Comdial Dxp Correspondance Instructions Manual

DXP Correspondence ManualLine Programming
10. DIDLDNIS will not support Delay Ring, Day 1 ring, or Day 2
ring; true or false?
11. DISA allows outside callers to call directly into the DXP; true
or false?
Line Programming 8 
- 21 

Intercom NumbersChapter Nine: Intercom
Numbers. ..‘...................................................,..9-1
9.1Introducing Intercom Programming.....................................................9-l
9.2Modifying Intercom Numbers..............................................................9-2
9.3Adding Intercom Numbers...................................................................
9-3
9.4Removing Intercom Numbers.............................................................
9-3
9.5Renumbering...

DXP Correspondence Manual
Intercom ProgrammingIntercom Numbers
9. IThe system provides a maximum of 600 intercom slots with 192 slots
Introducingset up as personal intercom numbers and up to 408 group intercom
numbers. Group intercom numbers are four digits and begin with
Intercomnumber 3 101. At default, the blocks of intercom numbers are assigned
Programming 
as follows’101-292 = personal intercom numbers
3101-3292,4101-4292,5000-5023 = group intercom numbers
5024-5999 = unassigned-used for renumbering...

9.2
Modifying
Intercom
NumbersUse this programming procedure to modify intercom numbers and
station names. A display name is composed of a maximum of seven
characters and shows in the display of an LCD speakerphone as an
identification aid. A full name is composed of a maximum of 20
characters and shows in some voice mail and open architecture
interface applications. You can compose a valid name from any
alpha-numeric character; however, the first character of a display
name must be an alphabetic...

A9.3.dding Intercom
Numbers
9.4
Removing
Intercom
NumbersUse the procedure to add intercom numbers or to add group intercom
numbers to stations for their use. Also refer to Section 7.37 to map
buttons for group intercom number selection.
.
INOTE: Use the Intercom Hunt List feature to place personal
intercom and group intercom numbers in a list. Calls to abusy hunt list number will search the list for an idle
number at which to ring. You can enter up to eightintercom numbers in a hunt list; these can be...

9 5Use this procedure to renumber one intercom number or a block of
RenUmberi&intercom numbers. If you renumber an intercom number, be sure that
you do not use the old intercom number in button mapping, hunt lists,
ln tercomcall forwarding and similar applications,.
Numbers
9 - 4 hfercom Programming 

DXP Correspondence ManualIntercom ProgrammingChapter Nine
Review1. At default, intercom number 5000 is designated for what
purpose?
Questions.
2. The system defaults the station ports and personal intercom
numbers beginning with the right-most station board; true or
false?
3. Group intercom numbers are alwaysdigits long.
4. The first character of a station display name must be a
.5. You must remove intercom numbers one at a time; true or false?
Intercom Programming 9 
- 5 

DXP Correspondence ManualChapter Con tentsSMDABMDR
Chapter Ten: SMDAEMDR. . . . . . . . . . . ..‘....................................................1 O-l
10.1Introducing SMDABMDR Programming.........................................10-l10.2 
SMDABMDR Parameters.................................................................10-2Dial Time Limit
.........................................................................1 o-2AnswerTimeLimit.....

L10
SMDNSMDR
10.1
Introducing
SMDALSMDR
ProgrammingThe system automatically provides an SMDA report whenever the
costed-call storage reaches 95 percent of capacity. The programmer
can arrange the system to print the reports automatically at a specific
time. The attendant can view the number of free records or delete all
stored records. Deleting all stored records ensures that the system is
storing only the latest SMDA reports and provides a known starting
point for record storage.
There are four...

SMDAISMDR Programming
DXP Correspondence Manual
10.2SMDNSMDR
ParametersDial Time Limit
The system does not cost dialing time when it records the time-of a
call for costing purposes. You can program the amount of time that the
system waits before costing a call. Refer to section 12.5 for related call
costing information.
Answer Time Limit
Program the amount of time that the system waits before beginning to
cost a call. This time allows for a call to ring and be answered before
being costed. Refer to...