurement midway, click the 
 (stop) 
button.   
 
(3)  Upon completion of the measurement, the measured data will be 
saved automatically at the specified...

3.4.2 
3 - 21 
(1) Click the   button and make sure a sample has already been 
defined.  
 
(2)  Set a sample and click the 
  button to start measurement.   
 
(3)  Upon start of measurement, the window shown in Fig. 3-18 
appears.  Click Yes.  
 
 
 
Fig. 3-18 
 
 
(4)  A dialog box opens as shown below.   
 
 
 
Fig. 3-19 
 
 
Click OK.    Measurement starts and a spectrum is displayed.   
For halting the measurement midway, click the 
 (stop) 
button.  
Measure all the samples set in the sample table...

3.4  Conducting Measurement 
3 - 22 
(5)  Upon completion of the measurement, the measured data will be 
saved automatically at the specified saving location using the 
specified file name.    Opening the saved data file will display the 
data processing window as shown in Fig. 3-20.    This figure 
shows a spectrum and the result of rate calculation.    Peak table 
can be displayed, but both the result of rate calculation and the 
peak table cannot be displayed simultaneously.     
Simultaneous display...

3.4.3 
3 - 23 
(1)  Put a check mark for ‘Stopped Flow’ at the Instrument tab in the 
Analysis Method window.    At the General tab in this window, 
remove a check mark from “Use sample table.”   
 
(2) Click the 
  button to make sure a sample has already been 
defined.  
 
(3) Click the 
  (measurement) button to start measurement.   
 
(4)  When measurement starts, the window shown in 3-21 appears to 
await an external start signal.     
 
 
 
Fig. 3-21  Stopped Flow Measurement Window   
(external...

3.4  Conducting Measurement 
3 - 24 
(5)  On arrival of the external signal, measurement starts and a 
spectrum is drawn in the window.   
 
 
 
Fig. 3-22    Stopped Flow Measurement Window   
 
 
For stopping the measurement halfway, click the 
 (stop) 
button.  
 
(6)  Upon completion of the measurement, the measured data will be 
saved automatically at the specified saving location using the 
specified file name when auto saving is selected.     
If auto saving is not selected, select the “Save As”...

3.4.3 
3 - 25 
NOTICE:  1.  The data measured under the following conditions will 
be saved automatically in Program Files\FL 
Solutions\Data.  (Example:  C:Program Files\FL 
Solutions\Data)  
(1)  Measurement was carried out using a sample table 
with no file name specified in the File Name 
column.  
(2)  Measurement was carried out with “Auto File” 
specified and a file name unspecified, avoiding use 
of a sample table.   
2.  The data measured under the following conditions will 
be saved...