Digital Projection Titan Sx+600, Sx+700 User Manual

Rev C August 2009 Page 4.7
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Indicators
Input status indicators
The indicator next to each input connector on the input panel will light as follows:
 off = input not selected
  green
 = input selected, signal detected and in range
 flashing green  = input selected, but signal not detected or out of range
Notes
 There are more indicators on 
the Control panel, and these are 
described on the next page.
5. Composite Video
6....

Page 4.8  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

The control panel
Keypad layout
The controls on the keypad are identical to those at the top of the remote control, 
and are described on the following pages.
Projector status indicators
The indicators on the control panel are as follows:
Power off = NO POWER
 green = normal RUNNING mode amber = STANDBY mode
Shutter amber = CLOSED green = OPEN
Error off = NO ERROR
 flashing  = ERROR (temperature)...

Rev C August 2009 Page 4.9
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

The remote control
Layout
Timeout
There is a 10 second timeout for the three Lens adjustment keys (see note on next 
page).
There is a separate, adjustable timeout for the On Screen Menus (see On Screen 
Display, in Setup Menu, later in this section).
Notes
 Many features are controlled 
from the menus using the menu 
navigation keys on the remote 
control or keypad.
 For more information about...

Page 4.10  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 Closing the shutter produces 
a better black than simply 
removing the signal, as the 
light source will be completely 
blocked by the shutter blade.
 When the OSD is OFF:
  -  all menu navigation keys are 
disabled.
  - keys such as 
 BrI 
(brightness) will still function, 
but the slider bars will not be 
visible on screen.
  When any of the three Lens 
adjustment keys is pressed, the...

Rev C August 2009 Page 4.11
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Auto-detect input mode
Press  to force the projector to re-detect the input mode 
(see Input modes and settings, earlier in this section).
Source information
Press  to display the source information screen.
Input
Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI
4. SDI
5. Composite Video
6. S-Video
7. Component
Or press the numbered keys 1–7 to change...

Page 4.12  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 For more information about 
input modes and input presets, 
see earlier in this section, Input 
modes and settings.
  See also 
Input menu, later in 
this section.
 A preset can be applied only to 
the same mode for which it was 
created. If the detected input 
mode does not match, then 
settings from the mode history 
or mode library will be applied.
  For more information about 
input...

Rev C August 2009 Page 4.13
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 The red, green and blue keys 
are disabled when the OSD is 
switched OFF.
 For more information about test 
patterns, see Setup menu, later 
in this section.
 The Saturation control is 
available for Composite, S-
Video and Component inputs 
only.
 The Phase control is available 
for RGB inputs only.
 For all adjustments on this page 
that require more than one key 
to be pressed:
  - after...

Page 4.14  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 The magnify feature utilises a 
digital zoom. Used with the pan 
control, this can be used to:
  - enlarge a section of the image
  - enable the use of multiple 
projectors to construct a large 
image from tiles.
 The pan control is available 
only when the image has been 
magnified.
 If the OSD moves off screen 
due to a change in image size, 
then pressing the size key will 
restore its...

Rev C August 2009 Page 4.15
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When the OSD is OFF, all menu 
navigation keys will be disabled.
  When the OSD is switched back 
ON, the menus will remain OFF 
until the   key is pressed 
again. The menus will then 
reopen at the same point they 
were last viewed.
 If a menu is opened, and no 
other key is pressed...

Page 4.16  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Press  to open the menu. The blue highlight moves to the first item in the 
menu, which may be submenu, for example the Projector Setup submenu.
To select a submenu, press  and  , for example the Lamp submenu. 
Press  to open the submenu. The submenu opens, with the title at the top.
To close the submenu and return to the previous level, press .
There may be up to three levels of submenu, so to...