Gateway tablet pc User Manual

							171
Using a wired Ethernet network
www.gateway.com
Equipment you need for a wired Ethernet 
network
For a wired Ethernet network you need:
■An Ethernet jack on each desktop computer, notebook, and tablet PC.
- OR -
An Ethernet card installed in each desktop computer.
- OR -
An Ethernet PC Card installed in each notebook.
■An Ethernet router. Select a router that gives you the following features:
■A jack for connecting to a cable or DSL modem.
■The ability to assign IP addresses to your networked computers 
dynamically. This prevents intruders from seeing the computers over 
the Internet.
■A built-in firewall to protect the computers on your network from 
intruders trying to access your data over the Internet.
■Built-in switching (with enough ports for all computers and devices 
on the network) so you will not have to purchase a hub or switch.
■If you did not purchase a router that includes built-in switching or if the 
router does not have enough ports to attach all your computers, an 
Ethernet hub or switch with enough ports for all computers and devices 
in the network.
■Ethernet cable going from each computer to the router, hub, or switch.
ImportantFor best results, all Ethernet components should be either 
standard Ethernet (10 Mbps), Fast Ethernet (100 Mbps or 
10/100), or Gigabit Ethernet (1000 Mbps or 10/100/1000). 
A mixture of components rated at different speeds will 
result in your network running at the speed of the slowest 
rated component. 
						

							172
Chapter 11: Networking Your Tablet PC
www.gateway.com
Using a wireless Ethernet network
A wireless Ethernet network is ideal for creating a home or office network or 
adding mobility to an existing wired Ethernet.
Wireless Ethernet is available at two different speeds. IEEE 802.11a and 
IEEE 802.11g wireless Ethernet run at speeds up to 54 Mbps, or about half the 
speed of Fast Ethernet. 802.11b wireless Ethernet runs at speeds up to 11 Mbps, 
or approximately the same speed as standard wired Ethernet. This type of 
network allows you the freedom to move about your home or office with your 
tablet PC. For example, you can take your tablet PC from your home office to 
your patio without having an Ethernet jack available.
The two most common types of wireless Ethernet networks are access point 
and peer-to-peer.
WarningRadio frequency wireless communication can interfere 
with equipment on commercial aircraft. Current aviation 
regulations require wireless devices to be turned off while 
traveling in an airplane. IEEE 802.11a, IEEE 802.11b, and 
IEEE 802.11g communication devices are examples of 
devices that provide wireless communication. For 
instructions to turn wireless Ethernet on and off, see 
“Turning your wireless Ethernet on or off” on page 177.
ImportantSee “Safety, Regulatory, and Legal Information” on 
page 267 for general wireless regulatory and safety 
guidelines.
ImportantThe speed of a wireless network is related to signal 
strength. Signal strength is affected by the distance 
between your wireless network devices, by radio 
interference, and by interference from natural obstructions 
such as walls, floors, and doors. 
						

							173
Using a wireless Ethernet network
www.gateway.com
Example access point wireless Ethernet 
network
By using an access point, you can join a wireless Ethernet network and access 
a wired Ethernet network. An access point also lets you access the Internet.
The following is an example of an access point wireless Ethernet network. The 
network is made up of an access point, a cable or DSL modem, and your 
computers. The access point is the central control point for the network. 
Attached to the access point is the cable or DSL modem that provides access 
to the Internet. Each of the computers or Ethernet-ready devices communicate 
with the access point using radio waves. If your computer does not have built-in 
wireless Ethernet capabilities, you need to add a wireless PCI card (desktop), 
PC card (notebook), or USB adapter.
Tips & TricksIf you want to access a wireless Ethernet network from 
your wired Ethernet network, connect an access point to 
the router, switch, or hub. For more information about 
accessing a wired Ethernet, see “Using a wired Ethernet 
network” on page 169.
Cable/DSL modem
Access point
USB wireless 
adapter 
						

							174
Chapter 11: Networking Your Tablet PC
www.gateway.com
Equipment you need for an access point 
wireless Ethernet network
For an access point wireless Ethernet network you need:
■A wireless Ethernet PCI card installed in each desktop computer
- OR -
A wireless Ethernet USB adapter attached to each desktop computer
- OR -
A notebook or tablet PC with wireless Ethernet built-in
- OR -
A wireless Ethernet PC Card installed in each notebook that does not have 
wireless Ethernet built-in
■A wireless Ethernet access point to connect your wireless Ethernet network 
to the Internet or a wired Ethernet network
ImportantIEEE 802.11b and IEEE 802.11g use the same radio 
frequency. IEEE 802.11a uses a different radio frequency 
than IEEE 802.11b and IEEE 802.11g. All wireless 
Ethernet components should use the same frequency. A 
combination of IEEE 802.11a and IEEE 802.11b or 
IEEE 802.11a and IEEE 802.11g components will 
not work. Some wireless devices can broadcast and 
receive signals on both frequencies.
A mixture of IEEE 802.11b and IEEE 802.11g components 
will result in your network running at the speed of the 
slower IEEE 802.11b components. 
						

							175
Using a wireless Ethernet network
www.gateway.com
Example peer-to-peer wireless Ethernet 
network
Use a peer-to-peer (also known as ad hoc) wireless Ethernet network if you are 
setting up or joining a temporary computer-to-computer network. This type of 
network does not include access into a wired network or the Internet. You can 
create this type of network to quickly move files from one computer to another. 
						

							176
Chapter 11: Networking Your Tablet PC
www.gateway.com
Equipment you need for a peer-to-peer 
wireless Ethernet network
For a peer-to-peer wireless Ethernet network you need:
■A wireless Ethernet PCI card installed in each desktop computer
- OR -
A wireless Ethernet USB adapter attached to each desktop computer
- OR -
A notebook or tablet PC with wireless Ethernet built-in
- OR -
A wireless Ethernet PC Card installed in each notebook that does not have 
wireless Ethernet built-in
For more information
For more information about purchasing equipment for your home or office 
Ethernet network, discuss your particular needs with your Gateway store 
representative. In addition, several books and Internet sites are dedicated to 
networking. See these sources for more information about networking your 
home or office with wired or wireless Ethernet.
Help and 
SupportFor more information about networking, tap Start, then tap 
Help and Support.
Type the keyword networking in the Help and Support 
Center Search box  , then tap the 
arrow. 
						

							177
Using your tablet PC on a network
www.gateway.com
Using your tabletPC on a network
Installing and configuring your tablet PC for 
Ethernet networking
A guide in .PDF format has been included on your hard drive that provides 
instructions for installing and configuring both wired and wireless Ethernet 
networking on your tablet PC. To access this guide, tap 
Start, All Programs, then 
tap 
Gateway Documentation.
Turning your wireless Ethernet on or off
To turn wireless Ethernet on or off using the Dashboard:
1Press Hot Key 1   to open the Dashboard.
2To turn wireless Ethernet on, tap to check the Wireless Operation check box.
-OR-
To turn wireless Ethernet off, tap to clear the 
Wireless Operation check box.
See “Using the Motion Dashboard” on page 160 for more information.
WarningRadio frequency wireless communication can interfere 
with equipment on commercial aircraft. Current aviation 
regulations require wireless devices to be turned off while 
traveling in an airplane. IEEE 802.11a, IEEE 802.11b, and 
IEEE 802.11g communication devices are examples of 
devices that provide wireless communication.
ImportantWhen using wireless connectivity in low-reception areas, 
be sure to keep your hands clear of the antenna zones. 
						

							178
Chapter 11: Networking Your Tablet PC
www.gateway.com
To turn wireless Ethernet on or off using Windows XP:
1Ta p  Start, then tap Control Panel. The Control Panel window opens. If your 
Control Panel is in Category View, tap 
Network and Internet Connections. The 
Network and Internet Connections window opens.
2Ta p / D o u b l e - t a p  Network Connections. The Network Connections window 
opens.
3Button-tap Wireless Network Connection, then tap Enable to turn on wireless 
Ethernet or tap 
Disable to turn off wireless Ethernet. 
						

							12
179
Moving from
Yo u r  O l d
Computer
If your new tablet PC is replacing an old computer, you 
may have personal data files, Internet settings, a printer or 
other peripheral devices, and other unique computer 
settings that you want to move from your old computer 
to your new one. Read this chapter to learn about:
■Using the Files and Settings Transfer Wizard
■Transferring Files
■Transferring Internet Settings
■Installing your old printer or scanner
■Installing your old programs 
						

							180
Chapter 12: Moving from Your Old Computer
www.gateway.com
Using the Files and Settings 
Transfer Wizard
You can move your data files and personal settings, such as display, Internet, 
and e-mail settings, from your old computer to your new one by using the Files 
and Settings Transfer Wizard. The wizard also moves specific files or entire 
folders, such as My Documents, My Pictures, and Favorites.
To open the Files and Settings Transfer Wizard:
■Ta p  Start, All Programs, Accessories, System Tools, then tap Files and Settings 
Transfer Wizard
.
Help and 
SupportFor more information about using the Files and Settings 
Transfer Wizard, tap Start, then tap Help and Support.
Type the keyword using transfer wizard in the Help and 
Support Center Search box  , then 
tap the arrow.