Comdial Dxp Plus Digital Communications System Instructions Manual

DXP Plus Programming lnsfructions/M/66-123
6.8.5Timed Recall (Held And Transferred Calls)
Attendant Hold RecallDescription:After a call has been on hold at an attendant station for a programmed length of time, the call
recalls to the attendant station. Use this procedure to set the amount of time before a held call
recalls at an attendant station.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select system and press ENTER.
3. From system menu, select timing and press ENTER
4. From...

/M/66-123DXP Plus Programming Instructions
6.8.6Paging Access
Description:If you have assigned a paging zone and given that zone access to external paging equipment
(Section 6.101) plus enabled paging transmit capability (see Section 6.10.3) at a station, that
station has access to external paging equipment. With this paging access procedure, you can set
the maximum length of time that a station can stay connected to the external paging equipment.
This timing setting also controls the amount of time a...

DXP Plus Programming Instructions/M/66-123
6.8.9Periodic Tone TimeDescription:After you enable the periodic warning tones that remind users to keep conversations short on
certain outside lines (Section 
7.1.33), use this procedure to set how often that you wish the
periodic warning tones to occur
Programming:1. Press CONTROL T for main menu.
2. From main menu, select systems and press ENTER.
3. From system menu, select timing and press ENTER.
4. From system timing menu, type item number for feature and...

/M/66-123BXP Plus Programming Instructions
6.8.12Line-To-Line Connect Duration
Description:After you have given a station the ability to set up an unsupervised conference between two
lines (Section 
ZI.37), you should use this procedure to set the maximum amount of time that an
unsupervised conference can continue between two lines. When the time out occurs, the system
recalls the station from where the user enabled the unsupervised conference.
Programming:1~ Press CONTROL T for main menu.
2. From main...

6.8.15Authorization Code TimeoutDescription:
Use the Section IO.5 procedure to enable the authorization code feature. Once a user uses the
authorization code to access his or her telephone features, those features remain in effect until
any idle time at the telephone exceeds the authorization code time-out period that you program
with this feature.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select system and press ENTER.
3. From system menu, select timing and press ENTER.
4. From...

/M/66-123DXP Plus Programming Instructions
6.8.18/ST Flash TimeDescription:
Programming:
You can program the timed length of the signal that results when a user of an industry-standard
telephone presses and releases the telephone hookswitch (or presses the TAP button if available
on his or her telephone) on a system-wide basis. Often, a signal with a short time length
(typically 500-750 ms) serves to alert the system to receive a feature code (flash) while a signal
with a long time length (typically...

6.8.20Pulse Dial lnterdiait TimeDescription:
You can set the interdigit time between dial pulses when the system pulse-dials a number over a
line. The DXP 
Plus defaults this time to 150 msec. and provides a range of timing values
between 100 msec. and one sec. that you can set in either 50 or 100 msec. increments. Refer to
Section 8.1.9 to enable pulse dialing.
Programming:1. Press CONTROL T for main menu,
2. From main menu, select system and press ENTER.
3. From the system menu, select timing and press...

/M/66-123DXP Pius Programming Instructions
6.9Svsfem Parameters
6.9. ISvnchronized Rinuin~Description:
The system can provide an audible distinction between internal and external call ringing when
needed. Enable or disable that feature with this programming procedure. When you enable this
feature, line call ringing sounds the same cadience as intercom calls. This feature does not apply
to direct inward dial lines (Section 8.4) and E&M lines (Section 8.7)*Programming:
1 s Press CONTROL T for main menu.
2....

DXP Plus Programming instructions/M/66-123
6.9.3A utomafic Roufe Selection (A RS Enable)
Description:You can enable or disable automatic route selection on a system-wide basis. A defaulted
system has ARS disabled. Refer to 
Section 12 for other ARS programming details.
Programming:1. Press CONTROL T for main menu.
2. From main menu, select system and press ENTER.
3. From the system menu, select system parameters and press ENTER.
4. From the system parameters menu, select ARS feature and press ENTER.
5....

/M/66-123DXP Plus Programming hstructions
6.9.5Toll A RS Dialing PauseDescription:
To create toll restriction parameters for the system, program restricted numbers as entries in the
toll restriction table using programming details provided in Section 11.6. From that discussion,
learn about entering a pause as part of the restricted number’s digit string. Use the following
programming procedure to enable the system to accept that pause entry at the end of a restricted
number’s digit string....