compaq lte 5000 User Manual
Have a look at the manual compaq lte 5000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 157
4. Lift out the latch [2] and its attached spring (Figure 5-33).
Reverse the above procedure to install a latch assembly.
5.8.4 Removing and Installing the Clutch Assembly
To remove a clutch assembly, complete the following steps:
1. Remove the display assembly as described in Section 5.8.1.
2. Remove the display bezel as described in Section 5.8.2.
3. Remove the screws holding the clutch assembly and bracket to the
display housing (Figure 5-34), and remove the clutch assembly and
bracket.](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-156.png "Page 157
4. Lift out the latch [2] and its attached spring (Figure 5-33).
Reverse the above procedure to install a latch assembly.
5.8.4 Removing and Installing the Clutch Assembly
To remove a clutch assembly, complete the following steps:
1. Remove the display assembly as described in Section 5.8.1.
2. Remove the display bezel as described in Section 5.8.2.
3. Remove the screws holding the clutch assembly and bracket to the
display housing (Figure 5-34), and remove the clutch assembly and
bracket.")
![Page 161
1. Remove the CPU cover as described in Section 5.5.1.
2. Remove the keyboard screws (Figure 5-37).
3. Remove the screws [1] from the rear corners of the keyboard
(Figure 5-38). Note that ground lugs are attached by these screws.](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-160.png "Page 161
1. Remove the CPU cover as described in Section 5.5.1.
2. Remove the keyboard screws (Figure 5-37).
3. Remove the screws [1] from the rear corners of the keyboard
(Figure 5-38). Note that ground lugs are attached by these screws.")
![Page 162
4. Remove the microphone [2] (Figure 5-38). You can leave it attached to
its extension cable.
5. Separate the keyboard from the base and shift it slightly to gain
better access to the keyboard ZIF connector [1] (Figure 5-39), then
disconnect the ZIF connector.](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-161.png "Page 162
4. Remove the microphone [2] (Figure 5-38). You can leave it attached to
its extension cable.
5. Separate the keyboard from the base and shift it slightly to gain
better access to the keyboard ZIF connector [1] (Figure 5-39), then
disconnect the ZIF connector.")
![Page 163
6. Disconnect the EasyPoint II controller cable [2] from the system board
(Figure 5-39).
7. Lift the keyboard out.
Reverse this procedure to install the keyboard.
NOTE: Be sure to connect the ground lugs at the rear of the keyboard.
5.9.2 Removing and Installing the EasyPoint II Controller
To remove the EasyPoint II controller, complete the following steps:
1. Remove the keyboard as described in Section 5.9.1.
2. Remove the two screws from the EasyPoint II controller
(Figure 5-40).](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-162.png "Page 163
6. Disconnect the EasyPoint II controller cable [2] from the system board
(Figure 5-39).
7. Lift the keyboard out.
Reverse this procedure to install the keyboard.
NOTE: Be sure to connect the ground lugs at the rear of the keyboard.
5.9.2 Removing and Installing the EasyPoint II Controller
To remove the EasyPoint II controller, complete the following steps:
1. Remove the keyboard as described in Section 5.9.1.
2. Remove the two screws from the EasyPoint II controller
(Figure 5-40).")
![Page 165
NOTE: Observe the dressing of the EasyPoint II controller cables. It may
be necessary to use adhesive tape to maintain the cables in their
proper orientations.
Reverse the above procedure to install the EasyPoint II controller.
5.9.3 Removing and Installing the Battery Release Assembly
To remove the battery release assembly, complete the following steps:
1. Remove the keyboard as described in Section 5.9.1.
2. Remove the two screws [1] from the release holder [3] (Figure 5-42).](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-164.png "Page 165
NOTE: Observe the dressing of the EasyPoint II controller cables. It may
be necessary to use adhesive tape to maintain the cables in their
proper orientations.
Reverse the above procedure to install the EasyPoint II controller.
5.9.3 Removing and Installing the Battery Release Assembly
To remove the battery release assembly, complete the following steps:
1. Remove the keyboard as described in Section 5.9.1.
2. Remove the two screws [1] from the release holder [3] (Figure 5-42).")
![Page 166
3. The release holder, spring, and latch are installed as an assembly.
Lift out the release holder [3] (Figure 5-42). The battery release [2]
is attached to the release holder with its spring [4].
Reverse the above procedure to install the battery release assembly. Use
the locating pins adjacent to each mounting hole to locate the release
holder properly.
NOTE: At reassembly, make certain that the spring on the battery release
is not trapped between the release holder and side plastic. The
spring should...](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-165.png "Page 166
3. The release holder, spring, and latch are installed as an assembly.
Lift out the release holder [3] (Figure 5-42). The battery release [2]
is attached to the release holder with its spring [4].
Reverse the above procedure to install the battery release assembly. Use
the locating pins adjacent to each mounting hole to locate the release
holder properly.
NOTE: At reassembly, make certain that the spring on the battery release
is not trapped between the release holder and side plastic. The
spring should...")
1. Remove the CPU cover as described in Section 5.5.1. 2. Remove the keyboard screws (Figure 5-37). 3. Remove the screws [1] from the rear corners of the keyboard (Figure 5-38). Note that ground lugs are attached by these screws.
4. Remove the microphone [2] (Figure 5-38). You can leave it attached to its extension cable. 5. Separate the keyboard from the base and shift it slightly to gain better access to the keyboard ZIF connector [1] (Figure 5-39), then disconnect the ZIF connector.
6. Disconnect the EasyPoint II controller cable [2] from the system board (Figure 5-39). 7. Lift the keyboard out. Reverse this procedure to install the keyboard. NOTE: Be sure to connect the ground lugs at the rear of the keyboard. 5.9.2 Removing and Installing the EasyPoint II Controller To remove the EasyPoint II controller, complete the following steps: 1. Remove the keyboard as described in Section 5.9.1. 2. Remove the two screws from the EasyPoint II controller (Figure 5-40).
3. Disconnect the cable from the ZIF connector on the EasyPoint II Controller (Figure 5-41). The ZIF connector is located on the back side of the controller board.
NOTE: Observe the dressing of the EasyPoint II controller cables. It may be necessary to use adhesive tape to maintain the cables in their proper orientations. Reverse the above procedure to install the EasyPoint II controller. 5.9.3 Removing and Installing the Battery Release Assembly To remove the battery release assembly, complete the following steps: 1. Remove the keyboard as described in Section 5.9.1. 2. Remove the two screws [1] from the release holder [3] (Figure 5-42).
3. The release holder, spring, and latch are installed as an assembly. Lift out the release holder [3] (Figure 5-42). The battery release [2] is attached to the release holder with its spring [4]. Reverse the above procedure to install the battery release assembly. Use the locating pins adjacent to each mounting hole to locate the release holder properly. NOTE: At reassembly, make certain that the spring on the battery release is not trapped between the release holder and side plastic. The spring should be below the holder (Figure 5-43).
5.9.4 Removing and Installing the MultiBay Release Assembly To remove the MultiBay release assembly, complete the following steps: 1. Remove the keyboard as described in Section 5.9.1. 2. Remove the standoff [1] from the CD-ROM eject bar [2] and lift out the eject bar (Figure 5-44).
3. Remove the standoff and screw from the release holder (Figure 5-45).
4. Lift out the release holder (Figure 5-45). The release is attached to the holder with its spring. The release holder, spring and latch are installed as an assembly. Reverse the above procedure to install the MultiBay release assembly. Use the locating pins adjacent to each mounting hole to locate the release holder properly. NOTE: At reassembly, make certain that the spring on the MultiBay release is not trapped between the release holder and side plastic. The spring should be below the holder. (Figure 5-46).
5.9.5 Removing and Installing the Hard Drive Latch The hard drive latch assembly consists of the hard drive release, latch, and spring. It is held in place with one screw. To remove and replace the hard drive latch, complete the following steps: 1. Remove the keyboard as described in Section 5.9.1. 2. Remove the hard drive security screw (Figure 5-47)