compaq lte 5000 User Manual
Have a look at the manual compaq lte 5000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 216
To remove the docking mechanism, complete the following steps:
1. Prepare the expansion base for disassembly as described in Section 6.3.
2. Remove the bottom cover assembly as described in Section 6.5.
3. Remove the main board as described in Section 6.8.
4. Remove the screw and washer [1] that connects the docking bar [2] to
the puller plate assembly [3] (Figure 6-31).
5. Lift the docking bar [1] and its bushing [2] out of the assembly
(Figure 6-32).](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-215.png "Page 216
To remove the docking mechanism, complete the following steps:
1. Prepare the expansion base for disassembly as described in Section 6.3.
2. Remove the bottom cover assembly as described in Section 6.5.
3. Remove the main board as described in Section 6.8.
4. Remove the screw and washer [1] that connects the docking bar [2] to
the puller plate assembly [3] (Figure 6-31).
5. Lift the docking bar [1] and its bushing [2] out of the assembly
(Figure 6-32).")
![Page 218
7. To remove the puller plate assembly [1], see Figure 6-34 and complete
the following steps:
a. Slide the puller plate all the way back [2].](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-217.png "Page 218
7. To remove the puller plate assembly [1], see Figure 6-34 and complete
the following steps:
a. Slide the puller plate all the way back [2].")
![Page 219
b. Lift the rear of the puller plate [4] and continue to slide back
while pulling the catch [3] out of the opening in the base.
To install the puller plate assembly, press the docking aid [3] through
the opening and slide the puller plate [1] into place (Figure 6-34).
Reverse the previous procedure to install the docking mechanism. Be sure
to use nylock screws for the docking bar and spring.
Chapter 6.19 Docking Lever and Cover
To remove the docking lever and cover, complete the following steps:
1....](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-218.png "Page 219
b. Lift the rear of the puller plate [4] and continue to slide back
while pulling the catch [3] out of the opening in the base.
To install the puller plate assembly, press the docking aid [3] through
the opening and slide the puller plate [1] into place (Figure 6-34).
Reverse the previous procedure to install the docking mechanism. Be sure
to use nylock screws for the docking bar and spring.
Chapter 6.19 Docking Lever and Cover
To remove the docking lever and cover, complete the following steps:
1....")
![Page 220
4. The docking lever slider is now free to be removed [1] (Figure 6-36).
Note that the little tab on one side of the docking lever slider [2]
goes toward the outside of the expansion base at reassembly.](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-219.png "Page 220
4. The docking lever slider is now free to be removed [1] (Figure 6-36).
Note that the little tab on one side of the docking lever slider [2]
goes toward the outside of the expansion base at reassembly.")
![Page 221
5. Remove the screws [1] and lift out the docking lever cover [2]
(Figure 6-37).](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-220.png "Page 221
5. Remove the screws [1] and lift out the docking lever cover [2]
(Figure 6-37).")
![Page 222
6. Remove the docking lever cover insert [3] as shown in Figure 6-37.
Reverse the above procedures to install the docking lever, docking lever
slider, or docking lever cover.
Chapter 6.20 Security Lock Bracket
The security lock bracket simply slides into its mounting seat on the side
of the expansion base. To remove and install the security lock bracket,
complete the following steps:
1. Prepare the expansion base for disassembly as described in Section 6.3.
2. Remove the bottom cover assembly as...](http://img.usermanuals.tech/thumb/1258/38934/w64_compaq-lte-5000-221.png "Page 222
6. Remove the docking lever cover insert [3] as shown in Figure 6-37.
Reverse the above procedures to install the docking lever, docking lever
slider, or docking lever cover.
Chapter 6.20 Security Lock Bracket
The security lock bracket simply slides into its mounting seat on the side
of the expansion base. To remove and install the security lock bracket,
complete the following steps:
1. Prepare the expansion base for disassembly as described in Section 6.3.
2. Remove the bottom cover assembly as...")
5. Remove the screws [1] and lift out the docking lever cover [2] (Figure 6-37).
6. Remove the docking lever cover insert [3] as shown in Figure 6-37. Reverse the above procedures to install the docking lever, docking lever slider, or docking lever cover. Chapter 6.20 Security Lock Bracket The security lock bracket simply slides into its mounting seat on the side of the expansion base. To remove and install the security lock bracket, complete the following steps: 1. Prepare the expansion base for disassembly as described in Section 6.3. 2. Remove the bottom cover assembly as described in Section 6.5. 3. Use a flat-blade screwdriver to pry the bracket straight up, or use a small pair of pliers to grasp the bracket and pull it out (Figure 6-38).
Chapter 7. MultiBay ISA Expansion Base: Removal and Replacement Procedures Chapter 7.0 Introduction This chapter presents the removal and replacement procedures for the MultiBay ISA Expansion Base. Chapter 7.1 Serial Number The expansion base serial number should be reported to Compaq when requesting information or ordering spare parts. The serial number is displayed on the rear of the expansion base to the right of the auxiliary fan. Chapter 7.2 Disassembly Sequence Chart Use the chart in Figure 7-2 to determine the section number and disassembly sequence for removing components from the MultiBay ISA Expansion Base.
Chapter 7.3 Preparing the MultiBay ISA Expansion Base For Disassembly NOTE: It is important that these instructions be followed when installing a new expansion base top cover (Service Spare Part Number 213711-003). 1. Remove the plastic hole cover from the left corner of the top cover. 2. Insert the fan (which is included with the new top cover) in the open space. 3. Plug the fan electrical connector to the I/O board, adjacent to the power supply. Before beginning removal and replacement procedures, complete the following steps: 1. Undock the computer from the expansion base (Section 5.3.1). 2. Disconnect AC power and any external devices (Section 7.3.1). 3. Remove the battery pack(s) (Section 7.3.2). 4. Remove the mass storage devices (Section 7.3.3).
5. Remove any PC Cards (section 7.3.4). 7.3.1 Undocking the Computer See Section 5.3.1 for instructions on how to undock the computer from the expansion base. 7.3.2 Disconnecting the Expansion Base 1. Turn off the expansion base and undock the computer if it is docked in the expansion base. See Section 5.3.1 for detailed instructions. 2. Disconnect the power cord from the AC source and from the expansion base. 3. Disconnect all peripheral devices from the expansion base. 4. Complete the preparation for disassembly by performing the procedures described in Sections 7.3.3 through 7.3.5. 7.3.3 Battery Pack
All battery packs should be removed from the expansion base before performing any internal maintenance. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> WARNING >>>>>>
2. Move the sliding panel on the front of the battery to the left. Installing a Battery Pack To install a battery pack into a MultiBay, complete the following steps: 1. With the label facing up and the connectors facing in, align the left side of the battery pack with the left side of the MultiBay, and push the battery pack into the MultiBay until it is seated. 2. Move the sliding panel on the front of the battery pack to the right to cover the MultiBay opening. 7.3.4 Mass Storage Devices Removing a Mass Storage Device To remove mass storage devices from the expansion base, complete the following steps: 1. Save and close any files that reside on the drive that is to be removed.
2. If the mass storage device is a diskette drive or CD-ROM drive, remove the diskette or CD from the drive. 3. Push the MultiBay device release button [1] and remove the device [2] from the bay (Figure 7-5). Installing a Hard Drive Only hard drives that are configured for use as a secondary drive can be used in MultiBay II of the expansion base. Drives without secondary drive capability can be used only in MultiBay I of the expansion base. These drives are labeled appropriately. See Appendix C of this manual for more details. >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>> CAUTION >>>>>
1. Turn off the expansion base. 2. Make sure the latch inside the carrier is pushed to the right, and place the hard drive in the carrier with the label facing up and the contacts facing the rear of the carrier. 3. Slide the drive toward the rear of the carrier until it is seated (Figure 7-6). 4. Push the latch inside the carrier to the left to secure the hard drive in place. 5. Align the left side of the carrier with the left side of the MultiBay, and push the carrier into the bay until it is seated. Installing a Diskette Drive or CD-ROM Drive To install a diskette drive or CD-ROM drive into the MultiBay, complete the following steps: 1. Turn off the computer. 2. Align the left side of the diskette drive or CD-ROM drive with the left