Digital Projection Titan 1080p-600, Reference 1080p, Titan 1080p-700, 1080p Ultra Contrast User Manual

Rev C August 2009 Page 2.9
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual   2. Installation

Lens charts continued
Full height image 1.6:1
Use the chart below to choose which lens best suits your application.
if you need to be more precise, then use the calculations on the page immediately 
following the lens charts.
Notes
 This chart has a TRF of 1.1, for 
use with the following images:
1.6:1
feetmetres
Screen width
              10             20             30...

Page 2.10  Rev C August 2009
2. Installation  Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 This chart has a TRF of 1.33, 
for use with the following 
images:
4:3 = 1.33
Lens charts continued
Full height image 4:3
Use the chart below to choose which lens best suits your application.
if you need to be more precise, then use the calculations on the page immediately 
following the lens charts.
feetmetres
Screen width
              10             20             30...

Rev C August 2009 Page 2.11
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual   2. Installation

Notes
 The Throw ratio for a particular 
lens is fixed, and assumes that 
the image fills the width of the 
DMD.
  For images that do not fill the 
width of the DMD, the Throw 
ratio is effectively increased. To 
correct for this, a Throw Ratio 
Factor (TRF) is used. 
Choosing a lens by calculation
For any screen size not listed above, or if you need to be more precise, then use...

Page 2.12  Rev C August 2009
2. Installation  Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 The Throw ratio for a particular 
lens is fixed, but assumes that 
the image fills the width of the 
DMD.
  For images that do not fill the 
width of the DMD, the Throw 
ratio is effectively increased. To 
correct for this, a Throw Ratio 
Factor (TRF) is used.
Useful lens calculations
The following lens calculations may be useful:
Throw ratio   =  Throw distance 
   Screen...

Rev C August 2009 Page 2.13
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual   2. Installation

Notes
 Each time a new lens is 
fitted	to	the	projector,	
the calibration procedure 
must be carried out. See 
Setup menu, in Section 4. 
Controlling the projector.
  Make sure the rear lens cap is 
removed, before fitting the lens.
 Make sure the front lens cap is 
removed, before switching on 
the projector.
 Be careful not to scratch 
the lens surfaces. If you do 
accidentally...

Page 2.14  Rev C August 2009
2. Installation  Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 For more information on using 
the Lens shift feature, see 
section 4. Using the menus, 
Using the control keys.
 If the lens is to be shifted in 
two directions combined, the 
maximum range is somewhat 
less, as can be seen below. 
(zoom lens shift shown).
full horizontal or vertical shift 
without distortion
combined shift 
is reduced
Shifting the image
The normal...

Rev C August 2009 Page 2.15
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual   2. Installation

Mounting the projector
The projector is designed to be used on a flat surface, but the optional rigging frame 
will allow it to be suspended from a lighting truss or rigging.  The four adjustable feet 
under the chassis allow the projector to be lowered onto a flat surface without any 
danger of hands being trapped between the bottom frame and the surface.
Chassis adjustment
If...

Page 2.16  Rev C August 2009
2. Installation  Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Adjusting the rigging frame
Coarse adjustment of projector level should be made by adjusting the length of 
the supporting wires or chains, or by adjusting the position of the truss or rigging. 
Once the initial coarse adjustment has been made, fine adjustment can be made by 
turning the frame adjusters on the rigging frame:
To tilt the projector forwards and backwards (pitch...

Rev C August 2009 Page 2.17
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual   2. Installation

Notes
 When stacking projectors, 
the stack MUST be vertical, 
to ensure that the stresses 
are distributed to all frame 
couplings.
 Make sure that the surface, 
ceiling or rigging that is 
to support the projector is 
capable of supporting the 
combined weight of all the 
projectors and lenses (see 
specification for weights).
 Do not place heavy objects 
on top of the projector...

Page 2.18  Rev C August 2009
2. Installation  Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 For more information on 
selecting an input source, see 
section 4. Overview, Using 
the control keys, and Using 
the menus.
  SDI not present on earlier 
models
  For more information about pin 
connections and control codes 
see section 7. Appendix.
  For more information on 
input modes see section 
4. Overview.
Connecting the projector
Signal Inputs
The following inputs...