Comdial Dxp Plus Instructions Manual

2.3 Connecting The Equipment
Connect the cabling to the ATI-D-1PT per the diagram shown on the next page
CAUTION
Be careful when connecting the wiring between the DXP Plus and the ATI-D-1PT. Be sure to connect the
digital station port to the COMMON EQUIPMENT (KSU) jack on the ATI-D-1PT. Damage to the
ATI-D-1PT could occur if this wiring is mistakenly connected to the IST jack.
·While a grounding wire is not required for operation, one is desirable for decreasing radio frequency
interference and...

·Plug a modular cord into the telephone jack on the adapter and connect the opposite end of the cord to the OPX
line.
·Plug the adapter power cord into a standard 117 VAC, 3-wire electrical outlet.
Interconnecting The ATI–D–1PT
Installing And Programming For ATI–D–1PT IMI89–208
Installing The ATI–D–1PT – 7 

3.0 Programming For Analog Terminal Interface Operation
The ATI-D-1PT provides the interfacing capability required to connect most industry standard telephone (IST)
equipment to a digital station port of the digital communications system.
The IST provides basic intercom service coupled with the ability to access outside lines. You can program the
station port (through which the IST is being interfaced via the ATI-D-1PT) for either prime intercom operation or
prime line automatic and idle line preference...

3.5 Programming Procedures
The ATI-D-1PT automatically identifies itself as an analog terminal interface for the digital station board as soon
as you connect it to the digital communications system.
Prime Line Programming
Prime Line Type
When you enable this feature, the station automatically selects a line, line group, or intercom number for use when
the station user takes the station off hook. Use the programming procedures shown below to select the line port,
line group, or intercom number to serve as...

Idle Line Programming
Idle Line Preference
With you enable this feature, a station automatically connects to an idle line when the user lifts the telephone’s
handset.
1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select COS programming and press ENTER.
4. Type class of service number (1-32) and press ENTER.
5. Fro COS programming menu, type item number for feature and press ENTER.
6. Press SPACE bar for feature setting.
7. When finished,...

Dialing Mode
Program the line port to match either a DTMF tone or a rotary (pulse) dialing line as supplied by the central office
(CO).
1. Press CONTROL T for main menu.
2. From main menu, select lines and press ENTER.
3. From lines menu, select line programming and press ENTER.
4. Type line port number or name and press ENTER.
5. From line programming menu, type item number for feature and press ENTER.
6. Press SPACE bar for feature setting and press ENTER to accept setting.
7. When finished, press...

Flexible Ringing Assignments
Program ringing assignments on a per station/per line/per intercom number basis.  Ringing can be immediate,
delayed, or special purpose. Use the procedures in this section to customize the ringing features for the system.
Direct Ringing
Use this procedure to choose the line ports that you want to ring at a station as soon as a call appears. Direct
ringing sounds during the day 1 and day 2 time periods but does not ring during the night ringing mode or during
the manual night...

Day 1 Ring
Use this procedure to choose the line ports that you want to ring at stations during the day 1 ringing mode time
period. Refer to the paragraph below titled, Day 1, Day 2, and Night Ringing Begin and End Times, to set the
beginning and ending times of this ringing.
1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select station programming and press ENTER.
4. Type personal intercom number or previously assigned name and press ENTER....

Night Ring (Night Transfer - Of Ringing)
Choose the line ports that you want to ring, along with the delayed ringing line ports, at stations during the night
ringing mode of operation. The ringing arrangement that you configure here is the arrangement that is active both
during the automatic night ringing time period and whenever the attendant manually activates the night transfer
(of ringing) operation. Do note that the attendant commanded night ringing period supersedes the automatic night
ringing...

Personalized Ringing Tone
Program a station to ring in one of several distinctive tones for proprietary digital telephones and in one of four
distinctive tones for analog telephones.
1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select station programming and press ENTER.
4. Type personal intercom number or previously assigned name and press ENTER.
5. From the station programming menu, type item number for feature and press ENTER.
6. Type...