Home > Compaq > Notebook > compaq lte 5000 User Manual

compaq lte 5000 User Manual

    Download as PDF Print this page Share this page

    Have a look at the manual compaq lte 5000 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 65 Compaq manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							6. Remove the remaining three screws from the main board and the two
    screws from the CPU connector bezel (Figure 6-17). 
    						
    							7. Lift the main board out of the base. Begin lifting at the front edge
    of the board [1] . The CPU connector bezel [2] comes off with the board
    but is not attached to the board. Some manipulation is required around
    the PC Card door module (Figure 6-18). 
    						
    							Reverse the removal procedure described above to install the main board.
    Position the CPU connector cover in place but do not secure it with screws
    until the main board is properly seated. Then proceed with the rest of the
    installation.
    Chapter 6.9 CPU Connector Bezel 
    The main board must be removed to remove and replace the CPU connector
    bezel. See Section 6.8 for details.
    Chapter 6.10 MultiBay Assembly 
    The main board must be removed before removing a MultiBay assembly.
    The MultiBay assembly is spared as part of the top cover assembly.
    However, the Multibay assembly may need to be removed in order to access
    the MultiBay door assembly. To remove a MultiBay, complete the following
    steps:
    1. Remove the three screws and lift the bay out (Figure 6-19). 
    						
    							2. Begin lifting at the end of the assembly toward the MultiBay Connector
    Board and lift the MultiBay assembly out (Figure 6-20). 
    						
    							Reverse the above procedure to install a MultiBay assembly, inserting the
    end nearest the MultiBay door first (Figure 6-21). Take care not to damage
    the tabs on this end of the MultiBay. 
    						
    							Chapter 6.11 MultiBay Door 
    The main board and one of the MultiBays must be removed before removing
    the MultiBay door assembly. To remove a MultiBay door assembly, complete
    the following steps:
    1. Prepare the expansion base for disassembly as described in Section 6.3.
    2. Remove the bottom cover assembly as described in Section 6.5.
    3. Remove the power supply as described in Section 6.7 if servicing the
    door on that side.
    4. Remove the main board as described in Section 6.8 if servicing the
    door on that side.
    5. Remove the appropriate MultiBay assembly as described in Section 6.10.
    6. Remove the MultiBay door by flexing the door [2] away from the
    expansion base as shown in Figure 6-22. Note the orientation of the
    spring [1]; this is important since it maintains the door in a closed
    position. 
    						
    							Chapter 6.12 PC Card Door Assembly 
    The main board must be removed before removing the PC Card door assembly.
    The PC Card doors are spared as an assembly, mounted in a common frame. To
    remove and replace the PC Card doors, complete the following steps:
    1. Prepare the expansion base for disassembly as described in Section 6.3.
    2. Remove the bottom cover assembly as described in Section 6.5.
    3. Remove the main board as described in Section 6.8.
    4. Remove the three screws and lift the PC Card door module out of the
    bottom cover assembly (Figure 6-23). 
    						
    							Reverse the above procedure to install the PC Card door assembly.
    Chapter 6.13 Power Switch Board 
    The bottom cover assembly must be removed before removing the power switch
    board. The power switch board is installed as a unit with its cable
    permanently attached.
    To remove the power switch board, complete the following steps:
    1. Prepare the expansion base for disassembly as described in Section 6.3.
    2. Remove the bottom cover as described in Section 6.5.
    3. Disconnect the power switch board cable and ground wire from the main
    board (Figure 6-24). 
    						
    							4. Remove the screw holding the power switch board in place and lift the
    board out (Figure 6-25). 
    						
    							Reverse the above procedure to install a power switch board.
    Chapter 6.14 IrDA Board 
    The bottom cover assembly must be removed before removing the IrDA board.
    The IrDA board is installed as a unit with its cable permanently attached.
    To remove the IrDA board, complete the following steps:
    1. Prepare the expansion base for disassembly as described in Section 6.3.
    2. Remove the bottom cover assembly as described in Section 6.5.
    3. Disconnect the IrDA board cable and ground wire from the main board
    (Figure 6-26). 
    						
    All Compaq manuals Comments (0)

    Related Manuals for compaq lte 5000 User Manual