Comdial Dxp Correspondance Instructions Manual

DXP Correspondence ManualSMDALSMDR Programming
Account Code (System Parameters)Account codes are used to identify calls by category, so that the
system can record costing by that category. You can arrange the
system to force the user to enter an account code and have the system
verify it before it allows the user to make a call. Turn on the account
code feature for the entire system using this procedure. Also, enable or
disable system verification of the entered code. If you enable
verification, the...

SMDALSMDR ProgrammingDXP Correspondence Manual
SMDA Attendant Delete
Use this programming feature to provide the system attendant with the
ability to delete SMDA records from the system memory.
SMDABMDR Printer Port
Use this programming feature to determine the serial data port through
which the system will route its generated 
SMDALSMDR.
Report OptionYou can arrange for the 
SMDRLSMDA parameters to convey either
the cost of calls that the stations make or the amount of time that lines
have been on hold...

DXP Correspondence ManualSMDALSMDR Programming
10.3
Automatic
Reports (SMDA)Program the system to automatically provide call cost reports for
printing.- Choose the day and time that the printout is desired.
- Choose the type and detail of each report.
- Dictate whether the call records are to be erased from the system
memory after they are printed.
The SMDA feature allows the system to store various call records and
generate reports of these records for printout. These reports include
either station,...

Add, Remove, Display Account CodesUse this procedure to assign up to 1000 account codes (each up to 16
digits in length-see Section 
10.3.3). Alternately, use this procedure
to remove previously assigned account codes from the system. Add or
remove one account code at a time or an entire block of account codes
all at once. To assign numbers that user’s can dial without entering an
account code, refer to section 10.4.
Account Code (For Class Of Service)
After you have enabled the account code feature for...

DXP Correspondence ManualSMDABMDR Programming
10.4
Emergency
Numbers
10.5
Authorization
CodeWhen the system requires an account code, a telephone user must
enter it before the system allows him or her to dial a number; however,
the system does not require an account code prior to allowing a
telephone user to dial a designated emergency number. Use 
thi’sprocedure to list the designated emergency numbers. The system
accepts a total of 16 numbers. Each number can be up to 16 digits long.
Authorization...

SMDAISMDR ProgrammingDXP Correspondence Manual
Chapter Ten
Review1. The DXP automatically provides an SMDA report whenever
the costed-call storage reachespercent?
Questions2. You can set the DXP to report SMDA information sorted in
four different ways:
3. The DXP always includes the dialing time in costing a call; true
or false?
4. Account codes can only be used on outgoing calls; true or false?
5. An account code can be a maximum ofdigits.
6. Changing the account code length automatically deletes all...

DXP Correspondence ManualSMDNSMDR Programming
9. You can program a maximum of
DXP.account codes in the
10.If you have programmed forced account codes for each
station, those station users must dial the account code for any
outgoing calls; true or false?
11.A user can enter his or her authorization code at a telephone
and override that station’s authorization code and features;
true or false?
SMDALSMDR Programming 10 - 9 

DXP Correspondence ManualChapter Con tentsII 1
Toll RestrictionChapter Eleven: Toll Restriction
~.................................,......................11-I
11.1
11.2
11.3
11.4
11.5Introducing Toll Restriction...............................................................
11-lRestriction Levels...............................................................................
11-2Toll Groups.........................................................................................
11-3Restricted...

DXP Correspondence ManualToll Restriction ProgrammingToll Restriction
II.1
IThe toll restriction/automatic route selection option is located on theIntroducing Tollmain menu as “Toll 
/ ARS.” And while the two features are grouped
together in programming, this correspondence manual separates them
Restrictionfor added explanation. Chapter Twelve covers the automatic route
selection feature.
With the toll restriction feature, the system allows or denies outgoing
line calls to selected users over selected...

Toll Restriction PrOgrammingDXP Correspondence Manual
11.2
IThe restriction table sets up the test structure to determine whether aRestrictionparticular station can or cannot make a call. The restriction table
allows a maximum of 400 entries; broken down into 10 entries on a
Levelspage. You assign each entry a value from 1 to 8, or with “alloti all” or
“deny all.” The “allow all” entry ensures that the system applies no
dialing restriction to a number (example: 911). The “deny all” ensures
that a station...