Home > GTE > Communications System > GTE Omni Si Database Technical Practices Issue 1 Manual

GTE Omni Si Database Technical Practices Issue 1 Manual

Here you can view all the pages of manual GTE Omni Si Database Technical Practices Issue 1 Manual. The GTE manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 81

TL-130100-1001
NOTE:If requested number is not verified, error tone is heard, the LED is extinguished, and
the entry may be made again.
3.6.8Message Waiting (24)
STEPOPERATIONRESULT1Depress and hold WAIT.(a) WAIT LED on.
(b) Beep heard.
(cl
2Release.(a) WAIT LED flashes
(b) Display cleared.
3Enter Message Center number.” XXXX”
4To store, depress and hold WAIT.
(a) WAIT LED on steady.
(b) Beep heard.(c) “NEW ENTRY STORED”
5Release.Display cleared.
(a) WAIT LED flashes.
(b) “MESSAGE WAITING”NOTE:If you...

Page 82

- -TL-130100-1001
STEPOPERATION
5Release.RESULT(a) REP DIAL LED off.(b) Display clears or reverts to the time
and date.NOTES:
1.See Special Data Programming /Entry for pause programming information.
2.If you have a FeatureComm III/IV instrument, key in the desired Alpha Entry and then
a 
# to move the cursor to the next field.
3.6.10
Special Call Forward (20)
STEPOPERATIONRESULT
1Depress and hold SP FWD.(a) SP FWD LED on.
(b) Beep heard.
(c) “SPEC CALL FWD”
2Release.
3
(a) SP FWD LED flashes.(b) “TYPE =...

Page 83

.: .;. _..._TL-130100-1001
OPERATIONRESULT
9Release.(a) SP FWD LED off.(b) Display clears or reverts to the time
and date
3.6.11Special Call Wait (31)
OPERATIONRESULT
1Depress and hold SP WAIT.(a) SP WAIT LED on.
(b) Beep heard.(c) “SPECIAL WAIT”
2
3
a
9
10
Release.
Enter type (e.g., 1).
1= Wait Only
2= Wait Except
Depress #.“TYPE = 
1”
Enter desired number.“NUMBER = 
-‘I“NUMBER = XXXX”
Depress #.“NUMBER = ”-Enter up to three or more numbers
as in Steps 5 and 6 above or
depress 
# to skip field.After...

Page 84

TL-130100-I 001
3.6.12
Station Lock (02)
STEPOPERATION
RESULT1Depress and hold LOCK.(a) LOCK LED on.
(b) Beep heard.(c) “STATION LOCK”
2Release.
(a) LOCK LED flashes.(b) “LOCK CODE = 
”
3
Enter code.If incorrect, (b) Beep heard.
(b) LOCK LED flashes.(c) “NEW CODE = 
?”if correct,“NEW CODE = 
?”
4
(Preprogrammed code is 000)
Enter new code.“CODE VERIFY = 
?”
5Enter new code again.If incorrect, (a) Triple beep heard.
(b) “NEW CODE = 
?”If correct,
“STORE LOCK CODE”
6To store, depress and hold LOCK.
(a)...

Page 85

TL-130100-1001
STEPOPERATIONRESULT9NOTES:
1.
2.Depress 
#.“19= ”Enter alpha information, e.g., 
GIGI.“19 = GIGI”Depress 
#.Display cleared.
Enter desired number.
“X xxxxxxx”To store, depress and hold SPEED.(a) SPEED LED on steady.
(b) Beep heard.
(c) “NEW ENTRY STORED”
Release.(a) SPEED LED off.
(b) Display clears or reverts to the time and
date.
The above may be repeated for an additional 19 entries.
See Special Data Programming/Entry for pause programming information.
3.7Alphabetical Operation of...

Page 86

TL-130100-1001
NOTES:1.A new account code may be entered at any time during the call, but only the last
number entered will be associated with the call.
2.
3.To abort an entry, depress the ACCT button before the number is entered.
If the account code is more than eight digits, only the last eight digits entered will be
stored.
3.7.2
Automatic Callback “CAMP 
ON” (37)
Automatic Callback provides access to either of two PABX features: Station
Camp-On with Callback or On-Hook Trunk Call Queuing. AUTOMATIC...

Page 87

TL-130100-1001
STEPOPERATION
RESULT6
7
8NOTES:
1.
2.Trunk call unanswered, several
attempts will be made. On last
attempt,
If first (and only) line callback is not
answered.
If instrument busy and a trunk recall
is attempted.(c) “PLEASE DIAL” for call to trunk.
(d) C BACK LED off.
(a) Same as Steps 4a and 4b.
(b) Camp-on terminated.
(c) C BACK LED off.
(a) Same as Steps 
4a, b, and c.
(b) Same as Steps 6b and c.
Same as Step 6a.
If instrument is busy, a line recall
will not be attempted until station is...

Page 88

TL-130100-I 001
Operating any of the above feature buttons shall cause the instrument to turn
on the speakerphone (if equipped) or the monitor.NOTE:In the event the user of a multi-line set has not preselected a line
or a line has not been automatically selected by the instrument via
the preference feature, the instrument will delay turning on the
speakerphone/manitor amplifier until a line has been manually
selected.
(4Automatic Line Seizure, Single-Line Set
1Depress desired feature button.(a)...

Page 89

TL-130100-10012.If the line selected is a non-dial line, i.e., a personal CO line, the prompt is not
displayed. Instead, CO dial tone wil be heard as confirmation of successful CO
seizure.
See also: Line Preference
Line Seizure
Line Selection
3.7.4
Bad-Line Reporting “BAD LINE” (45)
Bad-Line Reporting allows the identification of a faulty line to the system by
pressing the BAD-LINE feature button while on the connection.
STEPOPERATIONRESULT
Starting from a connected call state.
1Depress “BAD LINE”.(a)...

Page 90

TL-130100-1001
STEP
OPERATION
RESULT3d
4(Incorrect, non-working, or restricted(a) Reorder tone heard.
number)(b) “CANNOT COMPLETE”
To end or abandon call, go
ON-HOOK.
integrated Featurephone call termination differs from the POTS phone
termination because the lntegrated Featurephone decides how the call will be
treated. When the call is offered, the Integrated Featurephone may:
(a)ACCEPT the call. An ACCEPT does not constitute an answer but
rather indicates that the phone will notify its user of the...
Start reading GTE Omni Si Database Technical Practices Issue 1 Manual

Related Manuals for GTE Omni Si Database Technical Practices Issue 1 Manual

All GTE manuals