Digital Projection Titan 1080p-600, Reference 1080p, Titan 1080p-700, 1080p Ultra Contrast User Manual

							
Rev C August 2009 Page 5.3
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual   5. Userware

Notes
 To use the Titan Userware the 
java Runtime Environment
 
software must be installed on 
your browser. This software can 
be downloaded, free of charge 
from www.java.com.
  The LAN IP Address of the 
projector can be found in the 
Network submenu of the Setup 
menu, as described in section 
4. Controlling the projector
.
 Whenever the projector is 
connected to mains power, 
whether in Running mode or 
Standby mode, the Applet 
version of the Userware will be 
available.
 The Applet version of the 
Userware can be used only to 
control the projector from which 
it was downloaded.
 The Userware can be used to 
control only one projector at a 
time, and only one instance can 
be running at one time.
  More than one computer can be 
used to control more than one 
projector on the same network.
Introduction
The Titan Userware provides an intuitive interface to enable control of many of the 
features of the projector from a personal computer, via a LAN connection.
There are two versions of the Userware: the Applet version, stored on the projector 
and the Standalone version, supplied on disk or from the Digital Projection website.
Applet version
To activate the Userware, simply point the browser at the projector by typing its 
LAN IP Address
 into the address bar, then press the Enter key or click on Go.
The Applet version does not require installation on the personal computer, as it 
is in the form of a Java applet, downloaded automatically from the projector by 
the browser. The first time the applet is downloaded, you may see the following 
message:
Tick the box and click OK. In future, the Userware will load immediately.
The Userware interface is organised into a number of pages, as listed below:
Show  Lens        Image   Screen
MCGD  TCGD        Global   Modal
Info        System
Each page is described in full later in this section.
When the Userware is started, the Show page will display immediately. The Page 
buttons are always visible at the bottom of the display:
Disconnect
Click on Disconnect to disconnect from the projector.
reconnect
To reconnect, click on the browser’s Refresh button,
  or re-type the 
IP Address in the browser address box then press Return.
•
•
•
•
New Java applet download:
Tick the box only if you trust the source.
o  I trust this applet.         OK 
						

							
Page 5.4  Rev C August 2009
5. Userware  Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Standalone version
To install the Userware, simply copy the file (from the CD, or downloaded from 
the Digital Projection website), to a folder on the computer.
Double click on the filename to start the software.
The Userware interface is organised into a number of pages, as listed below:
Show  Lens        Image   Screen
MCGD  TCGD        Global   Modal
info        System   Discover
Each page is described in full later in this section.
When the Userware is started, the Show page will display immediately. The Page 
buttons are always visible at the bottom of the display:
Disconnect
Click on Disconnect to disconnect from the projector.
reconnect
To reconnect, click on the Discover button. The Discover page is described in 
more detail later in this section.
•
•
•
•
Notes
 To use the Titan Userware the 
java Runtime Environment
 
software must be installed on 
your computer. This software 
can be downloaded, free of 
charge from www.java.com.
  The Userware can be used to 
control only one projector at a 
time, and only one instance can 
be running at one time.
  The 
Discover page can be 
used to switch control between 
multiple projectors. 
(see later in this section)
  More than one computer can be 
used to control more than one 
projector on the same network. 
						

							
Rev C August 2009 Page 5.5
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual   5. Userware

Show page
The Show page is the first to display when the browser connects to the projector .
To return to the Show page at any time, click on Show.
On / Off
Click On to switch the projector On.
Click Off to switch the projector into Standby mode.
Shutter Open / Closed
Click on Shutter O to open the shutter.
Click on Shutter C to close the shutter.
Freeze / Un-Freeze
Click on Freeze to freeze the display on the current frame.
Click on Un-Freeze to un-freeze the display.
Picture sliders
Use the sliders to adjust the Brightness, Contrast, Saturation, Hue and 
Sharpness of the display.
Click on the number above the slider to return to the default value.
•
•
•
•
•
•
•
•
•
Notes
Picture 
sliders 
						

							
Page 5.6  Rev C August 2009
5. Userware  Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Input Presets
recall
To recall a set of modal settings that have been saved:
Click on Preset, and select one of the Presets A - S, from the drop down menu.
Click on Recall.
  The projector will switch to the saved input source, and redetect  the input mode 
before applying the saved modal settings.
Save
To save the current input source, mode and modal settings:
Click on Preset, and select one of the Presets A - S, from the drop down menu.
Click on Save.
  The modal settings will be saved to the selected preset.
•
•
•
•
Notes
  For more information about 
input modes and input presets, 
see Input modes and settings, 
in section  4. Controlling the 
Projector.
 A preset can be applied only to 
the same mode for which it was 
created. If the detected input 
mode does not match, then 
settings from the mode history 
or mode library will be applied 
instead.
  For more information about 
input modes, see Input modes 
and settings, in section 
4. Controlling the Projector
.
Show page continued
Preset 
						

							
Rev C August 2009 Page 5.7
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual   5. Userware

Orientation
Click on Orientation to select one of the following from the drop down menu:
Desktop Front
Ceiling Front
Desktop Rear
Ceiling Rear
Input
Click on Input to select one of the following from the drop down menu:
RGB1
RGB2
DVI
SDI
Composite Video
S-Video
Component
•
•
Notes
 For more information about 
input modes, see Input modes 
and settings, in section 
4. Controlling the Projector.
Show page continued
Orientation
Input 
						

							
Page 5.8  Rev C August 2009
5. Userware  Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Test Pattern
Click on Test Pattern to select from the drop down menu:
Aspect Ratio
Click on Aspect Ratio to select from the drop down menu.
•
•
Show page continuedNotes
 For more information about 
test patterns, see Setup menu, 
in section  4. Controlling the 
Projector.
 For more information about 
aspect ratios, see Picture 
menu and Geometry menu, 
in section  4. Controlling the 
Projector.
Test 
PatternAspect 
Ratio 
						

							
Rev C August 2009 Page 5.9
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual   5. Userware

NotesLens page
To see the Lens page, click on Lens.
Lens controls
Click on the buttons to Move, Focus and Zoom the lens.
Click on Stop All Lens Movement to abort any unwanted lens control 
movement.
Shutter Open / Closed
Click on Shutter Open to open the shutter.
Click on Shutter Close to close the shutter.
•
•
•
•
•
Lens 
controls 
						

							
Page 5.10  Rev C August 2009
5. Userware  Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 The Component selection is 
available for the Component 
input only.
 For more information about 
phase, see Picture menu and 
Geometry menu, in section 
4. Controlling the Projector
.
  The Phase slider is available for 
RGB1 and RGB2 inputs only.
Image page
To see the Image page, click on Image.
Component
Click on Component to select one of the following from the drop down menu:
Component RGB
Component YUV
Phase slider
Use the slider to adjust the Phase.
•
•
•
ComponentPhase 
slider 
						

							
Rev C August 2009 Page 5.11
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual   5. Userware

Notes
Colour Space
Click on Colour Space to select one of the following from the drop down menu:
RGB
SMPTE240 YPrPb
REC709 YPrPb
REC601 YPrPb
SMPTE240 YCrCb
REC709 YCrCb
REC601 YCrCb
•
Image page continued
Colour 
Space 
						

							
Page 5.12  Rev C August 2009
5. Userware  Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 For more information about 
Gamma, see Picture menu, 
in section  4. Controlling the 
Projector.
 User download of Gamma 
correction tables is not yet 
available.
 The Parametric slider is 
available only when Parametric 
is selected in Gamma 
Correction.
Gamma
Click on Gamma Correction to select from the drop down menu:
Parametric slider
Use the slider to adjust the Gamma manually.
•
•
Image page continued
Parametric 
slider