Home > GTE > Communications System > GTE Omni Si Database Technical Practices Issue 1 Manual

GTE Omni Si Database Technical Practices Issue 1 Manual

Here you can view all the pages of manual GTE Omni Si Database Technical Practices Issue 1 Manual. The GTE manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 111

.-TL-130100-1001
5.If the user’s set is equipped with a CONSULT/TRANSFER button and/or a three-way button, the user may intermix the FLASH button with the other buttons to perform
the desired operation. The LED associated with the last button used reflects the
status of the latest condition. For example, instead of the user depressing the
FLASH button to establish a three-way call, the user could have depressed the
three-way button. The THREE-WAY LED turns on steady and the FLASH LED is
extinguished for...

Page 112

r-TL-130100-1001
(d)The call origination can be completed even though the called lineis busy (pseudo call waiting).
(4The call will automatically release privacy on a current line call.
Intercom Call - Origination
STEPOPERATIONRESULT
Begin from off-hook talking state or off-hook receiving dial tone and “PLEASE
DIAL”.
1Depress I COM, if off-hook receiving
dial tone.
2Enter destination via a DSS buttonnumber and proceed as with a
normal line-to-line call.(a) I COM LED same.
(b) “XXXX” as programmed in...

Page 113

TL-130100-1001NOTE:If the control line is busy, and there is a call waiting button, the call waiting LED will
flash, a distinctive call waiting beep will be heard, and the display will show the
information for the waiting call. The intercom call will be treated as a waiting call.
intercom Call - Termination, Single-Line Set
STEPOPERATIONRESULT
1Go off-hook.Distinctive ringing heard.
2Continue as with a normal line-to-line
call.
NOTE:If your phone is busy, and you do not have a call waiting button, you...

Page 114

TL-130100-10013.7.24
Line Buttons (Multi-Line Sets Only)Line Buttons are required on a multi-line set. Each line button has two 
LEDs
associated with it: the PRIMARY status indicator, or UPPER LED; and the
SECONDARY status indicator, or LOWER LED. The primary LED shows the
IDLE, RINGING, HOLD, EXCLUSIVE HOLD, and BUSY status of the line.
Prior to going off-hook, the PREFERENCE LED will show the I-USE
condition, if applicable.Line buttons, once programmed, utilize both 
LEDs to provide status
information...

Page 115

TL-130100-1001
Table 3.13 Status LEDsThe upper LED is considered the Status LED and presents the following
indications:
LED
CONDITION
STEADY LEDSTATUS
The line is busy, either at this instrument, or at another phone for
multi-set lines.
WINKING LED
FLASHING LED
HOLDING LEDThe line is ringing, and the alerting type is delayed.
The line is ringing, and the alerting type is immediate.
The line has a call on non-Exclusive Hold, i.e., the held call may be
retrieved from any instrument at which this multi-set...

Page 116

TL-130100-1001
MULTI-LINEFEATURE
SETS LINE
BUTTONS
BUTTONSACTIVATEDPRIMARY STATUS
o-112Figure 3.3 Integrated Featurephone Status and 
Wse LEDs
8h375210 

Page 117

TL-130100-1001NOTES:
1.With the exception noted in note 2 below, preference features shall apply to
all PABX or CO LINE buttons (prime, control, and non-control lines). DSS
buttons are not considered as line buttons.
2.Ringing line preference and incoming call preference shall also apply to the
INTERCOM button on those instruments so equipped.
3.If preference (or manual preselection) chooses a ringing line, the call source
shall be displayed during the alerting interval. This display is the basis for
the...

Page 118

r._- -TL-130100-1001
NOTES:
1.For 1 through 3 above, a particular line must be selected
(manually or 
automaticaily) either prior to or after the user
action in order for a line seizure to occur. For 4 through 6,
the line currently selected (indicated by the associated LINE
button’s I-USE LED being on) is the line that will bereseized. Refer to line selection for information on how lines
are manually and automatically selected.
2.Selection of the one line on a single-line set is doneautomatically by the...

Page 119

TL-130100-1001(clManual Line Seizure - Handset Off-Hook/Line Released
STEPOPERATIONRESULT
1
2Begin with handset off-hook and line(a) Associated I-USE LED on.
previously released by RLS button.(b) RLS LED on.
Depress either NEW CALL or RLS
button.(a) Associated LED on.
(b) Line is seized.
(c) Dial tone heard.
(d) “PLEASE DIAL”
(e) NEW CALL or RLS LED off.
Proceed as with a normal line-to-line
call.
((3Manual Line Seizure - Handset Off-Hook/Line Busy
STEPOPERATIONRESULT
1Begin with handset off-hook and
the...

Page 120

TL-130100-1001
Preselection is defined as the manual selection of a line when the user
depresses the LINE button while the instrument is in an on-hook condition,
i.e., the handset is on-cradle, and the speakerphone and monitor features
are idle. Preselection overrides any previous preselected line or any line
choice made by any of the preference features which may be in effect. The
instrument guarantees the preselection choice for at least 10 seconds before
allowing any of the preference features, if...
Start reading GTE Omni Si Database Technical Practices Issue 1 Manual

Related Manuals for GTE Omni Si Database Technical Practices Issue 1 Manual

All GTE manuals