GTE Omni Si Database Technical Practices Issue 1 Manual

TL-130100-1001STEPOPERATIONRESULTAfter 10 seconds,
(e) The preselection choice may be
overridden by any possible
combination programmed for
preference.
NOTES:
1.Once a line seizure has taken place, preselection has no meaning until the user
returns to an on-hook condition.
2.After going on-hook, the line shall remain as the selected line for 10 seconds,
allowing a new call to take place without changing lines. The user may override the
choice by selecting another line. The I-USE LED remains on for as...

TL-130100-10013.If the user chooses a ringing line via preselection, a call source display shall
be displayed during the alerting interval. This display is the basis for the
user to determine how to handle the call.
4.Anytime the user depresses a LINE button while on another line, the other
line is released and the line associated with the depressed LINE button is
seized, if idle.
O-118
81873.7.28
Line TypesSeveral types of lines may appear on the Featurephone. These are: 
single-set line, multi-set...

TL-130100-1001
A call to an instrument with secondary lines is alerted on one of the
secondary lines when the prime line is busy. There is no need to provide call
waiting operation; terminations occur to idle appearances as long as any are
available, and the line is treated as busy when all line appearances are busy.
Should alerting occur while the user is in conversation on a line, the active
call may be placed on hold and the ringing’line appearance answered.
A call may be originated from any idle line...

- -TL-130100-1001
CO lines can be assigned only on multi-line sets. The appearance of a CO
line need not, however, be restricted to a single instrument. As with PABX
lines, CO lines can be configured in multi-set arrangements, so that a
particular CO line can be accessed from more than one station instrument.
When the line is busy, other attempts to use the line by the sharing stations
will result in a trunk busy tone being received at these stations.
(0CQ Line Operation - Call Origination
1.The user...

TL-130100-10013.7.29Manual Signaling “BUZZ” (39)Manual Signaling (BUZZ) permits the user of one Integrated Featurephone to
signal the user of another lntegrated Featurephone with a buzz tone without
originating a call and regardless of the call related state of the phones.
STEPOPERATIONRESULTBegin from any state.
1Depress BUZZ.(a) BUZZ LED on for l/2 second.
(b) BUZZ tone sounded at destination
for 
l/4 second. If busy, BUZZ
is muted. (Operation may be repeated).
3.7.30
Message Leaving “LV MSG” (25)LEAVE...

- -TL-130100-1001
STEPOPERATIONRESULTIf message leaving is unsuccessful,(a) Reorder tone heard.
(b) “NO MESSAGE LEFT”
NOTES:
1.If the call has been diverted to another station (i.e., call forwarding, call pickup, etc.),
the message will be left at the original called instrument.
2.The above procedure may also be performed by either party while the call is in an
answered state. However, when involved in a stable two-way conversation, the
Integrated Featurephone leaving the message (only Integrated...

STEPOPERATlONRESULT
4Dial the message leaving access(a) If successful, confirmation tone heard.
code, the number representing the(b) If unsuccessful, reorder tone heard.
message to be left, and the directory
number of the party to receive the
message.
(c)Message Retrieval -Integrated Featurephone Only
STEPOPERATIONRESULT
1Leave MSG button flashing.
Depress LEAVE MSG.Oldest message first displayed.
2To see time and date of message,
depress 
#.TOD displayed.
3To scroll to next message, depress #.Second...

TL-130100-1001
NOTES:1.The MESSAGE WAITING (MS CTR) LED on the instrument that is the prime or
control appearance for a directory number will be lit for a message waiting request.
2.If the instrument does not have a MESSAGE WAITING (MS CTR) LED, the message
will be ignored.
3.9.31Monitor “MONTR” (04)
The MONITOR button controls the activation/deactivation of the monitor
amplifier. The associated LED indicates the monitor is on.
The first depression of the MONITOR feature button will initiate the monitor...

TL-130100-1001
NOTES:1.On a multi-line set, whenever the instrument is off-hook or when the speakerphone
or monitor are on and the instrument initiates ringing, the ringing shall be abbreviated
to present only three cycles of ringing to the instrument user.Although the ringing is
stopped, the visual alerting on the line button will continue until answered.
2.The message “PLEASE HANG UP” is displayed when the user turns the monitor (or
speakerphone) feature on and the handset is off-hook. The message...

.._. -TL-130100-1001
STEP
OPERATlONRESULT
1Enter, via keypad or a repertory dial(a) “NUMBER ENTERED”
button, the code calling access code,(b) Code number is signaled over audible
zone code, and code number to becode calling system.
signaled.
2Continue as with Basic Calling
(Internal/External).
(b)Dictation AccessDictation Access feature allows users to access the centrally located dictation
equipment.
STEPOPERATIONRESULTBegin from an idle off-hook state receiving dial tone and “PLEASE DIAL”.
1Enter the...