GE F650 Manual

CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.2 HUMAN-MACHINE INTERFACE (HMI)
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-39
Figure 3-20: Enhanced keypad description
8s ed for clos ing the us er programmable  
switchgear. It is fully Sr ogrammable .
8VHGIRUFORVLQJWKHXVHUSURJUDPPDEOH
VZLWFKJHDU,WLVIXOO\SURJUDPPDEOH
F1.  Us er  programmable .
F2.  Us er programmable .
F3 / *. User  programmable.
Up  Key. Us ed f or  select ing menus , 
subme nus, DQGseW tin JV
Do wn Key.  Us ed for selec...

3-40F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.2 HUMAN-MACHINE INTERFACE (HMI)CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
3.2.3.2  Command push button
The unit incorporates a command pushbutton located at the bottom right side of the HMI interface and at the top left for 
Enhanced interface, with three options: local, remote, and off. The firs t option (LOCAL) allows executing operations in local 
mode (HMI, front  port, and rear COM2 port). The second option (REM OTE) allows operation execution...

CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.2 HUMAN-MACHINE INTERFACE (HMI)
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-41
3.2.5  Screen contrast
Regulation of screen contrast should be performed as described below depend on display model selected:
Basic HMI:Dedicated screen contrast regulator is  located below cover sealing system. See Figure 3-21: Detail of front port 
and cover sealing system.
Enhanced HMI: Backlight level regulation can be performed by usin g enhanced keypad. Reset button must...

3-42F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.2 HUMAN-MACHINE INTERFACE (HMI)CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
3.2.6.2  Text menu hierarchy
The structure of HMI text menu is similar to the EnerVista 650 Setup menu in the actual values and settings (view and 
change) menus. The main menu shows the following options:
3.2.6.3  Actual Values
The Actual Values menu option in HMI concentrates and displays all the status of protection, control elements, metering, 
counters information,...

CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.2 HUMAN-MACHINE INTERFACE (HMI)
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-43
Protection >Protection Blocks
Phase Current
Neutral Current
Ground Current
Sens. Ground Current
Neg. Seq. Current
Thermal Model
Voltage
Power
Voltage
Power
Control Elements > Frequency
Synchrocheck 
Autoreclose
Breaker Failure
VT Fuse Failure 
Broken Conductor
Setting Groups
Locked Rotor
Pulse Counters
Analog Comparators
Load Encroachment
Max. Number of starts
Digital...

3-44F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.2 HUMAN-MACHINE INTERFACE (HMI)CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
To enter this menu press the shuttle key or enter key when the option Actual Values is selected in main menu. A secondary 
level is displayed with different sublevels as shown on  . Pressing Up/down keys or rotating the shuttle key, (left for moving 
up and right for moving down) select the next level to  be displayed, press the enter/shuttle key again to enter in next level...

CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.2 HUMAN-MACHINE INTERFACE (HMI)
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-45
Figure 3-24: Snapshot event navigation HMI shows an example of snapshot events navigation:
Press enter/shuttle key from the default main screen and enter in the main text 
menu.
Move the shuttle key  or press up-down keys until a single scroll bar character 
(o) appears in the left part of Snapshot event header.
Press enter/shuttle key to enter in the snapshot events menu)...

3-46F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.2 HUMAN-MACHINE INTERFACE (HMI)CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
In the second option, fault reports can be viewed thro ugh the HMI Fault Report menu accessed by pressing the enter/
shuttle key. The display shows information from the last te n faults, including both general information and metering 
screens for each fault. Displayed information starts with the most recent fault, and previous faults can be viewed by 
rotating the enter/shuttle...

CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES 3.2 HUMAN-MACHINE INTERFACE (HMI)
GEK-113000-AF F650 DIGITAL BAY CONTROLLER 3-47
3.2.6.6  View settings menu
To enter this menu press the enter/shuttle key when the option View Settings is selected in main menu (o). A secondary 
level is displayed with different sublevels. Pressing up-down keys or rotating the shuttle key, (left for moving up and right 
for moving down) select the next level to be displayed (o), press the enter/shuttle key again to enter...

3-48F650 DIGITAL BAY CONTROLLER GEK-113000-AF
3.2 HUMAN-MACHINE INTERFACE (HMI)CHAPTER 3:  INTERFACES, SETTINGS & ACTUAL VALUES
(*) This menu changes as indicated in table  4.35 for firmware version 7.50 or above.
Neutral TOC       > Neutral TOC 1..3
Neutral IOC       > Neutral IOC 1..3
Neutral Dir        > Neutral Dir 1..3
Ground Current    >
Ground TOC        > Ground TOC 1..3
Ground IOC        > Ground IOC 1..3
Ground Dir         > Ground Dir 1..3
Sens. Ground Curr > Sens. Ground TOC. > Sens. Ground...