Digital Projection Titan Sx+600, Sx+700 User Manual

Rev C August 2009 Page 6.3
Digital Projection TITAN sx+600/700. User Manual  6. Maintenance

Changing	the	air	filter
Turn the power OFF and allow the lamp to cool for 5 minutes.
Unscrew the four captive finger screws securing the rear door - the door is 
tethered, so cannot be removed completely.
Pull out both air filters.
Fit two new air filters, making sure that they are each the correct way around, as 
shown below.
Re-fit the rear door, making sure that the door tether is not trapped, and tighten...

Page 6.4  Rev C August 2009
6. Maintenance  Digital Projection TITAN sx+600/700. User Manuall
Notes
 Never use strong detergents 
or solvents such as alcohol 
or thinners to clean the 
projector and lens.
 NEVER touch the lamp or 
reflector.
Cleaning
Turn the projector off before cleaning.
Projector
Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild 
detergent.
Lens
Use a blower or lens paper to clean the lens, taking care not to scratch the glass.
Lamp module
Use a blower...

Rev C August 2009  Page 7.1
7. Appendix
Contents
Troubleshooting ..................................................................................................................................7.2
Specifications ......................................................................................................................................7.4
Part numbers ....................................................................................................................................7.4
Optical...

Page 7.2  Rev C August 2009
7. Appendix  Digital Projection TITAN sx+600/700. User Manuall

Troubleshooting
problempossible solutions
The projector will not power up.Check that the mains plug is plugged in and that the mains supply is swi\
tched on.
Check any external fuses or breakers.
The projector shuts down after it has 
been in use for some time.
The projector may be overheating. Check that the air inlets and outlets are clear 
of any obstruction. Check that the air filter is clean, and if it is...

Rev C August 2009 Page 7.3
Digital Projection TITAN sx+600/700. User Manual  7. Appendix

problempossible solutions
Projector does not respond to control 
commands from a computer.
Check that the LAN or serial cable is connected correctly.
See this section 7. Appendix, Connections
If using a LAN, check that the address setting is made correctly .
See section 4. Controlling the projector, Network menu
If using a serial cable, check that the baud rate is set correctly.
See this section 7. Appendix,...

Page 7.4  Rev C August 2009
7. Appendix  Digital Projection TITAN sx+600/700. User Manuall

Specifications
Part numbers
Projector
sx+600 107-692
sx+700  107-770
Rigging frame  107-956
Power cable 10A, Europe  102-163
Power cable 13A, North America  102-165
Power cable 10A, United Kingdom  102-180
Remote control  105-023
4x AAA batteries  105-922
Remote cable 5m  102-162
User manual on CD  105-923
Important Information  108-467
Replacement parts
Single 300W Lamp module + air filter 107-694
Two 300W Lamp...

Rev C August 2009 Page 7.5
Digital Projection TITAN sx+600/700. User Manual  7. Appendix

Electrical
Inputs  RGB1, RGB2, DVI, SDI, Composite Video, S-Video, Component
Pixel clock  up to 165MHz
Control inputs  1 x LAN
  1 x wifi LAN
  1 x RS232 serial: 19200 baud, 8 bits, 1 stop bit, no parity
  1 x remote control
Mains voltage  100-230 VAC ±10%, 48-62Hz (single phase)
Power consumption
sx+600  850 W
sx+700  950W
International Regulations Meets FCC Class A  requirements 
Meets EMC Directives (EN 55022,...

Page 7.6  Rev C August 2009
7. Appendix  Digital Projection TITAN sx+600/700. User Manuall

lens extension, measured from 
front of corner post* Actual available lens shift is reduced when the lens is to be sh ifted 
in two directions combined (see Shifting the image, in section 
2. Installation
).
**  Lens extension is the distance from the outer end of the lens to the 
front of the projector. It is important for calculating throw distance 
accurately (see Useful lens calculations, in section 2....

Rev C August 2009 Page 7.7
Digital Projection TITAN sx+600/700. User Manual  7. Appendix

lens extension, measured from 
front of corner post* Actual available lens shift is reduced when the lens is to be sh ifted 
in two directions combined (see Shifting the image, in section 
2. Installation
).
**  Lens extension is the distance from the outer end of the lens to the 
front of the projector. It is important for calculating throw distance 
accurately (see Useful lens calculations, in section 2....

Page 7.8  Rev C August 2009
7. Appendix  Digital Projection TITAN sx+600/700. User Manuall

Dimensions
All dimensions in mm 
unless otherwise stated