Digital Projection Titan 1080p-600, Reference 1080p, Titan 1080p-700, 1080p Ultra Contrast User Manual

Rev C August 2009 Page 4.35
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Notes
 
Setup Menu 
  Test Pattern
Test pattern
Press  and   to select Test Pattern.
  Press 
 to open the Test Pattern submenu.
  Press 
 and   to select from:
Off
Alignment Grid
Screen Layout     (shows outlines of various aspect ratios)
Chequerboard
Colour Bars
0% Field      (black)
ColorMAX Calibration
100% Field (Corrected White)  (white, affected by colour...

Page 4.36  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 
Setup Menu 
  Global Colourimetry
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Read these notes on Colour 
and Global Colourimetry 
before making any settings in 
the Colour menus.
  Note that any changes made in 
the Global Colourimetry menu 
will affect ALL inputs,...

Rev C August 2009 Page 4.37
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Notes
 Read the notes on Colour and 
Global Colourimetry earlier 
in this section before making 
any settings in the Colour 
menus.
  Note that any changes made in 
the Global Colourimetry menu 
will affect ALL inputs, modes 
and presets for which Global 
Mode has been selected in 
the Colour menu (see Colour 
Menu, earlier in this section).
 The Colour Temperature...

Page 4.38  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Lamp
Press  and   to select Lamp.
  Press 
 to open the Lamp submenu.
The middle row shows the current lamp setting.
Change Lamp Setting
Press  and   to select Change Lamp Setting.
Press  to open the Lamp Setting control box.
•
•
Notes
 
Setup Menu 
  Lamp
Setup menu, continued
continued 

Rev C August 2009 Page 4.39
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Notes
 In single lamp modes:
  - if the running lamp fails, the 
other lamp will automatically be 
switched on.
 The selected lamp mode:
  - will not be applied until 
OK is 
selected
  - will be applied gradually over a 
period of 30 seconds
  - will not be applied until the end 
of any warm-up or cool-down 
period that has already started.
Lamp power
Press  and   to...

Page 4.40  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 
Setup Menu 
  On Screen Display
 The On Screen Display will 
move to the centre of the DMD 
when Blanking is turned On.
  (see 
Geometry menu, earlier in 
this section).
 If a menu is opened, and no 
other key is pressed within the 
period set in the OSD Timeout 
menu, then the menus will 
disappear. When the   key 
is pressed again, the menus will 
reopen at...

Rev C August 2009 Page 4.41
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Password
Entry to the password protected area is available to authorised service personel 
only.
Press  and   to select Password.
  Press 
 to open the Password control box.
Press  and   to select each digit in turn.
  Press 
 and   to adjust the digit from:
0 to 9
 then move to the next digit.
  Use 
 and   to select from
OK
 Press  
 to enter the password controlled...

Page 4.42  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 
Setup Menu 
  Comunication
 When fresh batteries are 
inserted in the remote control, 
it will default to address 00. 
Remote control 00 is a master 
control,  able to control all 
projectors.
  If two or more projectors are set 
to the same address, they can 
be controlled from one remote 
control, provided they are 
connected by cable or in range 
of the...

Rev C August 2009 Page 4.43
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Notes
 
Setup Menu 
  Network
 Some items may be greyed out 
or not editable, due to the effect 
of other settings made in the 
Network submenu.
  For example, if a 
Wired 
Connection is selected:
  Wifi, Channel and SSID will be 
unavailable.
Setup menu continued
Network
Press  and   to select Network.
  Press 
 to open the Network submenu.
MAC Address
Projector’s...

Page 4.44  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 IP Address cannot be changed 
if DHCP is set to ON.
  DHCP will set the the address, 
which will be displayed for 
information only.
Setup menu, Network continued
DHCp
Press  and   to select DHCP
  Press 
 to open the DHCP control box.
  Press 
 and   to select from:
On
Off
 Press  
 to apply the new DHCP setting.
Ip  Address
Press  and   to select IP Address...