Comdial Dxp Correspondance Instructions Manual

DXP Correspondence ManualAutomatic Route Selection12.6
Automatic Route
Selection for
Speed Dial
NumbersYou can arrange for the system to process the system speed dial, and
any personal speed dial numbers, that you program for the users,
through the automatic route selection (ARS) feature. If the users
program their own personal speed dial numbers and you have enabled
ARS processing of calls, they must prefix their personal speed dial
numbers with the ARS preselect code.
If you are using DISA with ARS,...

Automatic Route Selection
DXP Correspondence ManualChapter Twelve
Review1. You cannot use call costing with ARS; true or false?
Questions-2. The ARS feature uses a different entry table from the toll
restriction feature; true or false?
3. At default, the DXP has ARS enabled; true or false?
4. Direct line selection bypasses ARS; true or false?
5. The route table specifies the following three parameters:
6. What is the “match any digit” symbol used by the DXP?
7. You can program a maximum of
table.routes...

DXP Correspondence Akmua~Automatic Route Selection
9. The DXP can cost both incoming and outgoing calls; true or
false?
10.You cannot use speed dials with ARS; true or false?
Automatic Route Selection 12 
- 9 

DXP Correspondence ManualChapter Contents113
System Printouts
Chapter Thirteen: System Printouts. . . . . . . . . . . . . . . . . . . . . . ..~..........................13-1
13.1Introducing System Printouts.............................................................13-113.2 Identifying System Printouts..............................................................
13-2Chapter Thirteen Review Questions...................................................
13-3Chapter Con tents 

DXf Correspondence ManualPrintouts
L13
System Printouts
13.1
Introducing
Sys 
tern PrintoutsIThe system makes a wide variety of printout records available. Use
this programming procedure to choose the user’s desired printout
types and to direct the printouts to either the 
ShIDA/SMDR data
printer or the VDT screen.
NOTE: Press CONTROL C to stop a printout to the VDT screen when
necessary. This action will not stop printout to a data printer.
Printouts
1. system
2. Station
3. Lines
4.Intercom Numbers...

PrintoutsDXP Correspondence Manual13.2
Identifying
System PrintoutsYou can choose to printout information in any of the following
categories:
1. System
2. Station
3. Lines
4. Intercom Numbers
5. SMDA 
/ SMDR
6. Toll 
/ ARS
7. Peripherals
8. Complete System Data
9. Abort Printouts
Printouts 13 
- 2 

DXP Correspondence ManualPrintoutsChapter Thirteen
Review1. You can send SMJJAEMDR reports to one of two devices,
what are they?
Questions.
I2. Chapterprovides further SMDALWDR information.
3. Pressing 
CTRL C stops a data printout to the printer; true or
false?
Printouts 13 
- 3 

DXP Correspondence ManualChapter Con tentsDiagnosticsChapter Fourteen: Diagnostics
...........................................................14-1
14.1IntroducingDiagnostics......................................................................14- 1
14.2Initialize Diagnostic Data...................................................................14-2
14.3ROM Checksum Verification.............................................................
14-2
14.4Scratch RAM...

DXP Correspondence ManualDiagnosticsDiagnostics
14.1The DXP provides you with the option of doing several different types
Introducingof diagnostic checks on the system. This chapter details the types of
diagnostics and their functions.
DiagnosticsNOTE: You shouldpetionn all diagnostic tests on an idle system and
I
under the direction of a Comdial technician. A busy system
could produce invalid test results. Because there 
are numerous
items that could contribute to a failure of any of these tests,...

14.2
Initialize
Diagnostic Data
14.3
ROM Checksum
Verification
14.4
Scratch RAM
TestThis option clears all previous diagnostic test results from memory.
The ROM checksum test calculates and displays a checksum to test
the integrity of the system software EPROMs.
This test checks the integrity of the scratch RAM area by writing and
reading words in memory. The test works by writing a known pattern,
“55AA” into memory and then reading the area of memory back. The
system then writes and reads a second known...