GTE Omni Si Database Technical Practices Manual

TL-130400-1001Table 17.3AEntry Fields for Record Code AP (Continued)COMMENTS
uggested value =8 = escape from the data transfer mode
1 for terminals_21 = send an interrupt plus an indication of a
break message to PAD and discard output to
O-31= numberofIndicate how many padding characters are to
be inserted after a carriage return.
-Printing devices need sufficient time for the
suggested
value =mechanism to perform the carriage return.
7 for terminals-This parameter determines the number of
null...

TL-130400-1001COL.NO.
Table 17.3AEntry Fields for Record Code AP (Continued)
COL.VALID
NAMEENTRIESCOMMENTS
36-37Transmission 0
Speedidentify the transmission rate at which data is
2
sent.
3-This is a read-only parameter.
.=.120= 110 bps(uses 2 stop bits)
.
132 = 300 bps(uses 1 stop bit)
143= 1.2 kbps(uses 1 stop bit)
or12 = 2.4 kbps(uses 1 stop bit)
1513 = 4.8 kbps(uses 1 stop bit)_14 = 9.6 kbps(uses 1 stop bit)
15= 19.2 kbps(uses 1 stop bit)
This is X.3 parameter 11.
38Flow Control of0 = PAD flowThis...

TL-130400-1001
Table 17.3AEntry Fields for Record Code AP (Continued)COMMENTS
suggested value =perform the line feed.
2 for terminals-This parameter determines the default value
of line feed padding.
-This is the number of null characters after a
line feed is sent to a device that the system
will pause before sending additional data.
-The carriage return padding field is normally
assigned. If terminals lose information at the
beginningof each line, the value in this field
during the data 
Vanspreviously...

TL-130400-1001
select another character.O-127= ASCII character to be used for line
O-l 27 = characterIdentify the character to be used in editing
suggested value =which willdisplay the current contents of the
18 (Control R) for
-See theprevious ASCIIcharacterset to
select another character.
ASCII character to be used for line
r the appropriate value (O-127) from
Table 
17.3B.-This option selects local (not CCITT
standardized) parameter number 1.
-Asynchronous host = 127
-Each APM user can specify the...

TL-130400-1001
Table 17.314Entry Fields for Record Code AP (Continued)
COMMENTS
transparently throughnetwork(transmit parity
received through network)
1 = check local parity and send space parity
through network (ignore parity received
through network)
-This parameter determines the default value
of eighth bit transparency.
-This function specifies that the PAD should
or should not check parity.
-This field is normally set to N for
asynchronous devices.
-This field selects local (not CCITT...

TL-130400-1001COL.COL.VALID
NO.NAMEENTRIESCOMMENTS
61-63Break Signal002-006 = numberAssign the length of the break signal to the
Timing
of incrementsasynchronous device.
%suggested value =-The selection must be made in increments
. . . .5 (250 ms) forof 50 ms, so a selection of 2 = 100 ms.
terminals
5 (250 ms) for host
64-66
Command
O-255 = numberIf this timer is enabled, it drops the
Inactivity Timerof incrementsconnection when no user commands are sent
suggested value =within the time period...

TL-130400-1001Table 17.3AEntry Fields for Record Code AP (Continued)
COL.COL.VALID
NO.NAMEENTRIESCOMMENTS
70
. . .Data Set SignalY = timer enabledThis field determines whether or not this timer
Wait-Down
N = timer disabledis enabled or disabled.
Timersuggested value =-The timer controls the delay between the.”Y for terminalstime when the user disconnects (goes on-
N for hosthook) and the time when the connection is
actually dropped.
-If Y is selected (enable), mark Record
Code Cl, columns 46-48, with the...