Comdial Large Screen Speakerphone Reference Manual

7.21 Using E and M Tie Lines
E & M tie line operation is typically used in applications where one
group of users often need to call parties located in one or more remote
locations. In these applications, your system is directly tied to another
similar system at the remote site(s).
If your system has been configured for tie line operation, the procedures
you use to place calls, transfer calls, and set up conference calls differ
slightly from other types of connections. These procedures are described
in...

NOTE: After transferring the call to the remote end of the E & M tie
line, you will have created an unattended conference, and your
telephone will appear as though it were on hold.
6.
PressTAPbutton to rejoin the transferred call.
7.
After rejoining the conference, press#to place the call on hold
again (creating another unattended conference) or hang up to
terminate the call.
* You can eliminate this step if the installer has configured your
system for quick transfer and you are accessing the E & M line...

·To drop out of a conference call between you and two outside lines
(creating an unsupervised conference),
1. Hand up (lines remain lighted and in use until one or both outside
parties disconnect).
·To rejoin an unsupervised conference between two outside lines,
1.
PressTAP.
NOTE: Conference volume levels depend on the quality of the external
lines.
7.22 Call Forward Outside System
The Call Forward Outside System (CFOS) feature allows you to forward
incoming or transferred line calls to telephone numbers...

·To deactivate CFOS,
1.
PressCFOSinteractive button.
—OR—
PressCFOSpreprogrammed button.
—OR—
PressINTERCOMand dial#5.
·To join an active CFOS call from the CFOS-enabled station,
1. Note flashing HOLD light indicating active CFOS call, and press
TAP. Join CFOS-forwarded party and CFOS destination in a
conference call.
Comdial has taken reasonable steps in the design of all product features,
including CFOS, which protect against unauthorized or fraudulent access
to, or use of, a system, or which protect...

7.23 Mark Problem Line
Your programmer can arrange the system so that you can mark a line that
is not functioning properly. You do this by pressing a preprogrammed
MARKbutton or by dialing a feature code of your choice. After you
have marked a particular line a programmed number of times, the system
takes the line out of service (unless programmed to prevent this from
happening). When the system takes the line out of service, it logs the
condition and triggers an alarm. The printed error log will then...

7.24 Automatic Set Relocation
If your installer has equipped your system with automatic set relocation,
when you move your telephone to a new location, the system will give
you a choice (through a display prompt) as to whether you want to keep
your previous programming or use the programming in the new location.
·To maintain the extension number and programming features from
the old location,
1. Connect the telephone line cord to the new jack.
2.
PressYESto retain the extension number and programming...

7.25 Using The IMIST Module
Impact SCS8412F-**, and 8412S-** speakerphones equipped with the
optional IMIST module can support an IST device (modem, FAX
machine, industry-standard telephone, etc.) in addition to the LCD
speakerphone. Depending on system programming, the IST device may
be used to make outgoing calls and receive incoming calls.
The functionality of the IMIST module depends on the type of system
you are using.
•The IMIST module will function on a DXP system with the
appropriate digital...

7.26 Using The Caller ID Feature
The Caller ID feature allows you to view incoming call numbers before
you answer them. Incoming call numbers flash in the lower half of the
LCD. If you answer the call, the number appears in the upper half of the
LCD.
The system also stores numbers that ring on your line but receive no
answer. The system indicates that it has stored ring-no answer numbers
by causing the CID light on your telephone to flash. Pressing theCID
button allows you to view the stored numbers one...

7.27 Viewing The Call Log
The Call Log feature allows you to view the last 10 outgoing calls made
from your station. If you have caller ID, the LCD will also display
incoming calls. Incoming calls are designated with anInext to the
number and outgoing calls are designated with anO.
·To view the call log,
1.
Press theOPTIONSbutton.
2.
Press theCALL LOGbutton.
The LCD displays the last 10 phone numbers you dialed (or the
numbers that called you, if you have caller ID). Incoming calls
are designated with...

This page remains blank intentionally.