Digital Projection Titan Sx+600, Sx+700 User Manual

							
Rev C August 2009 Page 4.17
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Slider bar
The highlighted slider bar shows which 
control is active currently.
To adjust the slider press  and .
Parameter selection
To select from a number of parameters, 
(shown one at a time to the right), 
press  and .
These two items are greyed out and 
the values are blank, showing that they 
are not available, due to the effect of 
settings made in other menus, or due 
to the type of input signal.
Parameter list
To select from a list of parameters, 
press  and .
Menu controls
Some menus have controls, as shown in the examples below.
Notes
 Some  menus items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
Input
Picture
Geometry
Colour
Setup
Information
1.RGB1
2.RGB2
3.DVI
4.SDI
5.CompositeVideo
6.S-Video
7.Component
Presets 
						

							
Page 4.18  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Input menu
 To return to the main menu, press  up to three times.
 From the main menu:
Press  and   until Input is highlighted.
Press  to open the Input menu. The blue highlight moves to the first item in 
the menu. The  symbol shows which input is currently selected.
Input Source
Press  and   to select from:
1. RGB1
2. RGB2
3. DVI
4. SDI
5. Composite Video
6. S-Video
7. Component
Press  to confirm your selection.
•
•
•
Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Input Menu
 For more information about 
the input connections, see 
section 2. Installation
, and 
section 7. Appendix.
 When an input has been 
selected, the projector will 
automatically detect input mode 
settings such as line rate and 
resolution etc.
  To force the projector to re-
detect the input mode settings, 
press .
Input
Picture
Geometry
Colour
Setup
Information
1.RGB1
2.RGB2
3.DVI
4.SDI
5.CompositeVideo
6.S-Video
7.Component
Presets 
						

							
Rev C August 2009 Page 4.19
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 For more information about 
input modes and input presets, 
see earlier in this section, Input 
modes and settings.
 
Input Menu 
  Presets
 
Input Menu 
  Presets
 
    Recall Presets A ~ H
Presets
Sixteen sets of parameters can be saved and recalled (A – S). The parameters 
saved for each Preset are:
all settings from the Picture menu,
all settings from the Input menu (1 – 7)
all settings from the Geometry menu, except Keystone
all settings from the Colour menu, except Global
Press  and   to select Presets. 
  Press 
 to open the Presets submenu.
recall presets
Press  and   to select Recall Preset.
  Press 
 to open the Recal Presets A ~ H submenu. Any presets that have 
been saved are indicated by their description, for example D: in this example.
To recall a set of parameters that has been saved, press  and   to select 
one of the Presets.
 For Presets J to S, select Recall Preset J ~ S then press 
 to open the 
J~S submenu. Press 
 and   to select the Preset.
  Press 
 to confirm your selection.
  The Preset parameters will be loaded.
•
•
•
•
Input menu continued 
						

							
Page 4.20  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 
Input Menu 
  Presets
 
    Save Presets A ~ H
Save presets
Press  and   to select Save Preset.
  Press 
 to open the Save Presets A ~ H submenu.
To save the current set of parameters, press  and   to select one of the 
Presets.
 For Presets J to S, select Save Preset J ~ S then press 
 to open the 
J~S submenu. Press 
 and   to select the Preset.
  Press 
 to confirm your selection.
  If this Preset has been used before, but only if the Input source h as been 
changed, then the following  message will be displayed.
 Press 
 and   to select either OK or Cancel.
  Press 
 to confirm your selection.
  The parameters will be saved to the selected preset, and the follo wing message 
will be displayed.
•
•
Input menu continued 
						

							
Rev C August 2009 Page 4.21
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Picture Menu
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 The Saturation slider is 
available for Composite, S-
Video and Component inputs 
only.
 The Hue slider is available for 
NTSC inputs only.
Picture menu
 To return to the main menu, press  up to three times.
 From the main menu:
Press  and   until Picture is highlighted.
Press  to open the Picture menu. The blue highlight moves to the first item in 
the menu.
Brightness
Press  and   to select Brightness.
  Press 
 and   to adjust the slider (-128 to +127).
Contrast
Press  and   to select Contrast.
  Press 
 and   to adjust the slider (-128 to +127).
Saturation
Adjusts the saturation at white peak levels.
Press  and   to select Saturation.
  Press 
 and   to adjust the slider (0 to 255).
Hue
Adjusts the color balance from green to blue, using the red level as a reference.
Press  and   to select Hue.
  Press 
 and   to adjust the slider (0 to 255).
•
•
•
•
• 
						

							
Page 4.22  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 For more information about 
User gamma settings, see 
section 5. DP Userware.
 Parametric Gamma adjustment 
is available only when 
Parametric is selected in 
Gamma selection, above.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for RGB1 and RGB2 
inputs only.
Gamma Correction
Video recordings are often supplied with a gamma adjustment applied. The 
projector’s gamma adjustment can be used to correct for this.
Press  and   to select Gamma.
  Press 
 and   to select from:
Parametric  Enables the gamma slider
User download  Applies the gamma settings made externally using the DP 
Userware on a personal computer. (default gamma of 2.2)
2.2 Limited DVI  Expands DVI signal to use full dynamic range with gamma 2.2
2.4 Limited DVI  Expands DVI signal to use full dynamic range with gamma 2.4
Graphics  Enhanced highlights and contrast
NTSC  NTSC colour space, with a gamma of 2.2
PAL  PAL colour space, with a gamma of 2.2
Linear  gamma of 1.0
Punch  Enhanced brightness and increased colour saturation for high 
ambient environments.
Parametric Gamma
Press  and   to select Parametric Gamma.
  Press 
 and   to adjust the slider (1.0 to 3.0 in 0.1 steps).
Phase
Phase should be set automatically by the projector, but can be adjusted manually to 
correct for shimmering or poor quality definition on, for example, fine text.
Press  and   to select Phase.
  Press 
 and   to adjust the slider (0 to 31).
•
•
•
picture menu continued 
						

							
Rev C August 2009 Page 4.23
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
 When User Aspect is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect 
and V Aspect settings made in 
the Geometry menu.
 The Sharpness slider is 
available for Composite, 
S-Video and Component SD 
inputs only.
Aspect Ratio
Press  and   to select Aspect Ratio.
  Press 
 and   to select from:
Fill   This will best fit the incoming source to fill either the height or 
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.6:1 (16:10)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
Native  The image will be displayed pixel for pixel. The image will be 
centred, with a black border if smaller than 1400 x 1050 or 
cropped if larger.
Sharpness
Press  and   to select Sharpness.
  Press 
 and   to adjust the slider.
•
•
picture menu continued 
						

							
Page 4.24  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Geometry Menu
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
 When User Aspect is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect 
and V Aspect settings (see 
next page).
Geometry menu
 To return to the main menu, press  up to three times.
 From the main menu:
Press  and   until Geometry is highlighted.
Press  to open the Geometry menu. The blue highlight moves to the first item 
in the menu.
Horizontal Position
Press  and   to select H Position.
  Press 
 and   to adjust the slider.
Vertical Position
Press  and   to select V Position.
  Press 
 and   to adjust the slider.
Aspect Ratio
 Press  and   to select from:
Fill   This will best fit the incoming source to fill either the height or 
width without changing the aspect ratio of the source.
User Aspect
1.33:1 (4:3)
1.6:1 (16:10)
1.78:1 (16:9)
2.35:1 (Scope)
1.66:1 (Vista)
1.85 (Flat)
Native  The image will be displayed pixel for pixel. The image will be 
centred, with a black border if smaller than native resolution or 
cropped if larger.
•
•
•
•
Input
Picture
Geometry
Colour
Setup
Information
HPosition
VPosition
AspectRatio
UserHAspect
UserVAspect
Keystone
Phase
Resolution
Blanking
1.85:1(Flat)
128
64
500
500
0
127 
						

							
Rev C August 2009 Page 4.25
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 Horizontal and Vertical 
Aspect Ratio adjustments are 
available only when User is 
selected in Aspect Ratio, (see 
previous page).
 Keystone adjustment can be 
found in both the Geometry and 
Projector Setup menus.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for graphics based 
RGB sources only.
User Horizontal Aspect Ratio
Press  and   to select User H Aspect.
  Press 
 and   to adjust the slider (internal number – adjust to fit).
User Vertical Aspect Ratio
Press  and   to select User V Aspect.
  Press 
 and   to adjust the slider (internal number – adjust to fit).
Keystone
Used to correct for distortion caused by the projector being mounted higher or lower 
than the screen.
Press  and   to select Keystone.
  Press 
 and   to adjust the slider (-128 to +127).
Phase
Phase should be set automatically by the projector, but can be adjusted manually to 
correct for shimmering or poor quality definition on, for example, fine text.
Press  and   to select Phase.
  Press 
 and   to adjust the slider (0 to 32).
•
•
•
•
Geometry menu continued 
						

							
Page 4.26  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 
Geometry Menu 
  Resolution
 Input Detection should 
normally be set to Automatic. 
However, if the incoming video 
signal is non-standard, the 
projector may not be able to 
select an appropriate input 
mode.
  In this case, 
Input Detection 
should be set to Manual or 
Custom.
 Input Standard is available 
only if Input Detection is set to 
Manual.
Resolution
Press  and   to select Resolution.
  Press 
 to open the Resolution submenu.
Input Detection
 Press  and   to select from:
Automatic Allows the projector to automatically detect an appropriate 
input mode for the signal.
Manual 
Allows the user to select an appropriate input mode from a list 
of common standards.
Custom 
Allows the user to completely customise the settings to suit the 
incoming video signal.
When Input Detection is set to Manual:
Press  and   to select Input Standard.
Press  and   to select from:
720p
XGA
XGA+
SXGA-
SXGA
SXGA+
1080p
UXGA
VGA
NTSC
PAL
SVGA
•
•
•
•
Geometry menu continued