GTE Omni Si Database Technical Practices Manual

TL-130400-1001Record Code P2:17.7 Record Code P2, Figure 17.7, defines the parameters
Data Systemrequired by the data system ADMP processor. Record Codes
Global Parameter -Pl and P2 define the type of report the ADMP generates
Part 2and the destination for sending these reports. The ADMP
can generate accounting records and event records.
Accounting and events are stored in files.
s
. . . .SVR 5210Only one P2 record will exist for each ADMP report type;
therefore, this record code will contain a maximum...

TL-130400-1001II
I
I1
--Fi’ RI1AI1
NI; SI1  
c:’01’  DI; EII1I111
I’ !’ I1 
DNIC jSERVERi  g ;I’ P lI, DI Cl RIk Ig IIIII 
s;1 MlII; g II1 AIIIII
II-. .-IIII T III 1’1 III.I 0;I TI .m II’ El
I !!DI 1SEC 1
II
II
I
I 1HR ;
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~c-+-+-t-+--c--c--+101-+-+-+-+-+-+-+-+-+-t-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-~c-4l6141OlPl 21AICI I I I I I I I I , I I I I I I I I I I I I I I I I I I I I II
i-i
;-;
;-;
1-i
A-:
Figure 17.7Record Code P2: Data...

TL-130400-1001COL.
NO.
Table 17.7Entry Fields for Record Code P2
COL.
VALID
NAMEENTRIESCOMMENTS
12-13Report TypeAC = accountsThis field determines the type of report
EV = eventsgenerated.
IN = information
s-OA = overflow
. . .account
OE = overflow
event
,-WA = warning
14Report Records 0This field determines where the system will
to Destination 1send the report(s) listed in columns
212-13.
:L number0 = nowhere, reports are discarded
1 = RS-232C (ADMP maintenance console),
the reports appear on the ADMP...

TL-130400-1001Table 17.7Entry Fields for Record Code P2 (Continued)
COL.NO.
22-23
24-26
27-30
COL.NAME
Time Between
Outgoing Calls
(1 Second)
Start TimeHour
Start Time
Minute
Period (1 Hour)
X.1 21 Address
(DNIC)
X.1 21 Address
(server number)
X.1 21 Address
(sub-port)VALID
ENTRIES
300-255 =seconds
suggested value =
10 (010) seconds
30-23 = hour
qumber
30-59 = minute
7umber
300-255 = hour
7umber3-9 = number
O-9= number
O-9= number
D-3788187COMMENTS
This field determines the time (in seconds)
between...

TL-130400-1001Record Code Cl:17.8 Record Code Cl, Figure 17.8, defines the global
Data Systeminformation for call processing. One record is required per
Call Processing -system.
Data Part 1
T---------T-----------‘-----------------------------------------------------1III
III
I
II
IIiI8
I
I
IY-I
:-.F S N; R d
k:: E”IE g
I”- IID E(
) DP;
‘ESfAK I,lJE I
ST’
I MSII AZ;I XE I
I xI
I
I
I 

TL-130400-1001Table 17.8Entry Fields for Record Code ClCOMMENTS
Number of PortsThis field determines the maximum number of
ports configuredin the systemincluding the
Indicate the maximum number of routing
records entered in the system.
-See Record Code RT, columns 
12-l 4.
(Record Code RT, columns 15-l 
6) it will try
devices in this routing group until either an idle
device is found, all devices in this routing
record are tried, or the number of devices
ines the maximum number of
e to a rotary hunt...

TL-130400-1001Table 17.8Entry Fields for Record Code Cl (Continued)
COL.COL.VALID
NO.NAMEENTRIESCOMMENTS
29-31
. . . .Default
004 = 16 bytesThis is the default X.25 data packet maximum
Maximum X.25005 = 32 bytessize to be used when packet size negotiation
Packet Size
006 = 64 bytesis not in effect.s-. .007 = 128 bytes-Codes are CCITT standard.
008 = 256 bytes-This value is used when packet size
009 = 512 bytesnegotiation is not in effect (see Record Code
010 = 1024 bytesCP, column 38).
. .suggested value...

TL-130400-1001COL.
NO.Table 17.8Entry Fields for Record Code Cl (Continued)
COL.VALID
NAME
ENTRIESCOMMENTS
45
Type of
Accounting toPerform
.~.
o-2This field determines the type of data call
suggested value =accounting performed by the system.
2-This field is only valid when column 44 is Y.
0= no accounting, statistics are kept only on a
per-port basis
. .1 = X.25 accounting, APM-to-APM calls are
not accounted for
2 = full accounting, all calls are to be
accounted for
-For values 1 or 2, column 35 on...

TL-130400-1001Record Code C2:
Data System17.9 Record Code C2, Figure 17.9, provides the global
Call Processinginformation for data call processing. The “Private Herald” is
displayed when an asynchronous terminal is connected to its
Data - Part 2local APM. The “Profile Identifier” is displayed to request
terminal characteristics identification. One ‘record is required per
system.
T---------T---------------------------------------------------------------~Is- ’I.” I
I
I;II
I
‘-II-II
II
I
I
I
I
PRIVATE...

TL-130400-1001Table 17.9Entry Fields for Record Code C2
COL.COL.VALID
NO.NAMEENTRIESCOMMENTS
12-43Private HeraldA-Z = letterThis field determines the printable ASCII string
W-Vfor private herald.
-This is the actual private herald displayed
=-when a terminal comes up and has gone
through hunt-confirm sequence.
-Any ASCII characters are valid.
-It should not contain 
“(” (ASCII 56 Hex) or
“)” (ASCII 5D Hex). For example,” FGBS Data
Network” would be a valid entry to notify that a
user is now connected to...