Digital Projection Titan 1080p-600, Reference 1080p, Titan 1080p-700, 1080p Ultra Contrast User Manual

							
Rev C August 2009 Page 4.35
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Notes
 
Setup Menu 
  Test Pattern
Test pattern
Press  and   to select Test Pattern.
  Press 
 to open the Test Pattern submenu.
  Press 
 and   to select from:
Off
Alignment Grid
Screen Layout     (shows outlines of various aspect ratios)
Chequerboard
Colour Bars
0% Field      (black)
ColorMAX Calibration
100% Field (Corrected White)  (white, affected by colour settings)
100% Field (Peak White) 
(white, unaffected by colour settings)
•
Setup menu, projector continued 
						

							
Page 4.36  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 
Setup Menu 
  Global Colourimetry
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 Read these notes on Colour 
and Global Colourimetry 
before making any settings in 
the Colour menus.
  Note that any changes made in 
the Global Colourimetry menu 
will affect ALL inputs, modes 
and presets for which Global 
Mode has been selected in 
the Colour menu (see Colour 
Menu, earlier in this section).
Global Colourimetry
Press  and   to select Global Colourimetry.
Press  to open the Global Colourimetry submenu.
•
•
Setup menu continued
  Notes on Colour and Global Colourimetry
Global Colourimetry menu (see this section)
After a calibration check on the projector or venue, a set of Global colour settings 
can be made in the Global Colourimetry menu. These settings are then available 
to be copied at any time using the Colour Mode setting in the Colour menu, or 
used as a starting point using the Trim feature in the Colour menu.
Colour menu (see earlier in this section).
The settings made in the Colour menu will be automatically saved in the Mode 
History, or can be manually saved to one of the Input Presets (see Input modes 
and settings earlier in this section).
The selections available in Colour Mode in the Colour menu are:
Global  Copies the settings made in the Global Colourimetry menu
Temperature  Set the colour temperature using the slider
User   Set the Red, Green and Blue Lift and Gain using the sliders
Peak  Preset high brightness setting
Video, Film,
Graphic  Applies the factory set P7 settings
ColorMAX User  Applies the User gamma settings made externally using the 
DP Userware on a personal computer 
						

							
Rev C August 2009 Page 4.37
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Notes
 Read the notes on Colour and 
Global Colourimetry earlier 
in this section before making 
any settings in the Colour 
menus.
  Note that any changes made in 
the Global Colourimetry menu 
will affect ALL inputs, modes 
and presets for which Global 
Mode has been selected in 
the Colour menu (see Colour 
Menu, earlier in this section).
 The Colour Temperature 
slider is available  only if 
Temperature Mode is selected.
 The RGB Lift and Gain sliders 
are available  only if User Mode 
is selected.
Colour Mode
Press  and   to select Colour Mode.
  Press 
 and   to select from:
Temperature
User
Peak
Video
Film
Graphic
ColorMAX User 1
ColorMAX User 2
Colour Temperature
Press  and   to select Temperature.
  Press 
 and   to adjust the slider (3,000K to 10,000K. in 100 steps).
rGB Lift
Press  and   to select the parameter to be adjusted.
  Press 
 and   to adjust the slider.
rGB Gain
Press  and   to select the parameter to be adjusted.
  Press 
 and   to adjust the slider.
•
•
•
•
Setup menu, Global Colourimetry continued 
						

							
Page 4.38  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Lamp
Press  and   to select Lamp.
  Press 
 to open the Lamp submenu.
The middle row shows the current lamp setting.
Change Lamp Setting
Press  and   to select Change Lamp Setting.
Press  to open the Lamp Setting control box.
•
•
Notes
 
Setup Menu 
  Lamp
Setup menu, continued
continued 
						

							
Rev C August 2009 Page 4.39
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Notes
 In single lamp modes:
  - if the running lamp fails, the 
other lamp will automatically be 
switched on.
 The selected lamp mode:
  - will not be applied until 
OK is 
selected
  - will be applied gradually over a 
period of 30 seconds
  - will not be applied until the end 
of any warm-up or cool-down 
period that has already started.
Lamp power
Press  and   to select the Lamp Power setting.
  Press 
 and   to adjust the Lamp Power from:
  80 to 100%  in 1% steps
Lamp Mode
Press  and   to select Lamp Mode.
  Press 
 and   to select from:
single lamp modes
Lamp 1  lamp 1 only
Lamp 2  lamp 2 only
Alternate  on power up, selects the lamp with the least hours used
dual lamp mode
Lamps 1 and 2  both lamps
OK
Press  and   to select OK.
  Press  
 to apply the new settings.
Cancel
Press  and   to select Cancel.
  Press  
 or   to exit without applying the new settings.
The indicators on the control panel will show as follows:
Lamp 1 off = OFF
  flashing red  = LAMP ERROR 
green = ON (100%) amber = (80 - 99%)
 flashing green  = LAMP WARM-UP    flashing amber  = COOL-DOWN
Lamp 2 off = OFF
 flashing red  = LAMP ERROR green = ON (100%) amber = (80 - 99%)
 flashing green  = LAMP WARM-UP    flashing amber  = COOL-DOWN
•
•
•
•
Setup menu, Lamp continued 
						

							
Page 4.40  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 
Setup Menu 
  On Screen Display
 The On Screen Display will 
move to the centre of the DMD 
when Blanking is turned On.
  (see 
Geometry menu, earlier in 
this section).
 If a menu is opened, and no 
other key is pressed within the 
period set in the OSD Timeout 
menu, then the menus will 
disappear. When the   key 
is pressed again, the menus will 
reopen at the same point they 
were last viewed.
On Screen Display
Press  and   to select On Screen Display.
  Press 
 to open the On Screen Display submenu.
OSD position
Press  and   to select OSD Position
  Press 
 and   to select from:
Upper Left
Upper Centre
Upper Right
Middle Left
Middle Centre
Middle Right
Lower Left
Lower Centre
Lower Right
OSD Size
Press  and   to select OSD Size.
  Press 
 and   to select from:
Large
Small
OSD Timeout
Press  and   to select the length of the On Screen Display Timeout.
  Press 
 and   to select from:
  0 to 255  in 1 second steps 
(when set to zero, the OSD never times out)
•
•
•
•
Setup menu continued 
						

							
Rev C August 2009 Page 4.41
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Password
Entry to the password protected area is available to authorised service personel 
only.
Press  and   to select Password.
  Press 
 to open the Password control box.
Press  and   to select each digit in turn.
  Press 
 and   to adjust the digit from:
0 to 9
 then move to the next digit.
  Use 
 and   to select from
OK
 Press  
 to enter the password controlled area.
or  Cancel
Press   or   to exit without applying the password.
•
•
NotesSetup menu continued 
						

							
Page 4.42  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 
Setup Menu 
  Comunication
 When fresh batteries are 
inserted in the remote control, 
it will default to address 00. 
Remote control 00 is a master 
control,  able to control all 
projectors.
  If two or more projectors are set 
to the same address, they can 
be controlled from one remote 
control, provided they are 
connected by cable or in range 
of the infra red.
Communication
Press  and   to select Comunication.
  Press 
 to open the Comunication submenu.
projector Address
The projector and the remote control need to be set to matching addresses. Read 
the note to the right on this page, and follow the instructions in the order shown 
below:
1   Set the projector address:
Press  to open the Projector address control box.
Press  and   to select the address setting.
  Press  
 and    to adjust the address from:
00 to 99
 Use 
 and   to select from
Apply
 Press  
 to apply the new Projector Address.
or  Cancel
Press   or   to exit without making the change.
2  Set the remote control address as shown in Using the control keys, earlier in 
this section.
•
Setup menu continued 
						

							
Rev C August 2009 Page 4.43
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Notes
 
Setup Menu 
  Network
 Some items may be greyed out 
or not editable, due to the effect 
of other settings made in the 
Network submenu.
  For example, if a 
Wired 
Connection is selected:
  Wifi, Channel and SSID will be 
unavailable.
Setup menu continued
Network
Press  and   to select Network.
  Press 
 to open the Network submenu.
MAC Address
Projector’s unique ID  - for information only - cannot be changed.
Connection
Press  and   to select Connection
  Press 
 to open the Connection control box.
  Press 
 and   to select from:
Wired
Wireless
 Press  
 to apply the new Connection setting.
•
•
• 
						

							
Page 4.44  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 IP Address cannot be changed 
if DHCP is set to ON.
  DHCP will set the the address, 
which will be displayed for 
information only.
Setup menu, Network continued
DHCp
Press  and   to select DHCP
  Press 
 to open the DHCP control box.
  Press 
 and   to select from:
On
Off
 Press  
 to apply the new DHCP setting.
Ip  Address
Press  and   to select IP Address
  Press 
 to open the IP Address control box.
  Use 
 and   to select each number in turn.
  Use 
 and   to adjust the number
  then move to the next number.
  Use 
 and   to select from
Apply
 Press  
 to apply the new IP Address.
or  Cancel
Press   or   to exit without making the change.
•
•