Digital Projection Titan Sx+600, Sx+700 User Manual

Rev C August 2009  Page 3.1
3. Getting Started
Contents
Switching the projector on ...............................................................................................................3.2
Selecting an input or test pattern ...................................................................................................3.2
Input ................................................................................................................................................3.2
Test pattern...

Page 3.2  Rev C August 2009
3. Getting Started  Digital Projection TITAN sx+600/700. User Manuall

Selecting an input or test pattern
Input
Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI
4. SDI
5. Composite Video
6. S-Video
7. Component
Or press the numbered keys 1–7 to change directly to the input:
Test pattern
 If you have no video source connected to the projector, then you can display a test 
pattern as follows:
Press  on the remote control, to select a...

Rev C August 2009 Page 3.3
Digital Projection TITAN sx+600/700. User Manual  3. Getting Started

Notes
 Each time a new lens is 
fitted	to	the	projector,	
the calibration procedure 
must be carried out. See 
Setup menu, in Section 4. 
Controlling the projector.
  For more detailed information 
about:
  - using the control keys on the 
remote control or keypad,
  - using the menus,
  see the next section: 
Controlling the projector.
 When any of the three Lens 
adjustment keys is pressed, the 
blue...

Page 3.4  Rev C August 2009
3. Getting Started  Digital Projection TITAN sx+600/700. User Manuall
Adjusting the projected image
Picture settings
Press a  key, followed by  and   to adjust these picture settings:
  Brightness   
 BRI 
Contrast   
 CON 
Saturation   
 SAT 
Phase   
 PHASE 
Aspect ratio   
 ASPECT
Geometry settings
Press Keystone  KEYST
followed by  and  to adjust the keystone correction.
Press Position  
 POS   (for all inputs except DVI)
followed by , ,  and  to adjust the picture...

Rev C August 2009  Page 4.1
4. Controlling the projector
Contents
Overview ...............................................................................................................................................4.4
Controlling the projector.....................................................................................................................4.4
Input modes and settings...

Page 4.2  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Input menu .........................................................................................................................................4.18
Input Source ...................................................................................................................................4.18
Presets...

Rev C August 2009 Page 4.3
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Control Panel Backlight ..................................................................................................................4.32
Component Video Sync ..................................................................................................................4.32
Keystone...

Page 4.4  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Overview
Controlling the projector
The projector can be controlled from:
the remote control
the keypad
the RS232 input
the Ethernet input
For more information about controlling the projector using the RS232 and 
Ethernet inputs, see Remote communications protocol in section 7. 
Appendix.
For information about how to connect the projector, see Connecting the 
projector in section 2. Installation,...

Rev C August 2009 Page 4.5
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Input modes and settings
Input mode detection
The projector can automatically detect the following parameters from the incoming 
video signal:
line frequency
frame rate
interlace / progressive
From these parameters the projector can determine input mode, for example:
 input source  horizontal  vertical    mode
composite  15.73KHz  60.0Hz = NTSC
RGB1  31.51KHz  60.0Hz = SDTV 480p
SDI  33.8KHz...

Page 4.6  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Any subsequent changes that you make to the modal settings will be saved in the 
mode history,  with the input mode.
If a new signal is detected, the mode history for the previous signal will be saved in 
the mode history, and the new mode added, along with a new set of default settings. 
Thus the projector builds up a history of input modes, and the required settings for 
each mode, depending on...