Dell 2130cn User Guide

							System Settings   Invalid Key Tone   Displays whether to emit the tone when the operator panel input is incorrect.  Off  indicates that the tone is 
disabled.  
Machine Ready Tone   Displays whether to emit the tone when the printer becomes ready.  Off  indicates that the tone is disabled.  
Job Completed Tone   Displays whether to emit the tone when a print job is complete.  Off  indicates that the tone is disabled.  
Fault Tone   Displays whether to emit the tone when a job ends abnormally.  Off  indicates that the tone is disabled.  
Alert Tone   Displays whether to emit the tone when a problem occurs.  Off  indicates that the tone is disabled.  
Out of Paper Alert 
Tone   Displays whether to emit the tone when the printer runs out of paper.  Off  indicates that the tone is disabled.  
Low Toner Alert Tone   Displays whether to emit the tone when toner or some other consumable is low.  Off  indicates that the tone 
is disabled.  
Base Tone   Displays whether to emit the tone when the operator panel screen is returned to the default by scrolling the 
loop menu.  Off  indicates that the tone is disabled.  
Fault Time - Out   Displays the amount of time the printer cancels for a job stops abnormally.  
Time - Out   Displays the amount of time the printer waits for data to arrive from the computer.  
Panel Language   Displays the language used on the operator panel screen.  
Auto Log Print   Displays whether to automatically output a log of completed jobs.  
Print ID   Displays where to print a user ID on the output paper.  
Print Text   Displays whether the printer outputs PDL (Page Description Language) data, which is not supported by the 
printer, as text when the printer receives it.  
Banner Sheet Insert 
Position   Displays where to insert a banner sheet.  
Banner Sheet Specify 
Tray * 1
  Displays which input tray to use to insert a banner sheet.  
RAM Disk * 2  
Displays whether to allocate RAM for the file system for the Secure Print and Proof Print features.  
Odd Page 2 Sided* 3  
Displays how the odd last page is printed when using duplex printing.  
Substitute Tray   Displays whether to use another size paper when the paper that is loaded in the specified tray does not 
match the paper size settings for the current job.  
mm / inch   Displays the measurement unit used on the operator panel screen.  
USB Settings   Port Status   Displays whether the USB interface is enabled.  
PCL Settings   Paper Tray   Displays the paper tray setting.  
Paper Size   Displays the paper size setting.  
Custom Size  -  Y   Displays the length of custom size paper.  
Custom Size  -  X   Displays the width of custom size paper.  
Orientation   Displays how text and graphics are oriented on the page.  
2 Sided* 3  
Displays whether to do duplexing as the default for all print jobs.  
Font   Displays the selected font from the list of registered fonts.  
Symbol Set   Displays a symbol set for the specified font.  
Font Size   Displays the font size for scalable typographic fonts.  
Font Pitch   Displays the font pitch for scalable monospaced fonts.  
Form Line   Displays the number of characters in a line.  
Quantity   Displays the number of copies to print.  
Image Enhancement   Displays whether the Image Enhancement feature is enabled.  
Hex Dump   Displays whether the Hex Dump feature is enabled.  
Draft Mode   Displays whether to print in the draft mode.  
Line Termination   Displays whether to set the line termination.  
Default Color   Displays the color mode setting.  
Secure Settings   Panel Lock Set   Displays whether to lock  Admin Menu  with a password.  
Paper Density   Plain   Displays the paper density of plain paper.  
Label   Displays the paper density of labels.  
Adjust BTR   Plain   Displays the voltage setting of the transfer roller (from  - 6 to 6) for plain paper.  
Plain Thick   Displays the voltage setting of the transfer roller (from  - 6 to 6) for thick plain paper.  
Transparency   Displays the voltage setting of the transfer roller (from  - 6 to 6) for transparencies.  
Covers   Displays the voltage setting of the transfer roller (from  - 6 to 6) for cover paper.  
Covers Thick   Displays the voltage setting of the transfer roller (from  - 6 to 6) for thick cover paper.  
Label   Displays the voltage setting of the transfer roller (from  - 6 to 6) for labels.  
Coated   Displays the voltage setting of the transfer roller (from  - 6 to 6) for coated paper.  
Coated Thick   Displays the voltage setting of the transfer roller (from  - 6 to 6) for thick coated paper.  
Envelope   Displays the voltage setting of the transfer roller (from  - 6 to 6) for envelopes.  
Recycled   Displays the voltage setting of the transfer roller (from  - 6 to 6) for recycled paper.  
Plain   Displays the temperature setting of the fuser (from  - 6 to 6) for plain paper.  
Plain Thick   Displays the temperature setting of the fuser (from  - 6 to 6) for thick plain paper.  
Transparency   Displays the temperature setting of the fuser (from  - 6 to 6) for transparency.    
						

							   
Reports  
Purpose:  
To print various types of reports and lists.  
Values:  
   
Printer Settings   
The  Printer Settings  tab includes  System Settings ,  USB Settings ,  PCL Settings , and  Panel Settings  pages.  
   
System Settings  
Purpose:  
To configure the basic printer settings.  
Values:  Adjust Fuser   Covers   Displays the temperature setting of the fuser (from  - 6 to 6) for cover paper.  
Covers Thick   Displays the temperature setting of the fuser (from  - 6 to 6) for thick cover paper.  
Label   Displays the temperature setting of the fuser (from  - 6 to 6) for labels.  
Coated   Displays the temperature setting of the fuser (from  - 6 to 6) for coated paper.  
Coated Thick   Displays the temperature setting of the fuser (from  - 6 to 6) for thick coated paper.  
Envelope   Displays the temperature setting of the fuser (from  - 6 to 6) for envelopes.  
Recycled   Displays the temperature setting of the fuser (from  - 6 to 6) for recycled paper.  
Auto Registration Adjustment   Displays whether to automatically perform color registration adjustment.  
Adjust Altitude   Displays the altitude of the location where the printer is installed.  
Non - Dell Toner   Displays whether or not to use another manufacturers toner cartridge.  
Web Link 
Customization   Select Reorder URL   Displays a link used for ordering consumables, which can be accessed from  Order Supplies at:  in the Left 
Frame.  
Regular   Displays the regular URL ( http://accessories.us.dell.com/sna ) that can be linked to  Order Supplies at: .  
Premier   Displays the premier URL ( http://premier.dell.com ) that can be linked to  Order Supplies at: .  
Tray Settings   Tray 1 Paper Type   Displays the paper type setting of the standard 250 - sheet tray.  
Tray 1 Paper Size   Displays the paper size setting of the standard 250 - sheet tray.  
Tray 1 Custom Size  -  
Y   Displays the length of custom size paper loaded in the standard 250 - sheet tray.  
Tray 1 Custom Size  -  
X   Displays the width of custom size paper loaded in the standard 250 - sheet tray.  
Tray 2 Paper Type* 1  
Displays the paper type setting of the optional 250 - sheet feeder.  
Tray 2 Paper Size* 1  
Displays the paper size setting of the optional 250 - sheet feeder.  
Display Popup   Displays a popup menu that prompts to set the paper size and type when paper is loaded in the standard 
250 - sheet tray and optional 250 - sheet feeder.  
* 1
 This item is only available when the optional 250 - sheet feeder is installed.  
* 2
 This item is only available when the 512 MB, or higher, optional memory is installed.  
* 3
 This item is only available when the optional duplexer is installed.  
Printer Settings   Click the  Start  button to print the printer settings page.  
Panel Settings   Click the  Start  button to print the panel settings page.  
PCL Fonts List   Click the  Start  button to print the PCL (Hewlett - Packard Printer Control Language) Fonts List.  
PCL Macro List   Click the  Start  button to print the PCL Macro List.  
Job History   Click the  Start  button to print the Job History report.  
Error History   Click the  Start  button to print the Error History report.  
Print Meter   Click the  Start  button to print the Print Meter report.  
Color Test Page   Click the  Start  button to print the Color Test Page.  
Stored Documents   Click the  Start  button to print the Stored Documents list.  
This item is only available when the 512 MB, or higher, optional memory is installed and RAM Disk is set to on.  
Power Saver Timer 
Mode 1   Sets the time for transition to Power Saver Mode 1.    
						

							   
USB Settings  
Purpose:  
To change printer settings affecting a USB port.  
Values:  
   
PCL Settings  
Purpose:  
To change the printer settings that only affect jobs using the PCL emulation printer language.  
Values:  Power Saver Timer 
Mode 2   Sets the time for transition to Power Saver Mode 2.  
Control Panel Tone   Specifies whether to enable the tone that is emitted when the operator panel input is correct.  
Invalid Key Tone   Specifies whether to enable the tone that is emitted when the operator panel input is incorrect.  
Machine Ready Tone   Specifies whether to enable the tone that is emitted when the printer becomes ready.  
Job Completed Tone   Specifies whether to enable the tone that is emitted when a print job is complete.  
Fault Tone   Specifies whether to enable the tone that is emitted when a job ends abnormally.  
Alert Tone   Specifies whether to enable the tone that is emitted when a problem occurs.  
Out of Paper Alert Tone   Specifies whether to enable the tone that is emitted when the printer runs out of paper.  
Low Toner Alert Tone   Specifies whether to enable the tone that is emitted when toner or some other consumable is low.  
Base Tone   Specifies whether to enable the tone that is emitted when the operator panel screen returns to the default by scrolling the loop 
menu.  
Fault Time - Out   Specifies in seconds the amount of time the printer should cancel for a job stops abnormally. The print job is cancelled if the time -
out time is exceeded.  
Time - Out   Specifies in seconds the amount of time the printer should wait for data to arrive from the computer. The print job is cancelled if 
the time - out time is exceeded.  
Panel Language   Sets the language to be used on the operator panel.  
Auto Log Print   Specifies whether to automatically print a log of completed jobs after every 20 jobs.  
Print ID   Specifies where to print the user ID on the output paper.  
Print Text   Specifies whether the printer outputs PDL data, which is not supported by the printer, as text when the printer receives it.  
Banner Sheet Insert 
Position   Specifies where to insert a banner sheet.  
Banner Sheet Specify 
Tray* 1
  Specifies which input tray to use to insert a banner sheet.  
RAM Disk   Specifies whether to allocate RAM for the file system for the Secure Print and Proof Print features.  
This item is only available when the 512 MB, or higher, optional memory is installed.  
Odd Page 2 Sided* 2  
Specifies how the odd last page is printed when using duplex printing.  
Substitute Tray   Specifies whether or not to use another size paper when the paper that is loaded in the specified tray does not match the paper 
size settings for the current job.  
mm / inch   Specifies the measurement unit to be used on the operator panel screen as either mm or inches.  
* 1
 This item is only available when the optional 250 - sheet feeder is installed.  
* 2
 This item is only available when the optional duplexer is installed.  
Port Status   Specifies whether to enable the USB interface.  
Paper Tray   Specifies the input tray.  
Paper Size   Specifies the paper size.  
Custom Size  -  Y   Specifies the length of custom size paper.  
Custom Size  -  X   Specifies the width of custom size paper.  
Orientation   Specifies how text and graphics are oriented on the page.  
2 Sided   Sets duplexing as the default for all print jobs. This item is only available when the optional duplexer is installed.  
Font   Specifies the font from the list of registered fonts.  
Symbol Set   Specifies a symbol set for the specified font.  
Font Size   Specifies the font size for scalable typographic fonts.  
Font Pitch   Specifies the font pitch for scalable monospaced fonts.  
Form Line   Specifies the number of characters in a line.  
Quantity   Sets the number of copies to print.    
						

							   
Secure Settings  
Panel Lock  
Purpose:  
To set whether to lock  Admin Menu  with a password, and to set or change the password.  
Values:  
   
Printer Maintenance   
The  Printer Maintenance  tab includes  Paper Density ,  Adjust BTR ,  Adjust Fuser ,  Auto Registration Adjustment ,  Color Registration Adjustments ,  Clean 
Developer ,  Adjust Altitude ,  Reset Defaults ,  Storage ,  Non - Dell Toner ,  Initialize PrintMeter , and  Web Link Customization  pages.  
   
Paper Density  
Purpose:  
To specify the paper density.  
Values:  
   
Adjust BTR  
Purpose:  
To specify the reference voltage settings for the transfer roller.  
Values:  
   
Adjust Fuser  
Purpose:  
To specify the temperature settings value for the fuser.  Image 
Enhancement   Specifies whether to enable the Image Enhancement feature.  
Hex Dump   Specifies whether to help isolate the source of a print job problem. With Hex Dump selected, all data sent to the printer is printed in 
hexadecimal and character representation. Control codes are not executed.  
Draft Mode   Specifies whether to print in the draft mode.  
Line Termination   Specifies how to handle line terminations.  
Default Color   Specifies the print color mode to  Color  or  Black . This setting is used for print jobs without a specified color print mode.  
Panel Lock Set   Sets whether to lock  Admin Menu  with a password.  
New Password   Sets a password that is required to access  Admin Menu .  
Re - enter Password   Enter the new password again to confirm.  
  NOTE:  This menu sets a password to lock the operator panel. When changing the password for the  Dell Printer Configuration Web Tool , click  Set 
Password  on the Left Frame and set the password.
Plain   Sets the density of plain paper to  Light  or  Normal .  
Label   Sets the density of labels to  Light  or  Normal .  
Plain   Sets the reference voltage setting for the transfer roller for plain paper within the range of  - 6 to 6.  
Plain Thick   Sets the reference voltage setting for the transfer roller for thick plain paper within the range of  - 6 to 6.  
Transparency   Sets the reference voltage setting for the transfer roller for transparencies within the range of  - 6 to 6.  
Covers   Sets the reference voltage setting for the transfer roller for cover paper within the range of  - 6 to 6.  
Covers Thick   Sets the reference voltage setting for the transfer roller for thick cover paper within the range of  - 6 to 6.  
Label   Sets the reference voltage setting for the transfer roller for labels within the range of  - 6 to 6.  
Coated   Sets the reference voltage setting for the transfer roller for coated paper within the range of  - 6 to 6.  
Coated Thick   Sets the reference voltage setting for the transfer roller for thick coated paper within the range of  - 6 to 6.  
Envelope   Sets the reference voltage setting for the transfer roller for envelopes within the range of  - 6 to 6.  
Recycled   Sets the reference voltage setting for the transfer roller for recycled paper within the range of  - 6 to 6.    
						

							Values:  
   
Auto Registration Adjustment  
Purpose:  
To specify whether to automatically perform color registration adjustment.  
   
Color Registration Adjustments  
Purpose:  
To specify whether to manually perform color registration adjustment.  
Manual Color Registration Adjustments are required such as after the printer is moved.   
Values:  
   
Clean Developer  
Purpose:  
To clean each toner cartridge or PHD unit, or to stir toner in a new toner cartridge.  
Values:  
   
Adjust Altitude  
Purpose:  
To specify the altitude of the location where the printer is installed.   
The discharge phenomenon for charging the photo conductor varies with barometric pressure. Adjustments are performed by specifying the altitude of the 
location where the printer is being used.  
   
Reset Defaults  Plain   Sets the temperature settings for the fuser for plain paper within the range of  - 6 to 6.  
Plain Thick   Sets the temperature settings for the fuser for thick plain paper within the range of  - 6 to 6.  
Transparency   Sets the temperature settings for the fuser for transparencies within the range of  - 6 to 6.  
Covers   Sets the temperature settings for the fuser for cover paper within the range of  - 6 to 6.  
Covers Thick   Sets the temperature settings for the fuser for thick cover paper within the range of  - 6 to 6.  
Label   Sets the temperature settings for the fuser for labels within the range of  - 6 to 6.  
Coated   Sets the temperature settings for the fuser for coated paper within the range of  - 6 to 6.  
Coated Thick   Sets the temperature settings for the fuser for thick coated paper within the range of  - 6 to 6.  
Envelope   Sets the temperature settings for the fuser for envelopes within the range of  - 6 to 6.  
Recycled   Sets the temperature settings for the fuser for recycled paper within the range of  - 6 to 6.  
  NOTE:  The  Color Registration Adjustments  feature can be configured when  Auto Registration Adjustment  is set to  Off .
Auto 
Correct   Click  Start  to Automatically performs color registration correction.  
Color Regi 
Chart   Click  Start  to print a color registration chart. The color registration chart prints a lattice pattern of yellow, magenta, and cyan lines. On the chart, 
find the values on the right side that are next to the straightest lines for each of the three colors. If the value for the straightest line is 0, color 
registration adjustment is not required. If the value for the straightest line is any value other than 0, specify the adjustment values under  Color 
Registration Adjustments .  
Enter 
Number   Specifies fast scan (perpendicular to paper feed direction) and slow scan (paper feed direction) color adjustment values individually for Yellow, 
Magenta, and Cyan within the range of  - 9 to 9.  
Clean Developer   Stirs toner in a new toner cartridge.  
Yellow Toner Refresh   Cleans the toner in the yellow toner cartridge.  
Magenta Toner Refresh   Cleans the toner in the magenta toner cartridge.  
Cyan Toner Refresh   Cleans the toner in the cyan toner cartridge.  
Black Toner Refresh   Cleans the toner in the black toner cartridge.  
Drum Refresh   Cleans the surface of the PHD unit.     
						

							Purpose:  
To initialize the NV (nonvolatile) memory. After executing this function to automatically restart the printer and rebooting the printer, all the menu parameters 
are reset to their default values.  
Values:  
   
Storage  
Purpose:  
To clear all files stored in the RAM Disk.  
Values:  
   
Non - Dell Toner  
Purpose:  
To specify whether or not to use another manufacturers toner cartridge.  
   
Initialize PrintMeter  
Purpose:  
To initialize the print meter of the printer. When the print meter is initialized, the meter count is reset to 0.  
   
Web Link Customization  
Purpose:  
To specify a link used for ordering consumables, which can be accessed from  Order Supplies at:  in the Left Frame.  
Values:  
   
Print Server Settings  
Use the  Print Server Settings  menu to set the type of printer interface and necessary conditions for communications.  
The following tabbed pages are displayed in the top of the Right Frame.  
   
Print Server Reports   
The  Print Server Reports  tab includes  Print Server Setup Page ,  NetWare Setup Page , and  E - Mail Alert Setup Page .  
   
Print Server Setup Page  
Purpose:  
To verify the current settings of TCP/IP (Transmission Control Protocol/Internet Protocol) and printing ports. On this page, you can only verify the settings of  Reset Defaults and restart printer.   Click  Start  to initialize the non - volatile memory (NVM).  
Clear Storage   Click  Start  to clear all files that are stored as Secure and Proof Print in the RAM disk.  
This item is only available when the RAM disk is set to on.  
  NOTICE:  Use of a non - Dell toner cartridge may result in some of the printers functions to be unavailable, a reduction in print quality, or deterioration of 
printers reliability. Use of a new Dell brand toner cartridge is recommended for your printer. The Dell warranty does not cover any problems caused by 
the use of any accessory, part, or component that is not supplied by Dell.
  NOTE:  Before you use another manufactures toner cartridge, be sure to restart the printer.
Select Reorder URL   Select the regular or premier URL to be linked to  Order Supplies at: .  
Regular   Displays the regular URL ( http://accessories.us.dell.com/sna ) that can be linked to  Order Supplies at: .  
Premier   Displays the premier URL ( http://premier.dell.com ) that can be linked to  Order Supplies at: .    
						

							items. If you want to change the settings, go to the pages in the  Print Server Settings  tab.  
Values:  
Ethernet * 1   Ethernet Settings   Displays the current settings of Ethernet transmission rate and the duplex settings.  
Current Ethernet Settings   Displays the current Ethernet settings.  
MAC Address   Displays the printers MAC address.  
Wireless 
Settings * 2
  SSID   Displays the name that identifies the network.  
Network Type   Displays the network type from either the Ad - Hoc or Infrastructure mode.  
MAC Address   Displays the MAC address of the wireless printer adapter.  
Link Channel   Displays the channel number of the connection.  
Link Quality   Displays the quality of the connection.  
TCP/IP 
Settings   IP Mode   Displays the IP mode.  
Host Name   Displays the host name.  
IPv4   IP Address Mode   Displays the IP address mode.  
IP Address   Displays the IP address.  
Subnet Mask   Displays the subnet mask.  
Gateway Address   Displays the gateway address.  
IPv6   Use Manual Address   Displays whether to set the IP address manually.  
Manual Address   Displays the IP address.  
Stateless Address 1 - 3   Displays the stateless addresses.  
Link Local Address   Displays the link local address.  
Manual Gateway Address   Displays the gateway address.  
Auto Configure Gateway 
Address   Displays the gateway address.  
DNS   IPv4   Get DNS Server Address 
from DHCP   Displays whether to automatically get a DNS (Domain Name System) server 
address from the DHCP (Dynamic Host Configuration Protocol) server.  
Current DNS Server 
Address   Displays the DNS server address.  
IPv6   Get DNS Server Address 
from DHCPv6 - lite   Displays whether to automatically get a DNS server address from the DHCPv6 -
lite server.  
Current DNS Server 
Address   Displays the DNS server address.  
Priority to IPv6 DNS Name 
Resolution* 3
  Displays whether to use the DNS Name Resolution feature.  
LPD   Port Status   Displays the port status.  
Connection Time - Out   Displays the connection timeout period.  
Port9100   Port Status   Displays the port status.  
Port Number   Displays the port number.  
Connection Time - Out   Displays the connection timeout period.  
WSD * 4   Port Status   Displays the WSD port status.  
Port Number   Displays the WSD port number.  
Receive Time - Out   Displays the receive timeout period.  
Notification Time - Out   Displays the notification timeout period.  
Maximum Number of TTL   Displays the maximum number of TTLs.  
Maximum Number of 
Notification   Displays the maximum number of notifications.  
HTTP   Port Status   Displays the port status.  
Port Number   Displays the port number.  
Simultaneous Connections   Displays the number of connections received simultaneously by the client.  
Connection Time - Out   Displays the connection timeout period.  
SNMP   Port Status   Displays the port status.  
Enable SNMP v1/v2c 
Protocol* 4
  Displays the status of the  SNMP v1/v2c  feature.  
Enable SNMP v3 Protocol* 4  
Displays the status of the  SNMP v3  feature.  
SSL/TLS* 4   HTTPS   Displays the HTTPS status.  
Port Number   Displays the port number.  
IPsec 
Settings* 4
  Protocol   Displays the protocol status.  
IKE   Displays to use a pre shared key for IKE authentication.  
IKE SA Lifetime   Displays the lifetime for IKE SA.  
IPsec SA Lifetime   Displays the lifetime for IPsec SA.  
DH Group   Displays the DH group.  
PFS   Displays the PFS status.    
						

							   
NetWare Setup Page  
Purpose:  
To verify the current settings of Netware. In this page, you can only verify the settings of items. If you want to change the settings, go to the pages in the 
Print Server Settings  tab.  
Values:  
   
E - Mail Alert Setup Page  
Purpose:  
To verify the current settings of SMTP/POP (Simple Mail Transfer Protocol/Post Office Protocol) used for the e - mail feature and E - Mail Alerts feature. In this 
page, you can only verify the settings of items. If you want to change the settings, go to the pages in the  Print Server Settings  tab.  
Values:  
    Remote peers IPv4 address   Displays the IP address to connect to.  
Remote peers IPv6 address   Displays the IP address to connect to.  
Non IPsec communication 
policy   Displays the status of the  Non IPsec communication policy  feature.  
802.1x * 1 * 4   Enable IEEE 802.1x   Displays the status of IEEE 802.1x.  
Authentication Method   Displays the setting of authentication method for IEEE 802.1x.  
IP Filter 
(IPv4) * 5
  Access List   Displays the list of IP addresses that are permitted or denied access to the printer.  
* 1
 This settings are not displayed when the optional wireless printer adapter is installed.  
* 2
 An optional wireless printer adapter is required to display the item.  
* 3
 This item is only available when using Ipv6 dual mode.  
* 4
 An optional network protocol adapter is required to display the item.  
* 5
 This item is only available for LPD or Port9100.  
NetWare   Port Status   Displays the port status.  
Device Name   Displays the printer name.  
Active Mode   Displays the current mode for Active Mode.  
Tree Name   Displays the tree name.  
Context Name   Displays the context name of the Print Server Object.  
Polling Interval   Displays the time interval.  
Status Information   Displays messages according to the conditions of the printer.  
SLP   Active Discovery   Displays whether active discovery is enabled.  
  NOTE:  An optional network protocol adapter is required to display the  NetWare Setup Page .
E - Mail Server 
Settings   Port Status   Displays the port status.  
Primary SMTP Gateway   Displays the primary SMTP (Simple Mail Transfer Protocol) gateway.  
SMTP Port Number   Displays the SMTP port number.  
E - Mail Send 
Authentication   Displays the authentication method for outgoing e - mail.  
POP3 Server Address   Displays the POP3 (Post Office Protocol 3) server address.  
POP3 Port Number   Displays the POP3 port number.  
Reply Address   Displays the IP address of servers connected with SMTP protocol when data is incoming.  
SMTP Server Connection   Displays the status of the SMTP server connection.  
E - Mail Alert Settings   E - Mail List 1   Displays the acceptable e - mail addresses for the E - Mail Alert feature specified in  E - mail List 1 .  
Select Alerts for List 1   Supplies Alerts   Displays the status, and whether to receive an E - Mail Alert, for consumables.  
Paper Handling 
Alerts   Displays the status, and whether to receive an E - Mail Alert, for paper 
handling.  
Service Call   Displays the status, and whether to receive an E - Mail Alert, for Service Calls.  
E - Mail List 2   Displays the acceptable e - mail addresses for the E - Mail Alert feature specified in  E - mail List 2 .  
Select Alerts for List 2   Supplies Alerts   Displays the status, and whether to receive an E - Mail Alert, for consumables.  
Paper Handling 
Alerts   Displays the status, and whether to receive an E - Mail Alert, for paper 
handling.  
Service Call   Displays the status, and whether to receive an E - Mail Alert, for Service Calls.    
						

							   
Print Server Settings   
The  Print Server Settings  tab includes  Basic Information ,  Port Settings ,  Wireless LAN ,  TCP/IP ,  NetWare ,  E - Mail Alert , and  SNMP  pages.  
   
Basic Information  
Purpose:  
To configure the printers basic information.  
Values:  
   
Port Settings  
Purpose:  
To specify whether to enable or disable printing ports and management protocol features.  
Values:  
   
Wireless LAN  
Purpose:  
To configure the detailed setting for the wireless network.  
Values:  System 
Settings   Printer Name   Specifies the name of the printer using up to 31 alphanumeric characters.  
Location   Specifies the location of the printer using up to 63 alphanumeric characters.  
Contact Person   Specifies the contact name, number, and other information of the printers administrator and service center using 
up to 63 alphanumeric characters.  
Administrator E - Mail 
Address   Specifies the contact address of the printers administrator and service center using up to 63 alphanumeric 
characters.  
Asset Tag Number   Enter the asset tag number for the printer.  
EWS Settings   Auto Refresh   Sets whether or not to automatically refresh the contents of the status display pages.   
Auto Refresh Interval   Sets the time interval for refreshing the contents of the status display pages automatically from 15 to 600 
seconds.  
  NOTE:  The  Auto Refresh  feature is effective for the contents of the Top Frame,  Printer Status  page,  Job List  page, and  Completed Jobs  page.
Ethernet * 1   Ethernet 
Settings   Auto   Detects Ethernet transmission rate and the duplex settings automatically.  
10BASE - T   
Half - Duplex   Selects 10Base - T Half - Duplex as the default value.  
10BASE - T   
Full - Duplex   Selects 10Base - T Full - Duplex as the default value.  
100BASE - TX Half - Duplex   Selects 100Base - T Half - Duplex as the default value.  
100BASE - TX Full - Duplex   Selects 100Base - T Full - Duplex as the default value.  
Current Ethernet Settings   Displays the current settings of Ethernet.  
MAC Address   Displays the printers MAC address.  
Port 
Status   LPD   Select the check box to enable LPD.  
Port9100   Select the check box to enable Port9100.  
WSD* 2  
Select the check box to enable the WSD port.  
NetWare * 2   Select the check box to enable the NetWare port. You can also configure the transport protocol to be used. TCP/IP can be 
selected as the transport protocol.  
E - Mail Alert   Select the check box to enable the  E - Mail Alert  feature.  
SNMP   Select the check box to enable the SNMP (Simple Network Management Protocol).   
You can also configure the transport protocol to be used. UDP can be selected as the transport protocol.  
* 1
 The  Ethernet  settings are not displayed when the optional wireless printer adapter is installed.  
* 2
 An optional network protocol adapter is required to display the item.  
  NOTE:  The settings in the  Port Settings  page will be valid only when the printer is rebooted. When you change or configure the settings, click the  Apply 
new settings  button to apply new settings.
SSID   Specifies the name that identifies the wireless network. Up to 32 alphanumeric characters.  
Network Type   Specifies the network type from either  Ad - Hoc  or  Infrastructure .    
						

							   
TCP/IP  
Purpose:  
To configure the IP address, subnet mask, and gateway address of the printer.   
Values:  Wireless 
Settings   MAC Address   Displays the MAC address of the printers wireless network adapter.  
Link Channel   Displays the channel number of the printers wireless connection.  
Link Quality   Displays the quality of the printers wireless network connection.  
Security 
Settings   Encryption   Select the security method from the list.  
WEP Key Code   Select the WEP key code from either  Hex  or  Ascii .  
WEP Key 
(Password)   Specifies the WEP key set used through the wireless network only when  WEP 128bits  or  WEP 64bits  is selected 
for  Encryption .  
Re - enter WEP Key   Enter the WEP key again to confirm it.  
Transmit Key 
(Index)   Specifies the transmit key from the list.  
Pass Phrase 
(Password)   Specifies the pass phrase from 8 to 63 alphanumeric characters only when  WPA2 - PSK AES  or  WPA - PSK AES , 
WPA - PSK TKIP  is selected for  Encryption .  
Re - enter Pass 
Phrase   Enter the pass phrase again to confirm it.  
  NOTE:  An optional wireless printer adapter is required to display the  Wireless LAN  page.
TCP/IP 
Settings   IP Mode   Specifies the IP mode.  
Host Name   Specifies the host name.  
IPv4   IP Address Mode   Selects the IP address mode.  
Manual IP Address   Sets the IP address.  
Manual Subnet Mask   Sets the subnet mask.  
Manual Gateway Address   Sets the gateway address.  
IPv6   Use Manual Address   Select the check box to set the IP address manually.  
Manual Address   Sets the IP address. To specify an IPv6 address, enter the address and then 64 
after a slash (/). For details, consult your system administrator.  
Manual Gateway Address   Sets the gateway address.  
DNS   DNS Domain Name   Specifies the domain name of the domain name server. Up to 255 alphanumeric characters, periods, and hyphens 
can be used. If you need to specify more than one domain name, separate them using a comma or semicolon.  
IPv4   Get DNS Server Address 
from DHCP   Select the check box to get the DNS server address automatically from the DHCP 
server.  
Manual DNS Server 
Address   Sets the DNS server address.  
IPv6   Get DNS Server Address 
from DHCPv6 - lite   Select the check box to get the DNS server address automatically from the DHCPv6 -
lite server.  
Manual DNS Server 
Address   Sets the DNS server address.  
Priority to IPv6 DNS 
Name Resolution   Select the check box to enable the DNS Name Resolution feature.  
LPD   Connection Time - Out   Sets the connection timeout period from 1 to 1000 seconds.  
IP Filter (IPv4)   To set the IP Filter settings, click  IP Filter  (IPv4). The  IP Filter  (IPv4) page is displayed.  
Port9100   Port Number   Sets the port number from 9000 to 9999.  
Connection Time - Out   Sets the connection timeout period between 1 and 1000 seconds.  
IP Filter (IPv4)   To set the IP Filter settings, click  IP Filter  (IPv4). The  IP Filter  (IPv4) page is displayed.  
WSD* 1   Port Number   Sets the port number to 80 or from 8000 to 9999.  
Receive Time - Out   Sets the receive timeout period from 1 to 65535 seconds.  
Notification Time - Out   Sets the notification timeout period from 1 to 60 seconds.  
Maximum Number of 
TTL   Sets the maximum number of TTL from 1 to 10.  
Maximum Number of 
Notification   Sets the maximum number of notifications from 10 to 20.  
HTTP   Port Number    Sets the port number to 80 or from 8000 to 9999.  
Simultaneous 
Connections   Displays the maximum number of connections received simultaneously by the client.  
Connection Time - Out   Sets the connection timeout period from 1 to 255 seconds.  
IP Filter 
(IPv4) * 2
  Address   Sets the address in the address field. Enter a numeric value between 0 and 255 in each field of 
aaa.bbb.ccc.ddd. However, 127 and 224 to 254 cannot be used to aaa.  
Address Mask   Sets the Subnet Mask in the Mask field. Enter a numeric value between 0 and 255 in each field.   
Reject   Rejects printing from specified network address.