Hitachi F7000 Instruction Manual

2.2    Creating an Analysis Method 
2 - 14 
Select the Report tab, and the window in Fig. 2-9 will appear.   
For the settable range of each parameter, refer to Appendix G.   
 
 
 
Fig. 2-9  Report Tab 
 
 
This window is used to select a printout method and items of 
measurement results.   
 
1 Output  
• Print Report   
Data of the specified items will be printed in a report.     
For printing method, refer to 2.6.   
• Use Microsoft(R) Excel   
Data of the specified items will be transferred to...

2.2.5 
2 - 15 
2 Orientation  
Selectable when Print Report is chosen for Output.   
Select a printing orientation.    Either Portrait or Landscape 
orientation is selectable.    When the Landscape orientation is 
selected, date and method can be printed.   
3 Print items (printable/transferable items) 
• Include date   
• Include method   
• Include graph   
• Include data listing   
◊ Constant  
Data will be printed at fixed intervals between 2 wavelength 
points.    Make entries for Data interval,...

2.3  Defining Your Samples 
2 - 16 
2.3  Defining Your Samples  
 
When “Use sample table” is not selected in Analysis Method, a sample 
must be defined in the following procedure before measurement.   
 
(1) Click the 
  button.    The window in Fig. 2-10 will appear.   
 
 
 
Fig. 2-10   
 
 
(2)  Make entries for Sample name and Comment.   
Maximum number of enterable characters (half-size)   
 
Sample name :  40 characters   
Comment : 255 characters  
 
For automatic saving, put a check mark in the...

2.3.2 
2 - 17 
When you put a check mark at the head of “Auto JCAMP-DX file,” 
“Auto Text file” and “Auto Meta file” after turning on “Auto File,” 
wavelength scan data can be saved automatically in the following 
file formats as soon as this data is automatically saved.   
•  JCAMP-DX file (*.dx)   
•  ASCII text file (*.txt)   
•  Graph meta file (*.wmf)   
The data will be saved in the file name entered for “File name.”   
 
(3)  After completion of setting, click OK.  
 
 
When “Use sample table” is...

2.3  Defining Your Samples 
2 - 18 
2 For adding a row at the end of sample table, click the Insert button.   
3 To delete an unnecessary row, click its row No. to make it active as 
shown in Fig. 2-12.    Then, click the Delete button.   
 
 
 
Fig. 2-12   
 
 
4 Make entries for Sample and Comments of each sample.     
The sample names entered here appear on the monitor window.   
Maximum number of characters to be entered (half-size)   
Sample : 40 characters  
Comment :  255 characters  
 
Next, you...

2.3.2 
2 - 19 
 
 
 
Fig. 2-13   
 
 
 
 
Fig. 2-14   
 
 
5 After entries, check them and then click the OK button.   
6 Load button   
Used for reading out the existing sample table.   
Clicking the Load button displays the file opening dialog.   
4
5
67 8  

2.3  Defining Your Samples 
2 - 20 
 
 
 
Fig. 2-15    File Opening Dialog 
 
 
Select a sample table and click the Open button.  The specified 
sample table will be read out.   
 
7 Save button   
The contents of change can be saved by overwriting.    In case of a 
new generation, the Save As dialog will open.   
8 Save As button   
Used for saving the sample table with a name newly given.   
Click this button, and the Save As dialog will open.   
 
 
 
Fig. 2-16    Save As Dialog 
 
 
Select a saving...

2.4 
2 - 21 
2.4  Prescan  
 
Select the Auto Pre-scan command from the Spectrophotometer menu 
or click the 
 (pre-scan) button.  
This function executes high-speed scan under the set measuring 
conditions, detects the peak wavelength and moves the system to that 
wavelength.    Also, the upper limit photometric value on the Y-axis scale 
is automatically set so that the peak-wavelength value becomes 
approximately 70% of that upper limit value.    In this case, the lower 
limit photometric value on the...

2.5  Conducting Measurement 
2 - 22 
2.5  Conducting Measurement  
 
(1) Click the 
  button and make sure a sample has already been 
defined.  
 
(2)  Set a sample and click 
 (pre-scan) button.  
 
(3)  After completion of pre-scan, click the 
 button.  
Measurement starts and a spectrum is displayed.   
For halting the measurement midway, click the 
 (stop) button.  
 
(4)  Upon completion of the measurement, the measured data will be 
saved automatically at the specified saving location using the...

2.5.2 
2 - 23 
(1) Click the   button and make sure a sample has already been 
defined.  
 
(2)  Set a sample and click 
 (pre-scan) button.  
 
(3)  After completion of pre-scan, click the 
 button.  The window 
shown in Fig. 2-18 appears.    Click Yes.  
 
 
 
Fig. 2-18 
 
 
(4)  A dialog box opens as shown below.   
 
 
 
Fig. 2-19 
 
 
Click OK.  Measurement starts.  
For halting the measurement midway, click the 
 (stop) 
button.   
Measure all the samples set in the sample table according to the...