Comdial Dxp Plus Digital Communications System Instructions Manual

/M/66-123DXP Plus Programming lnsfrucfisns
7.1‘46Enhanced LCD Display
Description:Take this programming action to enhance the display of an LCD-equipped telephone so that it
shows both the name of the calling station and its personal intercom number.Programming: 1 
D
2.
3.
4.
5.
6.
-7.
8.
9.
Press CONTROL T for main menu
From main menu, select stations and press ENTER.
From stations menu, select COS programming and press ENTER.
Type class of service number (l-32) that corresponds with class of service...

DXP Plus Programming instructions
7.2Programming Station Features
lMl66-123
7.2.1Personal lnfercom Number
Description:Use this programming procedure to change the station’s personal intercom number.
Also refer to 
Section 9. I.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select station programming and press ENTER.
4. Type personal intercom number or previously assigned name and press ENTER.
5. From station programming menu, type...

/M/66-123BXP Pius Programming Instructions
7.2.3Class Of ServiceDescription:
Programming:
You can assign a group of preprogrammed class of service station features to a station. The
system makes up to 32 different classes of service available, and you can program the feature
values differently in each one.
1~ Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select station programming and press ENTER.
4.Type personal intercom number or previously...

DXP Plus Programming instructionsIMB-123
7.2.5Idle Line PrioritvDescription:
If you use Section 7.1.14 to give a station the ability to automatically connect to an idle assigned
line when the user takes the handset off-hook, take this programming action to set the priority in
which the system chooses the idle lines for use. You can place up to eight lines in this priority
list.
Programming:1 0 Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select...

7.2.7Group Intercom Access
Description:Use this procedure to add group intercom numbers to stations for their use. Also refer to
Section 7.3 to map buttons for group intercom number selection. See Section 9 for other
intercom number considerations.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select station and press ENTER.
3. From station menu, select station programming and press ENTER.
4. Type personal intercom number or previously assigned name of station being programmed
and...

DXP Plus Programming InstructionsIMIH-123
7.2.8Prime Line Programming
Prime Line TypeDescription:
When you enable this feature, the station automatically selects a line, line group, or intercom
number for use when the station user takes the station off hook. Use the programming
procedures shown below to select the line port, line group, or intercom number to serve as the
prime station calling interface.
NOTE: You can create an intercom hot line telephone by taking special programming action
when you...

/M/66-723DXP PIUS Pfogramming Instrwctions
Prime Line Group
Description:Use this procedure to choose the prime line group.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select station programming and press ENTER.
4. Type personal intercom number or station name and press ENTER.
5. From station programming menu, select prime line group and press ENTER.
6. From prime line group menu, type 1-16 and press ENTER.
7. When finished,...

DXP Plus Programming InstructionslMl66-123
7.2.9Tone Or Voice Signalling (Tone First)Description:
Intercom calls are either tone or voice signalled as a first choice with the other mode available
as a second choice. Use this procedure to select the first choice in intercom signalling on a per
station basis.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select station programming and press ENTER.
4.Type personal intercom number or...

/M/66-123DXP Plus Programming instructions
Z2. IIDefault Forward TypeDescription:
Use this procedure to arrange the call forward default scheme for individual stations. With this
feature, the system will automatically forward ringing calls to another station after a preset
number of rings.Since this is an automatic forwarding of the calls, the station users do not have
to take any action; however, any user-enabled call forwarding (Section 
7.1.5) that they take at
their stations will override this...

DXP Plus Programming InstructionsIMIW-123
7.2.12Forward RNA Ring Busy (Enhanced Call Forwarding)Description:
The call forward feature allows a station user to choose to receive several rings for RNA calls
before the system forwards them. At default, the system immediately forwards calls that reach a
busy station. You can take this programming action to allow calls to a busy station to ring in a
subdued manner before they forward if the user chooses them to do so. This subdued ringing of
calls to a busy...