Comdial Dxp Plus Digital Communications System Instructions Manual

/M/66-123DXP Plus Programming Instructions
7.1.29Remote Station DisableDescription:
The remote station disable feature, when enabled, allows users at stations with the proper class
of service to dial a code and remotely disable or enable another station. Normally, you should
give this capability to the system attendant but you can assign it to any class of service that is
appropriate.
Programming:1 D Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu,...

7.1.31Line AnswerDescription:
This feature provides station access to a line for call answering purposes for an entire class of
service of stations. Also refer to 
Section 7.1.32. You must turn on both that feature and this one
for a line to be fully usable.
Programming:1.Press CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select COS programming and press ENTER.
4.Type class of service number (l-32) and press ENTER.
5.From COS programming menu, type...

lMl66-123DXP Pius Programming Instructions
7.1.33Periodic Line Tone
Description:This when enabled, provides periodic warning tones to station users while they are busy on
certain lines. The warning tone consists of one 500 ms burst, a 100 ms off period, and 
one100
ms burst. The tone reminds the users to 
keep their conversations short on these lines. You can
enable this feature for a class of service of telephones and then specify the particular lines that
you deem applicable. Further, you can select...

7.1.34Maximum Call Duration
Description:The system provides the maximum call duration feature. This feature, when enabled,
automatically cuts off calls on certain lines after a preprogrammed time. The system will not cut
off calls made to an emergency number (Section 
10.4). The system sounds a warning tone at the
busy station 10 seconds before it disconnects the call. The warning tone consists of one 800 ms
burst followed by eight 100 ms bursts. Also refer to Section 7.1.33 for a related feature....

lMl66-123BXP Plus Programming Instructions
7.7.35Line Group Access
Description:Use this procedure to give a station access to line groups. Refer to Section 8.2 for other line
group considerations.
Programming:1 0 Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select COS programming and press ENTER.
4. Type class of service number (l-32) and press ENTER.
5. From COS programming menu, type item number for feature and press ENTER.
6. Type line...

7.1.37Line-To-Line Transfer (Unsupervised Conference)Description:This programming feature gives a station the ability to set up an unsupervised conference
between two lines.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select COS programming and press ENTER.
4. Type class of service number (l-32) and press ENTER.
5. From COS programming menu, type item number for feature and press ENTER.
6. Press SPACE bar for feature setting.
7....

/M/66-123DXP Plus Programming Instructions
7.1.36Voice Announce BlockDescription:
When you enable this programming feature a station has the ability to block voice announced
internal signalling when its user dials the proper code.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select stations and press ENTER.
3. From stations menu, select COS programming and press ENTER.
4. Type class of service number (l-32) and press ENTER.
5. From COS programming menu, type item number for feature...

7.1.40Forced Account CodesDescription:
After you have enabled the account code feature for the system, set its parameters, and
programmed its list of account codes into the system, turn the feature on for a station class of
service and make it either forced or optional.If you make it a forced account code, the user
must enter an account code before the system will let him or her dial the number for an outgoing
call.Also, on incoming calls a user must enter an account code before the system will allow
him...

/M/66-123DXP Pius Programming instructions
7.1.42Clear Major Alarm RingDescription:
This feature allows users to clear the major alarm ring condition from a telephone station. To
make this feature available to users, you must first program a class of service as described
below and then assign that class of service to the user’s telelphone station.Programming:
1.Press CONTROL T for main menu.
2.From main menu, select stations and press ENTER.
3.From stations menu, select COS programming and press ENTER....

DXP Plus Programming InstructionsIMl66-123
7.1.44Restrict A RS Hookflash
(Automatic Route Selection, Hookflash Restriction)
Description:This feature enhances ARS response to hookflash action on an outside line when that action is
followed by dialed digits. With the feature enabled, the system delays response to a hookswitch
flash until after the ARS feature verifies as valid all subsequent dialed digits. With the feature
disabled, the system sends the hookflash over the line without waiting for the ARS...