compaq lte 5000 User Manual
Have a look at the manual compaq lte 5000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 212
Reverse the above procedure to install the IrDA board.
Chapter 6.15 Speaker Assemblies
The bottom cover assembly must be removed before removing the speaker
assembly. The speaker assembly is installed as a unit with its cable
permanently attached.
To remove the speaker assembly, complete the following steps:
1. Prepare the expansion base for disassembly as described in Section 6.3.
2. Remove the bottom cover assembly as described in Section 6.5.
3. Note the cable routing [2] and disconnect the speaker...](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-211.png "Page 212
Reverse the above procedure to install the IrDA board.
Chapter 6.15 Speaker Assemblies
The bottom cover assembly must be removed before removing the speaker
assembly. The speaker assembly is installed as a unit with its cable
permanently attached.
To remove the speaker assembly, complete the following steps:
1. Prepare the expansion base for disassembly as described in Section 6.3.
2. Remove the bottom cover assembly as described in Section 6.5.
3. Note the cable routing [2] and disconnect the speaker...")
![Page 213
4. Remove the two screws from the speaker bracket [3] and lift the bracket
and board out of the bottom cover assembly [4] (Figure 6-28).
Reverse the above procedure to install a speaker assembly, paying
particular attention to the cable routing.
Chapter 6.16 Alignment Guides
The bottom cover assembly must be removed before removing the alignment
guides. The alignment guide assembly consists of the guide, spring, and
bracket.
IMPORTANT: There is a left alignment guide and a right alignment guide.
They...](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-212.png "Page 213
4. Remove the two screws from the speaker bracket [3] and lift the bracket
and board out of the bottom cover assembly [4] (Figure 6-28).
Reverse the above procedure to install a speaker assembly, paying
particular attention to the cable routing.
Chapter 6.16 Alignment Guides
The bottom cover assembly must be removed before removing the alignment
guides. The alignment guide assembly consists of the guide, spring, and
bracket.
IMPORTANT: There is a left alignment guide and a right alignment guide.
They...")
![Page 216
To remove the docking mechanism, complete the following steps:
1. Prepare the expansion base for disassembly as described in Section 6.3.
2. Remove the bottom cover assembly as described in Section 6.5.
3. Remove the main board as described in Section 6.8.
4. Remove the screw and washer [1] that connects the docking bar [2] to
the puller plate assembly [3] (Figure 6-31).
5. Lift the docking bar [1] and its bushing [2] out of the assembly
(Figure 6-32).](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-215.png "Page 216
To remove the docking mechanism, complete the following steps:
1. Prepare the expansion base for disassembly as described in Section 6.3.
2. Remove the bottom cover assembly as described in Section 6.5.
3. Remove the main board as described in Section 6.8.
4. Remove the screw and washer [1] that connects the docking bar [2] to
the puller plate assembly [3] (Figure 6-31).
5. Lift the docking bar [1] and its bushing [2] out of the assembly
(Figure 6-32).")
4. Remove the screw holding the IrDA board in place and lift the board out (Figure 6-27).
Reverse the above procedure to install the IrDA board. Chapter 6.15 Speaker Assemblies The bottom cover assembly must be removed before removing the speaker assembly. The speaker assembly is installed as a unit with its cable permanently attached. To remove the speaker assembly, complete the following steps: 1. Prepare the expansion base for disassembly as described in Section 6.3. 2. Remove the bottom cover assembly as described in Section 6.5. 3. Note the cable routing [2] and disconnect the speaker cable [1] from the main board (Figure 6-28).
4. Remove the two screws from the speaker bracket [3] and lift the bracket and board out of the bottom cover assembly [4] (Figure 6-28). Reverse the above procedure to install a speaker assembly, paying particular attention to the cable routing. Chapter 6.16 Alignment Guides The bottom cover assembly must be removed before removing the alignment guides. The alignment guide assembly consists of the guide, spring, and bracket. IMPORTANT: There is a left alignment guide and a right alignment guide. They are keyed for proper installation. The assembly is mounted to the expansion base with one screw. To remove the CPU guide assembly, complete the following steps: 1. Prepare the expansion base for disassembly as described in Section 6.3. 2. Remove the bottom cover assembly as described in Section 6.5.
3. Remove the guide screw (Figure 6-29). 4. Remove the CPU guide while guiding the spring out of its seat in the side panel of the expansion base (Figure 6-29). Reverse the above procedure to install the CPU guide. Install the spring in its seat first and make certain it is seated completely. Do not over tighten the screw; the guide must be free to slide under the screw head. Chapter 6.17 Monitor Support Cover Cap The bottom cover must be removed before removing the monitor support cover cap. The monitor support cover cap and spring snap into place. To remove the cap and spring, complete the following steps: 1. Prepare the expansion base for disassembly as described in Section 6.3. 2. Remove the bottom cover assembly as described in Section 6.5. 3. Squeeze the tabs and allow the cap to drop out (Figure 6-30).
Reverse the above procedure to install the monitor support cover cap. Chapter 6.18 Docking Mechanism The bottom cover assembly must be removed before removing the docking mechanism. The docking mechanism consists of the: o Docking lever o Docking lever cover o Docking lever shield o Slide block o Docking bar o Docking bar bushing o Puller plate assembly o Spring
To remove the docking mechanism, complete the following steps: 1. Prepare the expansion base for disassembly as described in Section 6.3. 2. Remove the bottom cover assembly as described in Section 6.5. 3. Remove the main board as described in Section 6.8. 4. Remove the screw and washer [1] that connects the docking bar [2] to the puller plate assembly [3] (Figure 6-31). 5. Lift the docking bar [1] and its bushing [2] out of the assembly (Figure 6-32).
6. Remove the screw from the spring and lift the spring out (Figure 6-33).
7. To remove the puller plate assembly [1], see Figure 6-34 and complete the following steps: a. Slide the puller plate all the way back [2].
b. Lift the rear of the puller plate [4] and continue to slide back while pulling the catch [3] out of the opening in the base. To install the puller plate assembly, press the docking aid [3] through the opening and slide the puller plate [1] into place (Figure 6-34). Reverse the previous procedure to install the docking mechanism. Be sure to use nylock screws for the docking bar and spring. Chapter 6.19 Docking Lever and Cover To remove the docking lever and cover, complete the following steps: 1. Prepare the expansion base for disassembly as described in Section 6.3. 2. Remove the bottom cover assembly as described in Section 6.5. 3. Remove the screw and washer that connects the docking bar to the slide block and docking lever (Figure 6-35).
4. The docking lever slider is now free to be removed [1] (Figure 6-36). Note that the little tab on one side of the docking lever slider [2] goes toward the outside of the expansion base at reassembly.