Home > Comdial > Communications System > Comdial Dxp Plus Instructions Manual

Comdial Dxp Plus Instructions Manual

Here you can view all the pages of manual Comdial Dxp Plus Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 621

3.2 Programming The DVA Parameters
3.2.1 Programming Intercoms For DVA Messages
DescriptionFor each message type, you can assign up to ten intercom numbers and assign a single access
digit to each of these intercom numbers. You can assign feature codes as well as intercom
numbers. For example, if you have installed the Tracker Paging System option, you can program
the Tracker Pager access code (S8) to an appropriate message and assign a single-digit dialing
code to the access code. This allows DISA...

Page 622

3.2.3 Recording The DVA Messages
Description:You or the system attendant must record the messages that the DVA plays to the callers. You do
this in one of two ways: either by delivering them from the telephone handset at the attendant
station or by playing the contents of a professionally-supplied tape recording into the DVA
memory. Each DVA stores up to four unique messages. The total message storage time is two
minutes and you can divide this time as necessary among the four messages or use the entire...

Page 623

3.2.4 Editing The DVA Messages
Description:After DVA messages exist, you can play them, copy them, and delete them as necessary using the
following attendant programming.
Programming:To play a previously recorded DVA message,
1. Press INTERCOM and dialS#0S062.
2 Dial 10–43 to choose message type.
3. Listen as system automatically plays the message for verification at your
attendant station.
4. Press#to stop verification playback.
5 Dial 10–43 to choose next message type to hear.
To copy a previously...

Page 624

Installing And Programming ExecuMail Equipment
On The DXP Plus Digital Communications System
This installation instruction gives you information for connecting the ExecuMail voice processing system to the
DXPPlusdigital communications system.
The introductory section familiarizes you with the ExecuMail option and the literature supplied with it. The
remaining sections explain ExecuMail installation details through the various station boards and
Comdial-produced interface devices. The following list shows...

Page 625

2.0 Installing The ExecuMail System
At Analog Station Ports
When you interface the ExecuMail system to the DXPPlussystem through the analog station ports on its analog
station board, you must place the Comdial Voice Mail Interface device (VMI–X) between the ExecuMail ports
and the system’s station ports. The VMI–X includes two circuits; therefore,you will need one device for every
two ExecuMail ports that you plan to connect. This means that for a four-port ExecuMail system, you will
need two VMI–X...

Page 626

AW1002
7.0
11.50
8.75
10.25
3.0
Detailing The VMI–X Dimensions
BOTTOM
OF
HOUSINGLEFT SIDE
OF HOUSING
A
B
D
CLOSED
OPEN
AW1001
Setting The VMI–X Configuration Switches
Installing And Programming For ExecuMail IMI89–206
Installing And Programming For ExecuMail – 3 

Page 627

2.3 Connecting the VMI–X
·Route the necessary cabling, and connect the VMI–X device between the ExecuMail system and the station
ports per the connections detailed in the diagram shown on the next page.
·Use two-pair (four-wire) cable between the station port connection block and the VMI–X device.
·Use one-pair (two-wire) cable for each VMI–X termination jack.
·Use two-pair (four-wire) cable between the ExecuMail system and the VMI–X termination jack.
·The VMI–X requires a grounding wire that is separate...

Page 628

Interconnecting The VMI–X
Installing And Programming For ExecuMail IMI89–206
Installing And Programming For ExecuMail – 5 

Page 629

3.0 Installing The ExecuMail System
At Digital Station Ports
When you interface the ExecuMail system to the DXPPlussystem through the digital station ports on its digital
station board, you must place the Analog Terminal Interface Device (ATI–D–1PT) between the two systems. The
ATI-D-1PT includes one circuit; therefore,you will need a separate device for every ExecuMail port that you
plan to connect. This means that for a four-port ExecuMail system, you will need four ATI–D–1PT
devices.The ATI–D–1PT is...

Page 630

Outline Dimensions
(In Inches)Spacing For
Mounting Hardware
(In Inches)
AW139
Detailing The ATI–D–1PT Dimensions
Installing And Programming For ExecuMail IMI89–206
Installing And Programming For ExecuMail – 7 
Start reading Comdial Dxp Plus Instructions Manual

Related Manuals for Comdial Dxp Plus Instructions Manual

All Comdial manuals