compaq lte 5000 User Manual
Have a look at the manual compaq lte 5000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 229
2. If the mass storage device is a diskette drive or CD-ROM drive, remove
the diskette or CD from the drive.
3. Push the MultiBay device release button [1] and remove the device
[2] from the bay (Figure 7-5).
Installing a Hard Drive
Only hard drives that are configured for use as a secondary drive can be
used in MultiBay II of the expansion base. Drives without secondary drive
capability can be used only in MultiBay I of the expansion base. These
drives are labeled appropriately. See Appendix C of this...](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-228.png "Page 229
2. If the mass storage device is a diskette drive or CD-ROM drive, remove
the diskette or CD from the drive.
3. Push the MultiBay device release button [1] and remove the device
[2] from the bay (Figure 7-5).
Installing a Hard Drive
Only hard drives that are configured for use as a secondary drive can be
used in MultiBay II of the expansion base. Drives without secondary drive
capability can be used only in MultiBay I of the expansion base. These
drives are labeled appropriately. See Appendix C of this...")
![Page 231
side of the MultiBay and push the drive into the bay until it is
seated.
7.3.5 PC Card
All PC cards should be removed from the expansion base before performing
any internal maintenance on the computer.
Removing a PC Card
To remove a PC Card, complete the following steps:
1. Push the PC Card release button [1]. The card [2] ejects out of the
card slot (Figure 7-7).
2. The PC Card door automatically closes after removing the card.
Installing a PC Card
To install a PC Card, complete the following steps:
1....](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-230.png "Page 231
side of the MultiBay and push the drive into the bay until it is
seated.
7.3.5 PC Card
All PC cards should be removed from the expansion base before performing
any internal maintenance on the computer.
Removing a PC Card
To remove a PC Card, complete the following steps:
1. Push the PC Card release button [1]. The card [2] ejects out of the
card slot (Figure 7-7).
2. The PC Card door automatically closes after removing the card.
Installing a PC Card
To install a PC Card, complete the following steps:
1....")
side of the MultiBay and push the drive into the bay until it is seated. 7.3.5 PC Card All PC cards should be removed from the expansion base before performing any internal maintenance on the computer. Removing a PC Card To remove a PC Card, complete the following steps: 1. Push the PC Card release button [1]. The card [2] ejects out of the card slot (Figure 7-7). 2. The PC Card door automatically closes after removing the card. Installing a PC Card To install a PC Card, complete the following steps: 1. Push open the PC Card door so you can see the tracks inside.
2. Place the PC Card in the tracks with the card connector to the inside and label up. 3. Slide the card in until it seats. The door remains open while the card device is connected. Chapter 7.4 Expansion Base Feet The feet for the expansion base are rectangular, adhesive-backed rubber pads. Install the feet by removing the protective covering from the adhesive back and placing the feet in their positions on the bottom of the expansion base (Figure 7-8). Chapter 7.5 Bottom Cover Assembly The bottom cover assembly is spared as a unit and consists of: o Bottom cover o ISA expansion cover o Feet
o Labels The feet are also spared separately. Feet installation is described in Section 7.4. The feet, labels, and ISA expansion cover are preinstalled. To remove the bottom cover assembly, complete the following steps: 1. Prepare the expansion base for disassembly as described in Section 7.3. 2. Place the expansion base face down on the work surface and remove the two screws that secure the ISA expansion cover to the bottom cover (Figure 7-9). 3. Remove the ISA expansion cover (Figure 7-10)
4. Remove the one screw in the center of the shield on the bottom cover, remove the shield by sliding it forward and lifting it off the retaining clips, and then remove the remaining ten screws that secure the bottom cover to the expansion base (Figure 7-11).
5. Lift the bottom cover off the expansion base (Figure 7-12).
6. To remove the ISA connector board, remove the two screws, and remove the board (Figure 7-13).
To install the bottom cover assembly, reverse the procedure presented above. Chapter 7.6 MPEG Connector The MPEG connector plugs into the main board and is accessed by removing the bottom cover assembly. Remove the bottom cover assembly as described in Section 7.5 and disconnect the MPEG connector from the main board as shown in Figure 7-14.
Reverse this procedure to install the MPEG connector. Chapter 7.7 Power Supply The power supply is mounted in the right rear corner of the expansion base when viewed with the base placed top side down on the work surface. It is replaced as an assembly with its fan. To remove the power supply, complete the following steps: 1. Prepare the expansion base for disassembly as described in Section 7.3. 2. Remove the bottom cover assembly as described in Section 7.5.1. 3. Disconnect the power supply from the main board (Figure 7-15). 4. Disconnect the power supply fan cable from the main board (Figure 7-15).
5. Note the routing of the ground wires attached to the rear power supply screws. Remove the three screws and lift the power supply out (Figure 7-16).
To install the power supply, reverse the procedure presented above. Be sure to reconnect the ground wire. Chapter 7.8 Main Board To remove the main board, complete the following steps: 1. Prepare the expansion base for disassembly as described in Section 7.3. 2. Remove the two shoulder screws from the computer connector as shown in Figure 7-17.