Digital Projection Titan 1080p-600, Reference 1080p, Titan 1080p-700, 1080p Ultra Contrast User Manual

Rev C August 2009 Page 4.15
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When the OSD is OFF, all menu 
navigation keys will be disabled.
  When the OSD is switched back 
ON, the menus will remain OFF 
until the   key is pressed 
again. The menus will then 
reopen at the same point they 
were last viewed.
 If a menu is opened, and...

Page 4.16  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Press  to open the menu. The blue highlight moves to the first item in the 
menu, which may be submenu, for example the Projector Setup submenu.
To select a submenu, press  and  , for example the Lamp submenu. 
Press  to open the submenu. The submenu opens, with the title at the top.
To close the submenu and return to the previous level, press .
There may be up to...

Rev C August 2009 Page 4.17
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Slider bar
The highlighted slider bar shows which 
control is active currently.
To adjust the slider press  and .
Parameter selection
To select from a number of parameters, 
(shown one at a time to the right), 
press  and .
These two items are greyed out and 
the values are blank, showing that they 
are not available, due to the effect of 
settings made in other menus,...

Page 4.18  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Input menu
 To return to the main menu, press  up to three times.
 From the main menu:
Press  and   until Input is highlighted.
Press  to open the Input menu. The blue highlight moves to the first item in 
the menu. The  symbol shows which input is currently selected.
Input Source
Press  and   to select from:
1. RGB1
2. RGB2
3. DVI
4. SDI
5. Composite Video
6. S-Video...

Rev C August 2009 Page 4.19
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 For more information about 
input modes and input presets, 
see earlier in this section, Input 
modes and settings.
 
Input Menu 
  Presets
 
Input Menu 
  Presets
 
    Recall Presets A ~ H
Presets
Sixteen sets of parameters can be saved and recalled (A – S)....

Page 4.20  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 
Input Menu 
  Presets
 
    Save Presets A ~ H
Save presets
Press  and   to select Save Preset.
  Press 
 to open the Save Presets A ~ H submenu.
To save the current set of parameters, press  and   to select one of the 
Presets.
 For Presets J to S, select...

Rev C August 2009 Page 4.21
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Notes
 
Input Menu 
  Presets
 
    Delete Presets A ~ H
Delete presets
Press  and   to select Delete Preset.
  Press 
 to open the Delete Presets A ~ H submenu.
To delete a saved set of parameters, press  and   to select one of the 
Presets.
 For Presets J to S, select Delete Preset J ~ S then press 
 to open the 
J~S submenu. Press 
 and   to select the Preset....

Page 4.22  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 Some  menu controls can be 
accessed directly using the 
control keys (see earlier in this 
section).
 When using the menus, press 
OSD  or  to hide or 
reveal the On-Screen-Display.
 
Picture Menu
 Some menu items may be 
greyed out - unavailable due to 
the effect of settings made in 
other menus, or due to the type 
of input signal.
 The Saturation slider is...

Rev C August 2009 Page 4.23
Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual  4. Controlling the projector

Notes
 For more information about 
User gamma settings, see 
section 5. DP Userware.
 Parametric Gamma adjustment 
is available only when 
Parametric is selected in 
Gamma selection, above.
 Phase adjustment can be 
found in both the Picture and 
Geometry menus, and is 
available for RGB1 and RGB2 
inputs only.
Gamma Correction
Video recordings are often supplied with...

Page 4.24  Rev C August 2009
4. Controlling the projector Digital Projection TITAN 1080p-600/700, Reference, Ultra Contrast User Manual

Notes
 Aspect Ratio selection can be 
found in both the Picture and 
Geometry menus.
 When User Aspect is selected, 
the Aspect Ratio settings are 
taken from the User H Aspect 
and V Aspect settings made in 
the Geometry menu.
 The Sharpness slider is 
available for Composite, 
S-Video and Component SD 
inputs only.
Aspect Ratio
Press  and   to select Aspect Ratio....