GE Logiq 9 Service Manual

GE MEDICAL SYSTEMS PROPRIETARY TO GE
D
IRECTION 2294854-100, REVISION 3  LOGIQ™ 9 PROPRIETARYMANUAL 
Chapter 7 Diagnostics/Troubleshooting 7-53
7-12-1System Does Not Power On / Boot Up (cont’d)
Figure 7-46   System does not Boot (contd.)
Turning off the LOGIQ 9. 

GE MEDICAL SYSTEMSPROPRIETARY TO GE
D
IRECTION 2294854-100, REVISION 3  LOGIQ™ 9 PROPRIETARYMANUAL   
7-54 Section 7-12 - Troubleshooting Trees
Section 7-12Troubleshooting Trees (cont’d)
Figure 7-47  BEP1 Connector Reference 

GE MEDICAL SYSTEMS PROPRIETARY TO GE
D
IRECTION 2294854-100, REVISION 3  LOGIQ™ 9 PROPRIETARYMANUAL 
Chapter 7 Diagnostics/Troubleshooting 7-55
Section 7-12Troubleshooting Trees (cont’d)
Figure 7-48  Boot Sequence Illustrations 

GE MEDICAL SYSTEMSPROPRIETARY TO GE
D
IRECTION 2294854-100, REVISION 3  LOGIQ™ 9 PROPRIETARYMANUAL   
7-56 Section 7-12 - Troubleshooting Trees
7-12-3 Noise in Image
Figure 7-49   Noise in Image
Noise is shown in Image.
YES
NOIs there any electrical 
devices that affect the 
Scanner?
Keep the Scanner away from those 
electrical devices.
Check probes. 

GE MEDICAL SYSTEMS PROPRIETARY TO GE
D
IRECTION 2294854-100, REVISION 3  LOGIQ™ 9 PROPRIETARYMANUAL 
Chapter 7 Diagnostics/Troubleshooting 7-57
7-12-4 Unable to Scan
Figure 7-50   Unable to Scan
Unable to scan!
Check the probe connection.YESNO
Are probes connected in 
right way?
Restart the scanner.
Are other operations 
possible?YES
Check the HV power supply unit. NO
END 

GE MEDICAL SYSTEMSPROPRIETARY TO GE
D
IRECTION 2294854-100, REVISION 3  LOGIQ™ 9 PROPRIETARYMANUAL   
7-58 Section 7-12 - Troubleshooting Trees
7-12-5 Trackball
Figure 7-51   Trackball Troubleshooting
The trackball is low sensitive!
Remove the ball from the Trackball, 
and clean it.
YES
NODoes the trackball move at 
all?
Replace the trackball unit. 

GE MEDICAL SYSTEMS PROPRIETARY TO GE
D
IRECTION 2294854-100, REVISION 3  LOGIQ™ 9 PROPRIETARYMANUAL 
Chapter 7 Diagnostics/Troubleshooting 7-59
7-12-6 Minimum Cable Configuration for System to Boot
The following cables must be connected between the INT I/O board and the rest of the system:
• Cables to Hard Disk (inside Back End Processor)
• Patient I/O cable to Patient I/O box
• I/O RS-232 serial cable to Front Panel
• ACCTRL cable between INT I/O and ACCTRL (power-on signal)
• DC Power cable to Front...

GE MEDICAL SYSTEMSPROPRIETARY TO GE
D
IRECTION 2294854-100, REVISION 3  LOGIQ™ 9 PROPRIETARYMANUAL   
7-60 Section 7-12 - Troubleshooting Trees
7-12-8 System Does Not Power Off / Shutdown
Figure 7-52   Power Off / Shutdown Flowchart
Is the ON/OFF switch
illuminated with a
green color?
Yes
If the ON/OFF switch is illuminated with an amber color, the scanner is in
stand-by mode which indicates that it has been Shut Off, but not completely
Powered Down.
If the ON/OFF switch is not illuminated at all, the...

GE MEDICAL SYSTEMS PROPRIETARY TO GE
D
IRECTION 2294854-100, REVISION 3  LOGIQ™ 9 PROPRIETARYMANUAL 
Chapter 7 Diagnostics/Troubleshooting 7-61
7-12-9 Monitor Troubleshooting
NOTE: Reset the monitor settings to the factory defaults prior to troubleshooting the monitor.
NOTICEComments to remember about the 17” monitor.
The monitor is the diagnostic monitor and is only connected to 115 VAC.
The monitor powers down with the front end card rack.
Power output from AC Control Box:
When the monitor is not...

GE MEDICAL SYSTEMSPROPRIETARY TO GE
D
IRECTION 2294854-100, REVISION 3  LOGIQ™ 9 PROPRIETARYMANUAL   
7-62 Section 7-12 - Troubleshooting Trees
7-12-9Monitor Troubleshooting (cont’d)
Figure 7-53   
Error on the monitor display!
Set the Monitor setting to the default.NOYES
Do the colors seem 
abnormal?
Does the Contrast or the 
Brightness adjustment 
seem improper?
Adjust Contrast and Brightness. YESNO
Does distortion occur on 
the monitor? Does the 
display area seems 
abnormal?
NO
Does the monitor...