Comdial Dxp Plus Instructions Manual

3.1 Connecting the ATI-D-1PT
·Route the necessary cabling, and connect the ATI–D–1PT device between the ExecuMail system and the digital
station ports per the connections detailed in the diagram shown on the next page.
·Use one-pair (two-wire) cable for all connections.
CAUTION
Be careful when connecting the wiring between the DXP Plus and the ATI–D–1PT. Be sure to connect
the digital station port to the COMMON EQUIPMENT jack on the ATI–D–1PT. Damage to the
ATI–D–1PT could occur if  you mistakenly...

Interconnecting The ATI–D–1PT
Installing And Programming For ExecuMail IMI89–206
Installing And Programming For ExecuMail – 9 

4.0 Installing The ExecuMail System
At Industry-Standard Telephone Station Ports
When you interface the ExecuMail system to the DXPPlussystem through the industry-standard telephone
station ports on its industry-standard station board, you do not need an interface device; however,you will need a
station port for every ExecuMail port that you plan to connect.  This means that for a four-port ExecuMail
system, you will need four IST station ports.
4.1 Connecting the ExecuMail System
·Route the necessary...

Interconnecting ExecuMail Directly To DXP Plus
Installing And Programming For ExecuMail IMI89–206
Installing And Programming For ExecuMail – 11 

5.0 Programming For Voice Mail Operation
After connecting an voice mail system to the DXPPlussystem, program the DXPPlusto operate properly with it
using the procedures detailed below. They are presented here in a typical order of progression but you can
perform them in any order that is convenient.
5.1 Arranging Station Ports For Voice Mail Use
Description:After you or your installer has connected voice mail ports to the system station ports through the
appropriate interface devices (for example, the...

5.3 Arranging Voice Mail Call Transfer Parameters
5.3.1 Automatic Attendant Transfer On Busy
Description:You can enable automatic attendant transfer on busy for individual station ports if you wish.
With this feature enabled, the system will ring a busy telephone when the voice mail system is
attempting to transfer a call to it thus giving the user the option of leaving his or her present call
and taking the new one. With the feature disabled, the busy telephone is not signalled by the
presence of a new...

5.4 Assigning Transfer-To-Voice Mail Button
Description:A system user can use a pre-programmed button to transfer an incoming call directly to a voice
mail box so the caller can leave a message. You must use the button mapping programming
procedure to assign this Transfer-To-Voice Mail button at a system telephone.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select button mapping and press ENTER.
4. Type prime intercom number or...

5.6 Assigning Voice Mail Identification (ID) Number
Description:As an option, you can assign an identification number to each DXPPlusline so that the voice
mail system can provide customized call handling on a per line basis. Use voice mail system
programming to match this ID number to a particular personal directory or transaction box within
the voice mail system.  When the DXPPlusroutes a call that is ringing at a particular line to the
voice mail system to be answered, it routes it with the ID number....

5.8 Setting The Voice Mail Integration Digits
Description:You can choose the DTMF digits that the DXPPlussends to a voice mail system. A voice mail
system uses these DTMF digits to determine system and station status so that it can properly
process a call. You must be versed in your voice mail’s requirements before you can assign
DTMF integration digits in the DXPPlus. The system defaults the voice mail parameters to
match the Comdial voice mail system. Certain applications in countries with dialing...

5.8.1 Programming The Voice Mail Integration Digits
Programming:1. Press CONTROL T for main menu.
2. From main menu, select peripherals and press ENTER.
3. From peripherals menu, select voice mail and press ENTER.
4. From the voice mail menu select integration digits and press ENTER.
5. From the integration digits menu, type row number for item and press ENTER.
6. Type entry and press ENTER.
7. Repeat step 6 until finished.
8. When finished, press ESCAPE twice.
9. Type y to accept changes, n to reject...