GE F650 Manual

CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.1 ENERVISTA 650 SETUP SOFTWARE
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-19
3.1.7.3  System setup menu
(*) indicates online only, (**) indicates offline only
3.1.7.4  Breaker menu
3.1.7.5  Protection elements menu
This option shows all protection elements available in the relay as shown in the following two tables (exact menu depends 
on firmware version).
For firmware versions below 7.50, each gr oup of protection elements includes the specific...

3-20F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.1 ENERVISTA 650 SETUP SOFTWARECHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
For firmware version 7.50 and above, there are six setting g roups of protection elements. Protection element groups are 
within each setting group.
Table 3-5: Protection elements menu, f irmware version 7.50 or above
(*) indicates online only, (**) indicates offline only
For firmware version 7.5 and above, the specific protection element menus shown are available under each...

CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.1 ENERVISTA 650 SETUP SOFTWARE
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-21
Firmware version 7.50 and above also include Frequency and Miscellaneous menus in the Protection Element section.
Phase OVPhase overvoltage (59P)
Neutral OV HighNeutral overvoltage, high level (59NH)
Neutral OV LowNeutral overvoltage, low level (59NL)
Negative Sequence OVNegative sequence overvoltage (47)
Auxiliary OVAuxiliary overvoltage (59X)
Auxiliary UVAuxiliary...

3-22F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.1 ENERVISTA 650 SETUP SOFTWARECHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
3.1.7.6  Control elements menu
This option shows all protection elements available in the relay as shown in the following two tables (exact menu depends 
on firmware version).
Table 3-7: Control elements menu, f irmware version below 7.50
Control Elements
Setting Group Control elements can be used in either a single setting group (default mode-all units can 
op
erate...

CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.1 ENERVISTA 650 SETUP SOFTWARE
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-23
Table 3-8: Control elements menu, f irmware version 7.50 and above
3.1.7.7  Inputs/Outputs menu
Section that contains the settings for all input and output boards and the Force Outputs and Virtual inputs activation tools.  
(*) indicates online only, (**) indicates offline only
This section shows the settings related to inputs  and outputs for the different boards available in...

3-24F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.1 ENERVISTA 650 SETUP SOFTWARECHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
3.1.7.8  Quick settings menu
 This menu allows quick access to the main Setpoints of the relay.
Figure 3-10: Quick Settings
3.1.7.9  Relay conf iguration menu
This is the relay configuration section in which the relay ca n be configured using internal states or already compiled 
equation on PLC Editor
.
Relay 
Conf iguration
OutputsConf iguration of contact output operate and...

CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.1 ENERVISTA 650 SETUP SOFTWARE
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-25
The following figures show an example of the default factory configuration for F650:
Figure 3-11: Relay conf iguration
SwitchgearUp to 16 configurable switchgear elements. A switchgear element can be a breaker, a line 
se
lector switch, a grounding selector switch, a busbar selector switch, etc. This screen 
allows conf iguration of type of contacts, opening and closing time,...

3-26F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.1 ENERVISTA 650 SETUP SOFTWARECHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
Figure 3-12: HMI conf iguration
3.1.7.10  Logic Conf iguration menu
This logic configuration allows creating more complex configurations, using the graphical PLC, than using the tables from 
Relay Configuration. For file management  detailed information go to section 3.1.4 File management menu.
File description:
*.pep:Header for Logic project: PLC project file containing the...

CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.1 ENERVISTA 650 SETUP SOFTWARE
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-27
3.1.7.11   IEC 103 Conf iguration menu
This menu allows to update the IEC 103 configuration of the unit.
Figure 3-13:  IEC 103 Conf igurator
See chapter 5.13
3.1.7.12  Clock menu
This menu allows updates to the date and time of the relay, either synchronizing them with the PC clock, or entering the 
information manually. 
Figure 3-14: Clock 

3-28F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.1 ENERVISTA 650 SETUP SOFTWARECHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
3.1.8  Actual values menu
The menu bar in the main screen of EnerVista 650 Setup  software shows the ACTUAL menu option. This option 
concentrates and displays all the status of protection, control elements, metering, counters information, oscillography, 
events, fault locator, etc. This section shows only the structure of menus in EnerVista 650 Setup.
3.1.8.1  Front panel
The...