Home > Dell > Printer > Dell 2130cn User Guide

Dell 2130cn User Guide

    Download as PDF Print this page Share this page

    Have a look at the manual Dell 2130cn User Guide online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 327 Dell manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							To block data received from certain IP addresses through the wired or wireless network. You can set up to five IP addresses. Any changes made become 
    effective after the printer is turned off and then on.  
    Values:  
       
    IEEE 802.1x  
    Purpose:  
    To disable the IEEE 802.1x authentication. Any changes made become effective after the printer is turned off and then on.  
       
    Reset LAN  
    Purpose:  
    To initialize wired network data stored in NV (non - volatile) memory. After executing this function and rebooting the printer, all wired network settings are reset 
    to their default values.  
       
    USB Settings  
    Use the  USB Settings  menu to change printer settings affecting a USB port.  
       
    Port Status  
    Purpose:  
    To enable or disable the USB interface. Any changes made become effective after the printer is turned off and then on.  
    Values:  
       
    System Settings  
    Use the  System Settings  menu to configure a variety of printer features.  
       
    PowerSaver Time  
    Purpose:  
    To specify the time for transition to power saver mode.  
    Values:  
    Enter 3 to put the printer in power saver mode three minutes after it finishes a job. This uses much less energy, but requires more warm - up time for the No. n/Address (n is 1 - 5.)* 1  
    Sets the IP address for Filter  n .  
    No. n/Mask (n is 1 - 5.)* 1  
    Sets the address mask for Filter  n .  
    No. n/Mode (n is 1 - 5.)* 1   Off*   Disable the IP Filter feature for Filter  n .  
    Accept   Accepts an access from the specified IP address.  
    Reject   Rejects an access from the specified IP address.  
    * 1
     This item is only available for LPD or Port9100.  
      NOTE:  This item is only displayed when the IEEE 802.1x authentication is enabled and the optional network protocol adapter is installed, and also when 
    the optional wireless printer adapter is not installed.
      NOTE:  Values marked by an asterisk (*) are the factory default menu settings.
    Enable*   The USB interface is enabled.  
    Disable   The USB interface is disabled.  
      NOTE:  Values marked by an asterisk (*) are the factory default menu settings.
    Mode1  
        3min.*  
    Specifies the amount of time before the printer enters the power saver mode 1 after it finishes a job.  
    1 - 30min.  
    Mode2   10min.*  
    Specifies the amount of time before the printer enters the power saver mode 2 after it goes into the power saver mode 1.  
    5 - 60min.    
    						
    							printer. Enter 3 if your printer shares an electrical circuit with room lighting and you notice lights flickering.  
    Select a high value if your printer is in constant use. Under most circumstances, this keeps the printer ready to operate with minimum warm - up time. Select a 
    value between 1 and 30 minutes for power save mode if you want a balance between energy consumption and a shorter warm - up period.  
    The printer automatically returns to the standby mode from the power saver mode when it receives data from the computer. You can also return the printer to 
    the standby mode by pressing any button on the operator panel.  
       
    Audio Tones  
    Purpose:  
    To configure settings for tones emitted by the printer during operation or when a warning message appears.   
    Values:  
       
    Fault Time - Out  
    Purpose:  
    Specifies in seconds the amount of time the printer should cancel for a job stops abnormally. The print job is cancelled if the time - out time is exceeded.  
    Values:  
       
    Time - Out  
    Purpose:  
    To specify in seconds the amount of time the printer should wait for data to arrive from the computer. The print job is cancelled if the time - out time is 
    exceeded.   
    Values:  
       
    Panel Language  
    Purpose:  
    To determine the language of the text on the operator panel screen.  Control Panel   Off*   Does not emit a tone when the operator panel input is correct.  
    On   Emits a tone when the operator panel input is correct.  
    Invalid Key   Off*   Does not emit a tone when the operator panel input is incorrect.  
    On   Emits a tone when the operator panel input is incorrect.  
    Machine Ready   Off*   Does not emit a tone when the printer becomes ready.  
    On   Emits a tone when the printer becomes ready.  
    Job Completed   Off*   Does not emit a tone when a job is complete.  
    On   Emits a tone when a job is complete.  
    Fault Tone   Off*   Does not emit a tone when a job ends abnormally.  
    On   Emits a tone when a job ends abnormally.  
    Alert Tone   Off*   Does not emit a tone when a problem occurs.  
    On   Emits a tone when a problem occurs.  
    Out of Paper   Off*   Does not emit a tone when the printer runs out of paper.  
    On   Emits a tone when the printer runs out of paper.  
    Low Toner Alert   Off*   Does not emit a tone when toner or some other consumable is low.  
    On   Emits a tone when toner or some other consumable is low.  
    Base Tone   Off*   Does not emit a tone when the operator panel display is returned to the default settings by scrolling the loop menu.  
    On   Emits a tone when the operator panel display is returned to the default settings by scrolling the loop menu.  
    60 sec.*  
    Specifies in seconds the amount of time the printer cancels for a job stops abnormally.  
    3 - 300 sec.  
    Off   Disables the fault timeout.  
    30 sec.*  
    Specifies  the amount of time the printer should wait for data to arrive from the computer.  
    5 - 300 sec.  
    Off   Disables the job timeout.    
    						
    							Values:  
       
    Auto Log Print  
    Purpose:  
    To automatically print a log of completed jobs after every 20 jobs.  
    Values:  
    Print logs can also be printed using the  Report/List   menu.  
       
    Print ID  
    Purpose:  
    To specify a location where the user ID is printed.   
    Values:  
       
    Print Text  
    Purpose:  
    To specify whether the printer outputs PDL data, which is not supported by the printer, as text when the printer receives it. Text data is printed on A4 or 
    Letter size paper.  
    Values:  
       
    Banner Sheet  
    Purpose:  
    To specify the position of banner sheet, and also specify the tray in which the banner sheet is loaded.  English*    
    Italiano   Deutsch  
      Dansk  
    Nederlands   Norsk  
    Svenska      
    Off*   Does not  automatically output a log of completed jobs .  
    On   Automatically outputs a log of completed jobs .  
      NOTE:  Restart your printer when you change the settings for the  RAM Disk  menu.
    Off*   Does not print the user ID.  
    Top Left   Prints the user ID on the top left of the page.  
    Top Right   Prints the user ID on the top right of the page.  
    Bottom Left   Prints the user ID on the bottom left of the page.  
    Bottom Right   Prints the user ID on the bottom right of the page.  
      NOTE:  When printing on DL size paper, a part of the user ID may not be printed correctly.
    On*   Prints the received data as text data.  
    Off   Does not print the received data.  
      NOTE:  You can prevent to mingle the documents together by inserting the banner sheet into every document.  
    						
    							   
    Values:  
       
    RAM Disk  
    Purpose:  
    To allocate memory to the RAM disk file system for the Secure Print and Proof Print features. Any changes made become effective after the printer is turned off 
    and then on.  
    Values:  
       
    Odd Page 2Sided  
    Purpose:  
    Specifies how the odd last page is printed when using duplex printing.  
    Values:  
       
    Substitute Tray  
    Purpose:  
    Specifies whether or not to use another size paper when the paper that is loaded in the specified tray does not match the paper size settings for the current 
    job.  
    Values:  
       
    mm/inch  Insert Position   Off*   Does not print the banner sheet.  
    Front   Prints on the beginning of document.  
    Back   Prints on the end of document.  
    Front & Back   Prints on both beginning and end of document.  
    Specify Tray * 1   Tray 1*   The banner sheet is loaded in standard 250 - sheet tray.  
    Tray 2   The banner sheet is loaded in optional 250 - sheet feeder.  
    * 1
     Only displayed when an optional 250 - sheet feeder is installed on the printer.  
    Disable*   Does not allocate memory to the RAM disk file system. Secure Print and Proof Print jobs will abort and be recorded to the job log.  
    50 - 500MB * 1  
    Specifies the amount of memory to allocate to the RAM disk file system. (50 MB step)  
    50 - 1000MB * 2  
    * 1
     Only displayed when the optional 512 MB memory is installed.  
    * 2
     Only displayed when the optional 1024 MB memory is installed.  
      NOTE:  The  RAM Disk  menu is displayed only when 512 MB or more memory is installed on the printer.
      NOTE:  Restart your printer when you change the settings for the  RAM Disk  menu.
    1 Sided*   Prints the odd last page upside down to the paper.  
    2 Sided   Prints the odd last page in normal direction to the paper.  
    Off   No tray size substitute accepted.  
    Larger Size   Substitutes paper of next largest size. When there is no larger paper size, the printer substitutes paper of nearest size.  
    Nearest Size*   Substitutes paper of nearest size.    
    						
    							Purpose:  
    Specifies the default measurement unit displayed after the numeric value on the operator panel.  
    Values:  
       
    Maintenance  
    Use the  Maintenance  menu to initialize the NV (non - volatile) memory, configure the plain paper quality adjustment settings, and configure the security settings.  
       
    F/W Version  
    Purpose:  
    To display the printers firmware version.  
       
    Service Tag  
    Purpose:  
    To display the printers service tag.  
       
    Paper Density  
    Purpose:  
    To specify paper density settings.  
    Values:  
       
    Adjust BTR  
    Purpose:  
    To specify the transfer roller voltage adjustment for each paper type.  
    Values:  millimeter (mm)   Selects millimeter as the default measurement unit.  
    inch ()   Selects inch as the default measurement unit.  
      NOTE:  The default for  mm/inch  varies depending on the default  Paper Size . The default  Paper Size  varies depending on country - specific factory default. 
    The default for  mm/inch  setting is  mm  when the default  Paper Size  is  A4 . The default for  mm/inch  setting is inch when the default  Paper Size  is  Letter .
      NOTE:  Values marked by an asterisk (*) are the factory default menu settings.
    Plain   Normal*  
    Light  
    Label   Normal*  
    Light  
      NOTICE:  The print quality changes depending on the setting values you select for this item.
    Plain   0*  
    - 6  -  +6  
    Plain Thick   0*  
    - 6  -  +6  
    Transparency   0*  
    - 6  -  +6  
    Covers   0*  
    - 6  -  +6  
    Covers Thick   0*  
    - 6  -  +6    
    						
    							   
    Adjust Fuser  
    Purpose:  
    To adjusts the fuser temperature setting for each paper type.  
    Values:  
       
    Auto Reg Adj  
    Purpose:   
    To specify whether to automatically perform color registration adjustment.  
    Values:  
       
    Color Reg Adj  
    Purpose:  
    To specify whether to manually perform color registration adjustment.  
    Manual Color Registration Adjustments are required such as after the printer is moved.   Label   0*  
    - 6  -  +6  
    Coated   0*  
    - 6  -  +6  
    Coated Thick   0*  
    - 6  -  +6  
    Envelope   0*  
    - 6  -  +6  
    Recycled   0*  
    - 6  -  +6  
      NOTICE:  The print quality changes depending on the setting values you select for this item.
    Plain   0*  
    - 6  -  +6  
    Plain Thick   0*  
    - 6  -  +6  
    Transparency   0*  
    - 6  -  +6  
    Covers   0*  
    - 6  -  +6  
    Covers Thick   0*  
    - 6  -  +6  
    Label   0*  
    - 6  -  +6  
    Coated   0*  
    - 6  -  +6  
    Coated Thick   0*  
    - 6  -  +6  
    Envelope   0*  
    - 6  -  +6  
    Recycled   0*  
    - 6  -  +6  
    On*   Automatically performs color registration adjustment .  
    Off   Does not  automatically perform color registration adjustment .  
      NOTE:  The  Color Reg Adj  feature can be configured when  Auto Reg Adj  is set to  Off .  
    						
    							Values:  
       
    Adjust Altitude  
    Purpose:  
    To specify the altitude of the location where the printer is installed.   
    The discharge phenomenon for charging the photo conductor varies with barometric pressure. Adjustments are performed by specifying the altitude of the 
    location where the printer is being used.   
    Values:  
       
    Clean Developer  
    Purpose:  
    To set whether to stir toner in a new toner cartridge.  
       
    Toner Refresh  
    Purpose:  
    To clean the toner in each toner cartridge.  
       
    Drum Refresh  
    Purpose:  
    To clean the surface of the PHD unit.  
       
    Init PrintMeter  
    Purpose:  
    To initialize the print meter of the printer. When the print meter is initialized, the meter count is reset to 0.  
       
    Reset Defaults  
    Purpose:  
    To initialize the NV (non - volatile) memory. After executing this function and rebooting the printer, all the menu parameters, except the parameters for the 
    network, are reset to their default values.  
        Auto 
    Correct   Automatically performs color registration correction.   
    ColorRegi 
    Chart   Prints a color registration chart. The color registration chart prints a lattice pattern of yellow, magenta, and cyan lines. On the chart, find the 
    values on the right side that are next to the straightest lines for each of the three colors. If the value for the straightest line is 0, color 
    registration adjustment is not required. If the value for the straightest line is any value other than 0, specify the adjustment values under 
    Enter Number .  
    Enter 
    Number   Fast Scan   Y   - 9 - +9   Specifies the values that are found in the color registration chart for Yellow.  
    M   - 9 - +9   Specifies the values that are found in the color registration chart for Magenta.  
    C   - 9 - +9   Specifies the values that are found in the color registration chart for Cyan.  
    Slow Scan   Y   - 9 - +9   Specifies the values that are found in the color registration chart for Yellow.  
    M   - 9 - +9   Specifies the values that are found in the color registration chart for Magenta.  
    C   - 9 - +9   Specifies the values that are found in the color registration chart for Cyan.  
      NOTICE:  An incorrect altitude adjustment setting leads to poor printing quality, incorrect indication of remaining toner, etc. 
    0m*  
    Specifies the altitude of the location where the printer is installed.  1000m  
    2000m  
    3000m    
    						
    							Clear Storage  
    Purpose:  
    To clear all files that are stored as Secure, Store, and Proof Print in the optional memory.  
       
    Non - Dell Toner  
    Purpose:  
    To specify whether or not to use another manufacturers toner cartridge.  
    Values:  
       
    PCL  
    Use the  PCL  menu to change printer settings that only affect jobs using the PCL emulation printer language.  
       
    Paper Tray  
    Purpose:  
    To specify the input tray.  
    Values:  
       
    Paper Size  
    Purpose:  
    To specify the default paper size.  
    Values:  
       
    Orientation    NOTE:  The  Clear Storage  menu is only displayed when an optional 256 MB or more memory is installed on your printer and  RAM Disk  under  System 
    Settings  is enabled.
      NOTICE:  Use of a non - Dell toner cartridge may result in some of the printers functions to be unavailable, a reduction in print quality, or deterioration of 
    printers reliability. Use of a new Dell brand toner cartridge is recommended for your printer. The Dell warranty does not cover any problems caused by 
    the use of any accessory, part, or component that is not supplied by Dell.
      NOTE:  Before you install another manufactures toner cartridge, be sure to restart the printer.
    Off*   Does not use another manufacturers toner cartridge.  
    On   Uses another manufacturers toner cartridge.  
      NOTE:  Values marked by an asterisk (*) are the factory default menu settings.
    Auto*   Automatically selects a tray according to the paper size and type settings of the printing job.  
    Tray 1   The paper is fed from the standard 250 - sheet tray.  
    Tray 2 * 1  
    The paper is fed from the optional 250 - sheet feeder.  
    SSF   The paper is fed from the single sheet feeder.  
    * 1
     Only displayed when an optional 250 - sheet feeder is installed on the printer.  
    A4 * 1  
    A5  
    B5  
    Letter * 1  
    8.5x13   Legal  
    Executive   Monarch  
    DL   C5  
    Envelope #10   Custom Size  
    * 1
     Denotes country - specific factory default values.  
      NOTE:  Selecting a custom size for the paper size prompts you to enter a custom length and width.  
    						
    							Purpose:  
    To specify how text and graphics are oriented on the page.  
    Values:  
       
    2 Sided  
    Purpose:  
    To set duplexing as the default for all print jobs. (Select  Duplex  from the printer driver to duplex only specific jobs.)  
    Values:  
       
    Font  
    Purpose:  
    To specify the default font from the fonts registered in the printer.  
    Values:  
        Portrait*   Prints text and graphics parallel to the short edge of the paper.  
    Landscape   Prints text and graphics parallel to the long edge of the paper.  
      NOTE:  The  2 Sided  menu is only available when the optional duplexer is installed on the printer.
    2 Sided Print   Off*   Prints on one side of the paper.  
    On   Prints on both sides of the paper.  
    Binding Edge   Flip long 
    edge*   Assumes binding along the long edge of the page. (Left edge for portrait orientation and top edge for landscape 
    orientation)  
    Flip short edge   Assumes binding along the short edge of the page. (Top edge for portrait orientation and left edge for landscape 
    orientation)  
      NOTE:  For details on the  Flip long edge  and  Flip short edge  options, see  Flip on Long Edge  and  Flip on Short Edge .
    CG Times   CG Times It   CG Times Bd  
    CG Times BdIt   Univers Md   Univers MdIt  
    Univers Bd   Univers BdIt   Univers MdCd  
    Univers MdCdIt   Univers BdCd   Univers BdCdIt  
    AntiqueOlv   AntiqueOlv It   AntiqueOlv Bd  
    CG Omega   CG Omega It   CG Omega Bd  
    CG Omega BdIt   GaramondAntiqua   Garamond Krsv  
    Garamond Hlb   GaramondKrsvHlb   Courier*  
    Courier It   Courier Bd   Courier BdIt  
    LetterGothic   LetterGothic It   LetterGothic Bd  
    Albertus Md   Albertus XBd   Clarendon Cd  
    Coronet   Marigold   Arial  
    Arial It   Arial Bd   Arial BdIt  
    Times New   Times New It   Times New Bd  
    Times New BdIt   Symbol   Wingdings  
    Line Printer   Times Roman   Times It  
    Times Bd   Times BdIt   Helvetica  
    Helvetica Ob   Helvetica Bd   Helvetica BdOb  
    CourierPS   CourierPS Ob   CourierPS Bd  
    CourierPS BdOb   SymbolPS   Palatino Roman  
    Palatino It   Palatino Bd   Palatino BdIt  
    ITCBookman Lt   ITCBookman LtIt   ITCBookmanDm  
    ITCBookmanDm It   HelveticaNr   HelveticaNr Ob  
    HelveticaNr Bd   HelveticaNrBdOb   N C Schbk Roman  
    N C Schbk It   N C Schbk Bd   N C Schbk BdIt  
    ITC A G Go Bk   ITC A G Go BkOb   ITC A G Go Dm  
    ITC A G Go DmOb   ZapfC MdIt   ZapfDingbats    
    						
    							Symbol Set  
    Purpose:  
    To specify a symbol set for a specified font.  
    Values:  
       
    Font Size  
    Purpose:  
    To specify the font size for scalable typographic fonts.  
    Values:  
    Font size refers to the height of the characters in the font. One point equals approximately 1/72 of an inch.  
    See also:  
    Pitch and Point Size  
       
    Font Pitch  
    Purpose:  
    To specify the font pitch for scalable monospaced fonts.  
    Values:  
    Font pitch refers to the number of fixed - space characters in a horizontal inch of type. For nonscalable monospaced fonts, the pitch is displayed, but cannot be 
    changed.  
    See also:  
    Pitch and Point Size  
       
    Form Line  
    Purpose:  
    To set the number of lines in a page.  
    Values:  ROMAN - 8*   ISO L1   ISO L2  
    ISO L5   ISO L6   PC - 8  
    PC - 8 DN   PC - 775   PC - 850  
    PC - 852   PC - 1004   PC - 8 TK  
    WIN L1   WIN L2   WIN L5  
    DESKTOP   PS TEXT   MC TEXT  
    MS PUB   MATH - 8   PS MATH  
    PI FONT   LEGAL   ISO - 4  
    ISO - 6   ISO - 11   ISO - 15  
    ISO - 17   ISO - 21   ISO - 60  
    ISO - 69   WIN 3.0   WINBALT  
    SYMBOL   WINGDINGS   DNGBTSMS  
    12.00*  
    Specify the values in increments of 0.25.  
    4.00  -  50.00  
      NOTE:  The  Font Size  menu is only displayed for typographic fonts.
    10.00*  
    Specify the value in increments of 0.01.  
    6.00 - 24.00  
      NOTE:  The  Font Pitch  menu is only displayed for fixed or monospaced fonts.
       
    						
    All Dell manuals Comments (0)

    Related Manuals for Dell 2130cn User Guide