GTE Omni Si Database Technical Practices Manual

TL-130400-1001Feature Button18.4.9 The number shown in this column designates the feature
button to be used to assign and program the desired functions on
this specific IFP. Physically, the buttons are numbered starting
with the row of buttons nearest the keypad, starting at the top of
the row and proceeding downward in order, i.e., button number 1
is the top button in the first row; button number 9 is the top button
in the second row.
. . .NOTE: A FeatureComm II has one row of buttons (8) and the...

TL-130400-1001Remarks
Button Label
. . . .
Single-Line Feature-
Comm Feature
Button Assignments
Instructions
Key Plan Number
Prime Directory Number
Instrument Type18.4.13 At the originator’s discretion, enter any note or comment
to further clarify the programmable information.
18.4.14 Enter, if known, the description that should appear on the
button label when the telephone is installed. Preprinted labels
are available for most features and are packaged with the
instrument at the factory. Blank labels...

User Name
User Location
Intercom Group
s-
. . .
- Call Pickup Group
Feature Button
Function Assignment
CodeSVR 5210TL-130400-1001
18.6.4 Enter user’s name using last name only, if known. If
unknown, leave blank.
18.6.5 Enter a brief description of user’s location, i.e., room
number, post number, or grid location or floor.
18.6.6 Enter S.A.K.P. (Same As Key Plan) since all 
IFPs on this
Key Plan should be in the same intercom group. If more than
one intercom group is desired per Key Plan, enter S.A....

TL-130400-1001i
Prime Directory #User Namekey plan #
Instrument TypeUser Location
1213
14
15
16
Function Assignment Programming
1 Push & Hold FB (“Beep’)2. Push &Hold 2 (“Beep-Beep’)
3. Key In Function CodeVia Keypad
4. Push & Hold FB (“Beep’)
D-3988187
Button Data Entry Programming
1 . Push & Hold FB (“Beep’)2 - Key in Data Via Keypad
3. Push & Hold FB (“Beep’)
IIIf DSS Button Enter
IIf Feature Button0nlvI(1)(2)(3)
Enter User Data, AsRequired
10 -Dual Access
11 Direct Station Selection (DSS)12. Extended...

TL-130400-1001Feature Button Data18.6.11If the following functions or features have .been selected,
additional information about the feature button needs to be
entered:
0 Station speed calling
l Repertory dial
l Dual access
l Reminder
l Time and date
l Call forward
. . .l Special call forward
l Auto 
inercoml Message waiting
. .l Special call waiting
l Manual signal
If the information is known at the time of form preparation, enter it
in the column under the heading “If Feature Button Only”. If the...

--TL-130400-1001
Button Label18.6.13 Enter, if known, the description that should appear on the
button label when the telephone is installed.
Preprinted labels are available for most features and are
packaged with the instrument at the factory. Blank labels are
also provided to allow user discretion in button labeling.
. . .Upon completion, this form, along with the Key Plan and 
Multi-Line Feature Button Assignments, if applicable, must be sent to
the persons responsible for the following tasks:
l PABX...

TL-130400-1001
REFERENCES19.0 The following reference documents (Table 19.1)
complement/supplement the information provided in this practice:
Table 19.1 References
DOCUMENT
FujitsuGTEPractices:Hardware
Ordering
Guide:
Data Base
Sheets:
Configuration
Management:
Customer
Instructions:
NUMBERISSUEDESCRIPTION
TL-130000-1001 3Introduction/Features
TL-130500-1001 3System Configuration
TL-130100-1001 
13Operation
278-904-l 80I3IPD-200 Packet Data SystemITL-130300-1001 3
TL-130200-1001 3
FM-41...

TL-130400-1001Table 19.1References (Continued)
BESCRlPTlQN
Cl-278-41 0
Cl-278-41 1
Cl-278-41 2
Cl-278-41 71OMNI Series Attendant Manual
1Maid Service Features Insert
1OMNI Series Generic Station
User’s Guide (No Access Codes
Included)
1Asynchronous Packet Manager
User’s Guide
Cl-278-41 8Cl-473-3651Integrated Voice Messaging
System User’s Guide
1FeatureComm V/VI Handbook
for CD-100 Data
Cl-473-366
Cl-473-395
1FeatureComm V/VI User’s
Manual (Voice Features Only)
1FeatureComm V/VI Handbook
for PD-200 Data...

TL-130400-1001CROSS REFERENCE
Record Code
Number to
Recent Change
Number
-..
Record Code
=: Number to
Form Sequence
Number
Record Co,de
Number to
T Table Number
SW 521020.0 This section provides cross-references to other
documents which may prove useful in configuring the data base.
20.1 Table 20.1 provides a cross-reference of the record code
numbers to Recent Change numbers. When the Recent Change
number pertains to a specific record code column number, the
column number is included.
20.2 Table 20.2...

 rTL-130400-1001Table 20.1Cross Reference of Features to Record Codes and Recent Change
RecordRecord Code
Feature
CodesColumn(s)Recent Change Numbers Used in
UsedNumbersSupport of FeatureAccess AC
Code
all
.AttendantAT,.
ConSole CA
DC
DD
NC.
OFOT
ACA
TlACD AD
AF
AG
DKDT
HG
LD
z:
OFRA
SD
Tl
AIODTl
BLDUAT
BD
BKCA
CAS CF
BranchOEOT
SD
TlCAS MainAD
AF
AGAL
DK
HG
MH
TM
allAT=117, 181,184, 188, 218
allBD= 189
allBK= 190
allCA=183, 185,186, 187
-allNC=203, 211,213
allOF = 89, 209
30-32,45-47
56-67
all
all
all...