Digital Projection Titan Sx+600, Sx+700 User Manual
Have a look at the manual Digital Projection Titan Sx+600, Sx+700 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 577 Digital Projection manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
Rev C August 2009 Page 4.27 Digital Projection TITAN sx+600/700. User Manual 4. Controlling the projector When Input Detection is set to Custom: Press and to select one of the adjustment sliders. Press and to adjust the slider to match the resolution of the incoming video signal. Blanking Blanking curtains can be applied to each edge of the picture. Press and to select Blanking. Press to open the Blanking submenu. Blanking On/Off Press and to select from: On Off Blanking adjust Press and to select the edge to be Blanked. Press and to adjust the slider (0 to 200). • • • • Geometry menu continuedNotes The adjustment sliders are available only if Input Detection is set to Custom. Total H Samples is available for RGB1 and RGB2 inputs only. V Offset is available for DVI input only. Geometry Menu Blanking The blanking curtains will not applied until Blanking is turned On. The On Screen Display will move to the centre of the DMD when Blanking is turned On. Set to zero for no blanking, eg the top edge in this example.
Page 4.28 Rev C August 2009 4. Controlling the projector Digital Projection TITAN sx+600/700. User Manuall Notes When using the menus, press OSD or to hide or reveal the On-Screen-Display. Colour Menu Some menu items may be greyed out - unavailable due to the effect of settings made in other menus, or due to the type of input signal. Read these notes on Colour and Global Colourimetry before making any settings in the Colour menus. Note that any changes made in the Global Colourimetry menu (see Setup Menu, later in this section) will affect ALL inputs, modes and presets for which Global Mode has been selected in the Colour menu. Colour menu To return to the main menu, press up to three times. From the main menu: Press and until Colour is highlighted. Press to open the Colour menu. The blue highlight moves to the first item in the menu. • Notes on Colour and Global Colourimetry Global Colourimetry menu (see later in this section, in Setup menu) After a calibration check on the projector or venue, a set of Global colour settings can be made in the Global Colourimetry menu. These settings are then available to be copied at any time using the Colour Mode setting in the Colour menu, or used as a starting point using the Trim feature in the Colour menu. Colour menu (see this section). The settings made in the Colour menu will be automatically saved in the Mode History, or can be manually saved to one of the Input Presets (see Input modes and settings earlier in this section). The selections available in Colour Mode in the Colour menu are: Global Copies the settings made in the Global Colourimetry menu Temperature Set the colour temperature using the slider User Set the Red, Green and Blue Lift and Gain using the sliders Peak Preset high brightness setting Video, Film, Graphic Applies the factory set P7 settings ColorMAX User Applies the User gamma settings made externally using the DP Userware on a personal computer
Rev C August 2009 Page 4.29 Digital Projection TITAN sx+600/700. User Manual 4. Controlling the projector Notes Read the notes on Colour and Global Colourimetry earlier in this section before making any settings in the Colour menus. Note that any changes made in the Global Colourimetry menu (see Setup Menu, later in this section) will affect ALL inputs, modes and presets for which Global Mode has been selected in the Colour menu. The Colour Temperature slider is available only if Temperature Mode is selected. The RGB Lift and Gain sliders are available only if User Mode is selected. The Component Type selection is available for RGB1 and Component inputs only. Colour Mode Press and to select Colour Mode. Press and to select from: Global Temperature User Peak Video Film Graphic ColorMAX User 1 ColorMAX User 2 Colour Temperature Press and to select Temperature. Press and to adjust the slider (3,000K to 10,000K. in 100 steps). RGB Lift Press and to select the parameter to be adjusted. Press and to adjust the slider. RGB Gain Press and to select the parameter to be adjusted. Press and to adjust the slider. Component Type Press and to select Component Type. Press and to select from: RGB YPrPb • • • • • Colour menu continued
Page 4.30 Rev C August 2009 4. Controlling the projector Digital Projection TITAN sx+600/700. User Manuall Notes The Trim submenu is available only if Global Colour Mode is selected. Colour Menu Trim Read the notes on Colour and Global Colourimetry earlier in this section before making any settings in the Colour menus. Trim Press and to select Trim. Press to open the Trim submenu. Trim rGB Lift and Gain Press and to select the parameter to be adjusted. Press and to adjust the slider (-128 to +127). Global Colourimetry This is a shortcut to the Global Colourimetry submenu, described later in this section, in Setup Menu. Press and to select Global Colourimetry. Press to open the Global Colourimetry submenu. • • • Colour menu continued
Rev C August 2009 Page 4.31 Digital Projection TITAN sx+600/700. User Manual 4. Controlling the projector Notes When using the menus, press OSD or to hide or reveal the On-Screen-Display. Setup Menu Setup menu To return to the main menu, press up to three times. From the main menu: Press and until Setup is highlighted. Press to open the Setup menu. The blue highlight moves to the first item in the menu. •
Page 4.32 Rev C August 2009 4. Controlling the projector Digital Projection TITAN sx+600/700. User Manuall Projector Press and to select Projector. Press to open the Projector submenu. Orientation Press and to select Orientation. Press and to select from: Desktop Front Desktop Rear Ceiling Front Ceiling Rear Control panel Backlight Press and to select Backlight. Press and to select from: On Off Component Video Sync Press and to select Component Video Sync. Press and to select from: Sync On Green Separate • • • • Setup menu, continuedNotes Setup Menu Projector
Rev C August 2009 Page 4.33 Digital Projection TITAN sx+600/700. User Manual 4. Controlling the projector Keystone Used to correct for distortion caused by the projector being mounted higher or lower than the screen. Press and to select Keystone. Press and to adjust the slider (-128 to +127). Lens Calibration Calibrate Focus Press and to select Calibrate Focus. Press . The focus mechanism will operate for about a minute, whilst the minimum and maximum travel distances are determined. Calibrate Zoom Press and to select Calibrate Zoom. Press . The zoom mechanism will operate for about a minute, whilst the minimum and maximum travel distances are determined. • • • Setup menu, projector continuedNotes Each time a new lens is fitted to the projector, the calibration procedure must be carried out.
Page 4.34 Rev C August 2009 4. Controlling the projector Digital Projection TITAN sx+600/700. User Manuall Notes Setup Menu Test Pattern Test pattern Press and to select Test Pattern. Press to open the Test Pattern submenu. Press and to select from: Off Alignment Grid Screen Layout (shows outlines of various aspect ratios) Chequerboard Colour Bars 0% Field (black) ColorMAX Calibration 100% Field (Corrected White) (white, affected by colour settings) 100% Field (Peak White) (white, unaffected by colour settings) • Setup menu continued
Rev C August 2009 Page 4.35 Digital Projection TITAN sx+600/700. User Manual 4. Controlling the projector Notes Setup Menu Global Colourimetry Some menu items may be greyed out - unavailable due to the effect of settings made in other menus, or due to the type of input signal. Read these notes on Colour and Global Colourimetry before making any settings in the Colour menus. Note that any changes made in the Global Colourimetry menu will affect ALL inputs, modes and presets for which Global Mode has been selected in the Colour menu (see Colour Menu, earlier in this section). Global Colourimetry Press and to select Global Colourimetry. Press to open the Global Colourimetry submenu. • • Setup menu continued Notes on Colour and Global Colourimetry Global Colourimetry menu (see this section) After a calibration check on the projector or venue, a set of Global colour settings can be made in the Global Colourimetry menu. These settings are then available to be copied at any time using the Colour Mode setting in the Colour menu, or used as a starting point using the Trim feature in the Colour menu. Colour menu (see earlier in this section). The settings made in the Colour menu will be automatically saved in the Mode History, or can be manually saved to one of the Input Presets (see Input modes and settings earlier in this section). The selections available in Colour Mode in the Colour menu are: Global Copies the settings made in the Global Colourimetry menu Temperature Set the colour temperature using the slider User Set the Red, Green and Blue Lift and Gain using the sliders Peak Preset high brightness setting Video, Film, Graphic Applies the factory set P7 settings ColorMAX User Applies the User gamma settings made externally using the DP Userware on a personal computer
Page 4.36 Rev C August 2009 4. Controlling the projector Digital Projection TITAN sx+600/700. User Manuall Notes Read the notes on Colour and Global Colourimetry earlier in this section before making any settings in the Colour menus. Note that any changes made in the Global Colourimetry menu will affect ALL inputs, modes and presets for which Global Mode has been selected in the Colour menu (see Colour Menu, earlier in this section). The Colour Temperature slider is available only if Temperature Mode is selected. The RGB Lift and Gain sliders are available only if User Mode is selected. Colour Mode Press and to select Colour Mode. Press and to select from: Temperature User Peak Video Film Graphic ColorMAX User 1 ColorMAX User 2 Colour Temperature Press and to select Temperature. Press and to adjust the slider (3,000K to 10,000K. in 100 steps). rGB Lift Press and to select the parameter to be adjusted. Press and to adjust the slider. rGB Gain Press and to select the parameter to be adjusted. Press and to adjust the slider. • • • • Setup menu, Global Colourimetry continued