GTE Omni Si Database Technical Practices Manual

TL-130400-1001Table 17.2Entry Fields for Record Code CPCOMMENTS
oup (A, B, C, or D) within PEC 0 is
-Card slot 11 cannot be used.
X.1 21 AddressThis field determines the 
DNIC of the X.121
- = not selected
Thisis the X.121address for thedeviceas the
network sees it. This address is like a phone
number for a data network.
-The X.121 addresses are gotten from a
network just as DID numbers are gotten from
a CO.
-The PD-200 system requires X.121
addresses.
-This address is used in the processing of
X.25 call...

 rTL-130400-1001COL.NO.
Table 17.2Entry Fields for Record Code CP (Continued)COL.
VALID
NAMEENTRIESCOMMENTS
21-28X.1 21 AddressO-9 = number(sever number)identify the sever number of the X.121
- = not selectedaddress.
-The sever number is the next eight digits
29-30
9.after the DNIC.
-The sever number identifies the PD-200
routing group.
X.1 21 Address
O-9 = number(sub-port)Identify the sub-port number of the X.121
- = not selected
address.
-Only asynchronous devices require an entry
in this field.
-These...

TL-130400-1001Table 17.2Entry Fields for Record Code CP (Continued)COMMENTS
N = notselectedwindow andpacket sizenegotiation that is
according to X.25 standards.
-If enabled, the window and packet size
facilities will always be placed in call request
packets to the device and checked in any call
or accept packets from the device.
-Standard 
CCITT X.25 negotiation rules will
be enforced. If not enabled, the facilities will
not be allowed from the device and will not be
sent to that device.
-Only X.25 
SPMs...

TL-130400-1001COL.
NO.Table 17.2
Entry Fields for Record Code CP (Continued)
COL.VALID
NAMEENTRIESCOMMENTS
41Make Paid Calls Y = selected
(always Y for
.~.ADMP)
-..N = not selected
. ._This field is only valid for asynchronous
terminals/modems connected to 
APMs.-The field specifies the charging default for
the connect command from this device.
-The default is either to make caller paid
calls or collect (reverse charge) calls.
-This is part of the facility field of the call
packet.
-If this field is...

TL-130400-I 001
COL.
NO.44Table 17.2Entry Fields for Record Code CP (Continued)
COL.NAME
Is the Data
System a DCE?
Y-ADMP or MDRVALID
ENTRIES
Y = selected
NOTE: Enter Y if
SPM is connected
to a PDN (Public
Data Network)
N = not selected
(usually N)
M=MDR
- = not connected
MDA = PX25deviceCOMMENTS
This field determines if this device is
configured as a DCE.
Enter M if the port is connected to an MDR.
-If columns 31-34 are marked PX25, enter
A in this field.
SVR 52108187D-339 

TL-130400-1001Record Code AP:17.3 Record Code AP, Figure 17.3, defines the common
Data Systeminterface parameters for each APM (Asynchronous Packet
Asynchrouous PortManager). This record code is only used for asynchrouousports, and an entry for each APM must be found here.
There are three types of parameters that are defined for each of
the terminals or groups of terminals. They are:
.=.
. . . .l X.3 parameters
l Local parameters
l Optional subscription parameters
For normal applications, all terminals...

TL-130400-1001
X .35 PARAMETERSIII I II
I
I
I
I
. ..J-I
iI -I
I
I
c-+-+-l-+-+-+-+-+-+-+-+-+-+-+-+-+-+-~-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-~ ,1fj171,,1A#p, , I I , I I , I I I I I I I , , 1 I t , 1 , , 1  , , , 1  i , 1,L-~-I--L-L--L-I--L-*-~-*-~-1-~-1-*-1-~-~-~-~-1-~-~-~-~-~-~-~-~-~-~-~-~-~-~ ,-r-------------------------------------------------------------------------I--~II
iILOCAL X .35IPARAMETERSII AlI N’I s,
I ClI 01I DII ElI 1
I I
I I
I ’
I ,
I 
II ’
I I
I 
’I I
I 1
I 
1-+-;71819101-c-4I I
-.I.-.4I I I...

TL-130400-1001Table 17.3AEntry Fields for Record Code APCOMMENTS
-EnterPEC 0.
Which circuit on the card is beingused?
transfer mode.
0 = escape not possible
suggested value =1 = DLE character initiates escape
1 for terminals2-127 = selected character initiates escape
-If another ASCII character is required, see
Table 
17.3B.-This parameter specifies the character used
to indicate to the terminal that the user wants
to enter command mode.
-The value is the decimal equivalent of the
ASCII character to be...

1COL.
NO.21-23
24-26TL-130400-1001
Table 
17.3AEntry Fields for Record Code AP (Continued)
COL.NAME
3ataForwarding
Zhalacters
,dle TimerVALID
ENTRIES
0
1
2
4
8
16
32
64
128suggested value =
2 for terminals
0 for host
0 = data will not be
forwarded in the
timeout.
l-255 = length of
delay in 
50-msincrements
suggested value =
20 for terminals
0 for hostCOMMENTS
Indicate a predefined character or set of
characters that are typed by the user (DTE) to
tell the terminal to transmit/forward a packet.
0 
= user...

TL-130400-1001COL.NO.
Table 17.3AEntry Fields for Record Code AP (Continued)
COL.VALID
NAMEENTRIESCOMMENTS
27Device Flow 0
ControlThis field allows the PAD (remote end) to
ortemporarily slow the output from this device
>-1when the PAD is momentarily unable to
. . .suggested value =receive more data .
0 for terminalsThis parameter determines the default value of
1 for hostdevice flow control.
.--If this parameter is enabled, the PAD will be_able to flow control the device when the PAD
falls behind in...