Digital Projection Titan Sx+600, Sx+700 User Manual

							
Rev C August 2009 Page 4.7
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Indicators
Input status indicators
The indicator next to each input connector on the input panel will light as follows:
 off = input not selected
  green
 = input selected, signal detected and in range
 flashing green  = input selected, but signal not detected or out of range
Notes
 There are more indicators on 
the Control panel, and these are 
described on the next page.
5. Composite Video
6. S-Video
7. Component
1. RGB1
2. RGB2
3. DVI4. SDI 
						

							
Page 4.8  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

The control panel
Keypad layout
The controls on the keypad are identical to those at the top of the remote control, 
and are described on the following pages.
Projector status indicators
The indicators on the control panel are as follows:
Power off = NO POWER
 green = normal RUNNING mode amber = STANDBY mode
Shutter amber = CLOSED green = OPEN
Error off = NO ERROR
 flashing  = ERROR (temperature) steady = ERROR (voltage)
IR 
blue flash = Remote control command received
Lamp 1 off = OFF
  flashing red  = LAMP ERROR 
green = ON (100%) amber = (80 - 99%)
 flashing green  = LAMP WARM-UP    flashing amber  = COOL-DOWN
Lamp 2 off = OFF
 flashing red  = LAMP ERROR green = ON (100%) amber = (80 - 99%)
 flashing green  = LAMP WARM-UP    flashing amber  = COOL-DOWN
Notes
 Many features are controlled 
from the menus using the menu 
navigation keys on the remote 
control or keypad.
 For more information about 
using the menus, see later in 
this section, Using the menus.
 Some of the menu features, for 
example brightness, contrast 
and input preset operations, can 
be accessed directly using the 
control keys at the bottom of 
the remote control.
  Other features, eg zoom and 
focus, are controlled using the 
control keys at the top of the 
remote control and keypad.
 For more information about 
using the control keys, see 
later in this section, Using the 
control keys. 
						

							
Rev C August 2009 Page 4.9
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

The remote control
Layout
Timeout
There is a 10 second timeout for the three Lens adjustment keys (see note on next 
page).
There is a separate, adjustable timeout for the On Screen Menus (see On Screen 
Display, in Setup Menu, later in this section).
Notes
 Many features are controlled 
from the menus using the menu 
navigation keys on the remote 
control or keypad.
 For more information about 
using the menus, see later in 
this section, Using the menus.
 Some of the menu features, for 
example brightness, contrast 
and input preset operations, can 
be accessed directly using the 
control keys at the bottom of 
the remote control.
  Other features, eg zoom and 
focus, are controlled using the 
control keys at the top of the 
remote control and keypad.
 For more information about 
using the control keys, see 
later in this section, Using the 
control keys.
 The following keys are NOT 
used on this projector:
 CTRL 
R P Y 
FUNC 
10+   (but N is used) 
#   (but R is used)
 Note that plugging in the remote 
control cable will disable the 
infra-red.
Menu 
navigation 
keys
Remote control 
backlight 
ON/OFF
Control keys
Transmit 
indicator 
						

							
Page 4.10  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 Closing the shutter produces 
a better black than simply 
removing the signal, as the 
light source will be completely 
blocked by the shutter blade.
 When the OSD is OFF:
  -  all menu navigation keys are 
disabled.
  - keys such as 
 BrI 
(brightness) will still function, 
but the slider bars will not be 
visible on screen.
  When any of the three Lens 
adjustment keys is pressed, the 
blue Transmit indicator on the 
remote control will light for 10 
seconds:
  - after 10 seconds, if no 
adjustment has been made, 
the indicator will go out and 
the Lens adjustment key must 
be pressed again to resume 
adjustment.
  - to end the adjustment before 
10 seconds has elapsed, press 
the   key.
  - all other adjustments will 
be locked out until the Lens 
adjustment is ended.
 For more information about the 
amount of lens shift available, 
see  section 2. Installation.
Using the control keys
Power
Press POWER  and hold for 3 seconds, to switch the projector ON.
Press POWER  and hold for 3 seconds, to switch the projector OFF.
Shutter
Press SHUTTER  to OPEN the shutter.
Press SHUTTER  to CLOSE the shutter.
On-Screen-Display
Press OSD  to switch the On-Screen-Display OFF.
  This includes ALL menus, controls and on-screen messages.
Press OSD  to switch the On-Screen-Display ON.
Focus
Press  followed by  and  to adjust the focus.
When adjustment is finished, press .
Zoom
Press  followed by  and  to adjust the zoom.
When adjustment is finished, press .
Shift
Press  followed by , ,  or  to shift the lens up, down, left or 
right.
When adjustment is finished, press .
•
•
•
•
•
•
•
•
• 
						

							
Rev C August 2009 Page 4.11
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Auto-detect input mode
Press  to force the projector to re-detect the input mode 
(see Input modes and settings, earlier in this section).
Source information
Press  to display the source information screen.
Input
Press  or   to change to the next input up or down the following list:
1. RGB1
2. RGB2
3. DVI
4. SDI
5. Composite Video
6. S-Video
7. Component
Or press the numbered keys 1–7 to change directly to the input:
 
•
•
•
•
Notes
 For more information about 
input mode detection, see 
earlier in this section, Input 
modes and settings. 
						

							
Page 4.12  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 For more information about 
input modes and input presets, 
see earlier in this section, Input 
modes and settings.
  See also 
Input menu, later in 
this section.
 A preset can be applied only to 
the same mode for which it was 
created. If the detected input 
mode does not match, then 
settings from the mode history 
or mode library will be applied.
  For more information about 
input modes, see Input modes 
and settings. earlier in this 
section.
 The lens settings, ie Focus 
position, Zoom position and 
Shift, are included only for the 
first ten presets.
Input Presets
recall
To recall a set of modal and lens settings that have been saved, press and hold 
, whilst pressing the lettered key  A – S.
  The projector will switch to the saved input source, and redetect  the input mode 
before applying the saved modal and lens settings.
Save
To save the current input source, modal and lens settings, press and hold , 
whilst pressing the lettered key  A – S.
  If this Preset has been used before, and the Input source has be en changed, 
then the following  message will be displayed.
 Press 
 and   to select either OK or Cancel.
  Press 
 to confirm your selection.
The settings will be saved to the selected preset, and the following message will 
be displayed.
•
•
•
•
•
• 
						

							
Rev C August 2009 Page 4.13
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 The red, green and blue keys 
are disabled when the OSD is 
switched OFF.
 For more information about test 
patterns, see Setup menu, later 
in this section.
 The Saturation control is 
available for Composite, S-
Video and Component inputs 
only.
 The Phase control is available 
for RGB inputs only.
 For all adjustments on this page 
that require more than one key 
to be pressed:
  - after 10 seconds, if no 
adjustment has been made,  the  
 key must be pressed again 
to resume adjustment.
  - to end the adjustment before 
10 seconds has elapsed, press 
a different adjustment key, or 
press the   key.
 When the OSD is OFF:
  - the 
 keys will still function, 
but the controls will not be 
visible on screen.
Red, Green and Blue
Press ,  or   to switch the red, green or blue components OFF 
or ON.
Test pattern
Press  to select a test pattern.
Picture settings
Press a  key, followed by  and   to adjust these picture settings:
Brightness   
 BRI
Contrast   
 CON
Saturation   
 SAT
Phase   
 PHASE
Aspect ratio   
 ASPECT
Geometry settings
Keystone adjustment is used to correct for distortion caused by the projector being 
mounted higher or lower than the screen.
Press Keystone 
 KEYST,
followed by  and  to adjust the keystone correction:
Press Position  
 POS,
followed by , ,  and  to adjust the picture position, for images 
smaller than the DMD:
•
•
•
•
• 
						

							
Page 4.14  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Notes
 The magnify feature utilises a 
digital zoom. Used with the pan 
control, this can be used to:
  - enlarge a section of the image
  - enable the use of multiple 
projectors to construct a large 
image from tiles.
 The pan control is available 
only when the image has been 
magnified.
 If the OSD moves off screen 
due to a change in image size, 
then pressing the size key will 
restore its readability.
 When fresh batteries are 
inserted in the remote control 
it will default to address 00. 
Remote control 00 is a master 
control,  able to control all 
projectors.
  If two or more projectors are set 
to the same address, they can 
be controlled from one remote 
control, provided they are 
connected by cable or in range 
of the infra red.
Magnify and pan
Press Magnify  MAGNIFY
followed by  and  to adjust the size of the picture.
Press Pan   
 PAN
followed by , ,  and  to adjust the position of the magnified image.
On-screen-display size
Press Size    SIZE
to switch the size of the OSD between large and small.
Remote control address
The projector and the remote control need to be set to matching addresses. Read 
the note to the right on this page, and follow the instructions in the order shown 
below:
1   Set the projector address as shown in Setup menu, later in this section.
2  Set the remote control address:
Press and hold  
whilst pressing two numbered keys  0 – 9
to set the remote control address to any number between 00 and 99. 
(leading zeros must be used for numbers less than 10)
Remote control backlight
Press  to switch the backlight on and off.
•
•
•
•
• 
						

							
Rev C August 2009 Page 4.15
Digital Projection TITAN sx+600/700. User Manual  4. Controlling the projector

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When the OSD is OFF, all menu 
navigation keys will be disabled.
  When the OSD is switched back 
ON, the menus will remain OFF 
until the   key is pressed 
again. The menus will then 
reopen at the same point they 
were last viewed.
 If a menu is opened, and no 
other key is pressed within the 
period set in the OSD Timeout 
menu, then the menus will 
disappear. When the   key 
is pressed again, the menus will 
reopen at the same point they 
were last viewed.
  (see 
On Screen Display, 
in Setup Menu, later in this 
section).)
 
Main menu: Input
 SDI not present on earlier 
models
 
Main menu: Setup
Using the menus
Navigating menus and submenus
When the menus are in use and the OSD is ON, the top level menu headings are 
always visible to the left of the screen.
Each menu item can lead to a number of submenus, which are displayed in the 
column to the right . The  symbol indicates that a submenu is available.
Each submenu can lead to further submenus, up to a maximum of three levels.
To display the menus, press  on the remote control or the keypad.
  The menus will always open at the same point they were last viewed. The 
example below shows the first menu display following power on – the item that is 
currently selected (the Input menu) is highlighted in blue.
To select a menu, press  and , for example the Setup menu:
•
•
•
Input
Picture
Geometry
Colour
Setup
Information
1.RGB1
2.RGB2
3.DVI
4.SDI
5.CompositeVideo
6.S-Video
7.Component
Presets 
						

							
Page 4.16  Rev C August 2009
4. Controlling the projector  Digital Projection TITAN sx+600/700. User Manuall

Press  to open the menu. The blue highlight moves to the first item in the 
menu, which may be submenu, for example the Projector Setup submenu.
To select a submenu, press  and  , for example the Lamp submenu. 
Press  to open the submenu. The submenu opens, with the title at the top.
To close the submenu and return to the previous level, press .
There may be up to three levels of submenu, so to return to the top level, you 
may have to press  up to three times.
To close the menu display completely, press .
•
•
•
•
•
Notes
 
Setup menu
 
Setup menu 
  Lamp
 
Setup menu