Digital Projection Titan Sx+600, Sx+700 User Manual

Rev C August 2009 Page 4.47
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 Restore Defaults will restore 
all settings to factory 
defaults. All ISF settings will 
be lost (see next page).
  If you are not sure this is 
what you want to do, then 
either:
 make a record of all settings 
first 
 
or 
select No, then press .
 Following a restore to factory 
defaults, the projector will 
perform a self-test and enter 
Standby mode.
  This process will take up to 10...

Page 4.48  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Information Menu
 If Distributed By is visible, then 
the installer is  ISF	Certified, 
and the Save and Delete 
Preset options will not be 
available. Contact the installer 
for more information.
 
Information Menu 
  Projector Information
 
Information Menu 
  Source Information
Information menu
 To return...

Rev C August 2009 Page 4.49
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Digital Projection Information
Press  and   to select Digital Projection.
  Press 
 to see the DP Information screen.
•
Information menu continuedNotes
  When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Information Menu 
  DP Contact Information 

Page 4.50  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall 

Rev C August 2009  Page 5.1
5. Userware
Contents
Introduction ..........................................................................................................................................5.3
Applet version...................................................................................................................................5.3
Disconnect ....................................................................................................................................5.3...

Page 5.2  Rev C August 2009
5. Userware  Digital Projection TITAN sx+600/700. User Manuall

MCGD page ........................................................................................................................................5.14
The MCGD measurement procedure ................................................................................................5.14
MCGD values...

Rev C August 2009 Page 5.3
Digital Projection TITAN sx+600/700. User Manual  5. Userware

Notes
 To use the Titan Userware the 
java Runtime Environment
 
software must be installed on 
your browser. This software can 
be downloaded, free of charge 
from www.java.com.
  The LAN IP Address of the 
projector can be found in the 
Network submenu of the Setup 
menu, as described in section 
4. Controlling the projector
.
 Whenever the projector is 
connected to mains power, 
whether in Running mode or...

Page 5.4  Rev C August 2009
5. Userware  Digital Projection TITAN sx+600/700. User Manuall

Standalone version
To install the Userware, simply copy the file (from the CD, or downloaded from 
the Digital Projection website), to a folder on the computer.
Double click on the filename to start the software.
The Userware interface is organised into a number of pages, as listed below:
Show  Lens        Image   Screen
MCGD  TCGD        Global   Modal
info        System   Discover
Each page is described in full...

Rev C August 2009 Page 5.5
Digital Projection TITAN sx+600/700. User Manual  5. Userware

Show page
The Show page is the first to display when the browser connects to the projector .
To return to the Show page at any time, click on Show.
On / Off
Click On to switch the projector On.
Click Off to switch the projector into Standby mode.
Shutter Open / Closed
Click on Shutter O to open the shutter.
Click on Shutter C to close the shutter.
Freeze / Un-Freeze
Click on Freeze to freeze the display on the...

Page 5.6  Rev C August 2009
5. Userware  Digital Projection TITAN sx+600/700. User Manuall

Input Presets
recall
To recall a set of modal settings that have been saved:
Click on Preset, and select one of the Presets A - S, from the drop down menu.
Click on Recall.
  The projector will switch to the saved input source, and redetect  the input mode 
before applying the saved modal settings.
Save
To save the current input source, mode and modal settings:
Click on Preset, and select one of the Presets A -...