GTE Omni Si Database Technical Practices Issue 1 Manual

TL-130100-1001STEPOPERATIONRESULT
6Release feature button.Display remains.
7Continue down the button row(s)
performing Steps 5 and 6 above.Same as Steps 5 and 6 above.
82-3 seconds after last button is
released.(I) Double beep heard.
(2) Display clears.
(clDisplay Test (Test Code 4)
STEPOPERATIONRESULT
1Depress & hold #.(a) Beep heard.
(b) “DIAGNOSTICS”
2Release #.“WHICH TEST =?‘I
3Depress 4.(a) The following each appear for 2-3
seconds in sequence.
(1) “DISPLAY TEST”
(2) All 
LCDs active.
(3) Blank...

TL-130100-1001Table 3.8 Control Codes
CONTROL CODES
CODES
2Ring Pitch
3Ring Volume
5Clock Display
6
7Clock Type
Pause Duration
8Call Forward On No Answer
Duration
9Preference (Multi-Line Sets Only)
3.4.1Call Forward on No Answer Duration (Control Code 8)
STEPOPERATIONRESULT
1Depress and hold *.(a) Beep heard.
(b) “CONTROL PROGRAM”
2Release *.“WHICH CONTROL = ?‘I
3
Depress 8 (Control code for CALL
FORWARD).“FWD NO ANS = IOSEC”
NOTE:Any of these timing choices may be selected. If number 1 is selected,...

TL-130100-1001
3.4.2Clock Display (Control Code 5)
STEPOPERATION
RESULT
1
2
3NOTE:
7Depress and hold 
*.(a) Beep heard.
(b) “CONTROL PROGRAM”
Release 
*.Depress 5.
Choose one of the following:“WHICH CONTROL = ?”
111= DISPLAY; 0 = NONE”
1 
- To display time and date whenever the station is idle (feature button not
required).
0 
- For no display of time and date except via feature button operation
(reprogram a feature button to operate Time and Date).
Depress 1.“DISPLAY ON IDLE”
Depress 0.“NO IDLE...

--TL-130100-1001
OPERATIONRESULT
NOTE:Choose the desired clock type and depress the appropriate key. If 
12-hour time is
chosen, the HH:MM is followed by A or P for AM or PM, respectively. If 24-hour
time is chosen, the HH:MM display will not be followed by an A or P, and HH will
range from 00 to 23.
6Depress and hold *.(a) Beep heard.
(b) “NEW ENTRY STORED”
7Release *.Display clears.
Pause Duration (Control Code 7)
STEP
OPERATIONRESULT
Depress and hold *.(a) Beep heard.
(b) “CONTROL PROGRAM”
Release...

TL-130100-1001STEPOPERATlONRESULT
2Release *.“WHICH CONTROL = ?”
3Depress 3 (control code for
preference).“PREF = 
10100”
4Depress * to see preference types.“PREF = R l P L I”
5Enter 0 for OFF or 1 for ON.
6
7Depress # to go to next field.
Continue for 5 fields.
Depress and hold 
*.
OS and 1s as entered.
“XXXXK“NEW ENTRY STORED”
8Release *.Display clears.
5210Preference Types
The five different types of preference include Incoming and Outgoing.
R=Incoming Ringing: The line with an incoming call, with...

TL-130100-1001
Preference selection is intended to be dynamic and constantly changing as
the lines are made busy and go idle. The choosing of a line by a preference
feature is intended to mean its “predesignation for use” if and when the
instrument user goes off-hook. This should not imply either a reservation of
a line or seizure of the line.
3.4.6
Ring Pitch (Control Code 2)
STEPOPERATIONRESULTDepress and hold *.
Release *.Depress 2. (Control program for
pitch.)
Depress desired tone (l-8).
Adjust pitch...

TL-130100-1001STEPOPERATIONRESULT
6Depress and hold *.(a) Beep heard.
(b) “NEW ENTRY STORED”
7If no entry is made, the last level
sounded will be the programmed level.
8Release *.Display clears.
NOTE:If you have a FeatureComm III/IV instrument, the preprogrammed Ring Volume is 1.
If you have a FeatureComm V/VI, it is 4.
3.4.8
Setting the Time and Date
STEPOPERATIONRESULT
1
2
3
8
NOTE:Depress and hold 0 (Access Code for(a) Beep heard.
Administration).(b) “ADMINISTRATION”
Release 0.
“QO:OOA DAY OO/OO”Enter...

rTL-4 30100-l 001
Table 3.9 Function Codes Required for Programming/Reprogramming the Feature
Buttons, Listed Alphabetically
FUNCTION CODEFUNCTION
CODEAccount Code
Automatic Call Announcing
Automatic Callback
Automatic intercom
Bad Line
Busy Override
Call Announce
Call Forward
Call Hold
Call Park
Call Waiting
Conference
Data Option
Data Protection
Dial Display
Direct Station Selection (DSS)
Dual Access
Executive Priority Call
Extended Call Pickup
Extended Group Select
Flash
Forced Busy
Group/Directed...

TL-130100-1001Table 3.10 Function Codes Required for Programming/Reprogramming the Feature
Buttons, Listed by Code
CODE
FUNCTIONCODEFUNCTION
00
01
:;
04
05
06
ii;:
09
10
11
E
14
:z
:;
19
20
21
22
23Unassigned
Ringer Cutoff
Station Lock
Flash
Monitor
New Call
Last Number Redial
Save Number Redial
Station Speed Calling
Repertory/Feature Access
Dual Access
Direct Station Selection (DSS)
Extended Group Select
Reminder
Timer/Elapsed Time
Ti.me & Date (Clock)
;;;;seWySpeakerphone (Optional)
Call Forward...

TL-130100-I 0013.51
Programming/Reprogramming a Feature on a Button
STEPOPERATIONRESULT
1
2
3
4
NOTE:
5
6
NOTE:
7
8
9
O-66Remain on-hook.
Depress and hold feature button to
be assigned change.(a) Single beep heard.(b) “FEATURE NAME” of existing feature
displayed.
Release the feature button.
(a) LED flashes throughout programming.(b) “CONTENTS STORED” or “FEATURE
NAME” displayed.
Depress and hold 2.
(a) Double beep heard.(b) “CHANGE FUNCTION”
Release 2.
(a) LED flashes.(b) “FUNCTION CODE =
.I’-The 
*...