Digital Projection Titan Sx+600, Sx+700 User Manual

Rev C August 2009 Page 4.37
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Lamp
Press  and   to select Lamp.
  Press 
 to open the Lamp submenu.
The middle row shows the current lamp setting.
Change Lamp Setting
Press  and   to select Change Lamp Setting.
Press  to open the Lamp Setting control box.
•
•
Notes
 
Setup Menu 
  Lamp
Setup menu, continued
continued 

Page 4.38  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 In single lamp modes:
  - if the running lamp fails, the 
other lamp will automatically be 
switched on.
 The selected lamp mode:
  - will not be applied until 
OK is 
selected
  - will be applied gradually over a 
period of 30 seconds
  - will not be applied until the end 
of any warm-up or cool-down 
period that has already started.
Lamp power
Press  and   to select the Lamp Power...

Rev C August 2009 Page 4.39
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 
Setup Menu 
  On Screen Display
 The On Screen Display will 
move to the centre of the DMD 
when Blanking is turned On.
  (see 
Geometry menu, earlier in 
this section).
 If a menu is opened, and no 
other key is pressed within the 
period set in the OSD Timeout 
menu, then the menus will 
disappear. When the   key 
is pressed again, the menus will 
reopen at the same point they 
were last...

Page 4.40  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Password
Entry to the password protected area is available to authorised service personel 
only.
Press  and   to select Password.
  Press 
 to open the Password control box.
Press  and   to select each digit in turn.
  Press 
 and   to adjust the digit from:
0 to 9
 then move to the next digit.
  Use 
 and   to select from
OK
 Press  
 to enter the password controlled area.
or  Cancel
Press   or...

Rev C August 2009 Page 4.41
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 
Setup Menu 
  Comunication
 When fresh batteries are 
inserted in the remote control, 
it will default to address 00. 
Remote control 00 is a master 
control,  able to control all 
projectors.
  If two or more projectors are set 
to the same address, they can 
be controlled from one remote 
control, provided they are 
connected by cable or in range 
of the infra red.
Communication
Press...

Page 4.42  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 
Setup Menu 
  Network
 Some items may be greyed out 
or not editable, due to the effect 
of other settings made in the 
Network submenu.
  For example, if a 
Wired 
Connection is selected:
  Wifi, Channel and SSID will be 
unavailable.
Setup menu continued
Network
Press  and   to select Network.
  Press 
 to open the Network submenu.
MAC Address
Projector’s unique ID  - for information...

Rev C August 2009 Page 4.43
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 IP Address cannot be changed 
if DHCP is set to ON.
  DHCP will set the the address, 
which will be displayed for 
information only.
Setup menu, Network continued
DHCp
Press  and   to select DHCP
  Press 
 to open the DHCP control box.
  Press 
 and   to select from:
On
Off
 Press  
 to apply the new DHCP setting.
Ip  Address
Press  and   to select IP Address
  Press 
 to open the IP...

Page 4.44  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 Subnet cannot be changed if 
DHCP is set to ON.
  DHCP will set the the subnet 
mask, which will be displayed 
for information only.
Subnet Mask
Press  and   to select Subnet
  Press 
 to open the Subnet control box.
  Press 
 and   to select from:
Automatic
or one of the following:
Class C Masks
255.255.255.254 
255.255.255.252 
255.255.255.248 
255.255.255.240 
255.255.255.224...

Rev C August 2009 Page 4.45
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Gateway Mask
Press  and   to select Gateway
Press  to open the Gateway control box.
Use  and   to select each number in turn.
Use  and   to adjust the number
then move to the next number.
Use  and   to select from
Apply
Cancel
Press   to apply the new Gateway Mask, or to exit without making the 
change.
•
Setup menu, Network continuedNotes
 Gateway cannot be changed if 
DHCP is set to ON.
  DHCP...

Page 4.46  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Wifi Channel
Press  and   to select Wifi Channel.
  Press 
 to open the Wifi Channel control box.
  Press 
 and   to select the channel number.
  Use 
 and   to adjust the channel number from:
0 to 14
 Use 
 and   to select from
 Apply
 Press  
 to apply the new Wifi Channel number.
or  Cancel
Press   or   to exit without making the change.
SSID
Projector’s ID  - for information only.
•
•
Setup...