Digital Projection Titan Sx+600, Sx+700 User Manual

Rev C August 2009 Page 4.17
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Slider bar
The highlighted slider bar shows which 
control is active currently.
To adjust the slider press  and .
Parameter selection
To select from a number of parameters, 
(shown one at a time to the right), 
press  and .
These two items are greyed out and 
the values are blank, showing that they 
are not available, due to the effect of 
settings made in other menus, or due 
to the type of input...

Page 4.18  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Input menu
 To return to the main menu, press  up to three times.
 From the main menu:
Press  and   until Input is highlighted.
Press  to open the Input menu. The blue highlight moves to the first item in 
the menu. The  symbol shows which input is currently selected.
Input Source
Press  and   to select from:
1. RGB1
2. RGB2
3. DVI
4. SDI
5. Composite Video
6. S-Video
7. Component
Press  to...

Rev C August 2009 Page 4.19
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 For more information about 
input modes and input presets, 
see earlier in this section, Input 
modes and settings.
 
Input Menu 
  Presets
 
Input Menu 
  Presets
 
    Recall Presets A ~ H
Presets
Sixteen sets of parameters can be saved and recalled (A – S). The parameters 
saved for...

Page 4.20  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 
Input Menu 
  Presets
 
    Save Presets A ~ H
Save presets
Press  and   to select Save Preset.
  Press 
 to open the Save Presets A ~ H submenu.
To save the current set of parameters, press  and   to select one of the 
Presets.
 For Presets J to S, select Save Preset J ~ S then press...

Rev C August 2009 Page 4.21
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Picture Menu
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 The Saturation slider is 
available for Composite, S-...

Page 4.22  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 For more information about 
User gamma settings, see 
section 5. DP Userware.
 Parametric Gamma adjustment 
is available only when 
Parametric is selected in 
Gamma selection, above.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for RGB1 and RGB2 
inputs only.
Gamma Correction
Video recordings are often supplied with a gamma adjustment applied....

Rev C August 2009 Page 4.23
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
 When User Aspect is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect 
and V Aspect settings made in 
the Geometry menu.
 The Sharpness slider is 
available for Composite, 
S-Video and Component SD 
inputs only.
Aspect Ratio
Press  and   to select Aspect Ratio.
  Press 
 and   to select...

Page 4.24  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Geometry Menu
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Aspect Ratio selection can be 
found in both the...

Rev C August 2009 Page 4.25
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 Horizontal and Vertical 
Aspect Ratio adjustments are 
available only when User is 
selected in Aspect Ratio, (see 
previous page).
 Keystone adjustment can be 
found in both the Geometry and 
Projector Setup menus.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for graphics based 
RGB sources only.
User Horizontal Aspect Ratio
Press  and   to...

Page 4.26  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 
Geometry Menu 
  Resolution
 Input Detection should 
normally be set to Automatic. 
However, if the incoming video 
signal is non-standard, the 
projector may not be able to 
select an appropriate input 
mode.
  In this case, 
Input Detection 
should be set to Manual or 
Custom.
 Input Standard is available 
only if Input Detection is set to 
Manual.
Resolution
Press  and   to select...