Home > Comdial > Communications System > Comdial Digital Telephone System Instructions Manual

Comdial Digital Telephone System Instructions Manual

Here you can view all the pages of manual Comdial Digital Telephone System Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 161

System ProgrammingIntegrated Call Costing Configuration 
- continued
Call Costing Programming Procedures
IMl66-107
when it records the time of a call for
costing. You can program the amount of
time that the system ignores for dialing
purposes.to program dial time limit.
3. Dial time in tenths of a minute 
(001 - 999.
or dial 000 to clear).“XxXx u
4. Dial G#+ for next SMDA feature.
5. Dial 
C# +# for configuration mode.
To change setting, repeat procedure and make different selection.
You can program the...

Page 162

IMl66-107System ProgrammingSpecialized Route Access (SRA) Configuration
0 To make a record of the programming configuration, mark the desired requirements in the records chart.
0 Use the sequence of steps listed below to program for the specialized route access (SRA) feature using your
VDT. 
You can on/y program the SRA feature from the VDT and not from station 10.
Enable The SRA Feature: 
The SRA1. Type I + 7 4 6 +N and press RETURN,
feature allows the system to select a line2. From the main menu, type...

Page 163

System ProgrammingIMl66-107Specialized Route Access (SRA) Configuration 
- continued
)ff ice Code And Area Code Tables: TheTo program office code table,
lffice code table matches a dialed office1. Type I % 7 4 6 +k and press RETURN,
odewith one of the office codes that you2. From the main menu, type 1 and press RETURN for
iave entered in the table, and routes thesystem COS menu,
all over the line group that you have3. From the system COS menu, type 16 for specialized
ntered for that office code. The area...

Page 164

IMl66-107System ProgrammingSpecialized Route Access (SRA) Configuration 
- continued
Special Area Code Tables: The fourTo assign the special area codes to the four tables,
special area code tables must first match a1. Type I 
t 7 4 6 X and press RETURN,
dialed area code and then match the dialed2. From the main menu, type 1 and press RETURN
office code with office code entries in the
for system COS menu,
matched table. With a complete match3. From the system COS menu, type 16 for specialized route
found,...

Page 165

System ProgrammingIM166-107Specialized Route Access (SRA) Configuration 
- continued
Insert Digits: You can program the
system, on a per line group basis, to insert
up to six digits before a dialed number. This
‘eature is useful if the dialed number must
match a specific format for the line group
oeing used.
Overflow Line Group: You can assign an
overflow line group that the system can
route calls over when no lines are free in
the line group assigned to the matching
entry; otherwise, the system will...

Page 166

System ProgrammingIMl66-107
Station Message Detail Accounting/Reporting Configuration
.The system produces five different call cost reports for printing. They are:
1. Detailed report of all station
2. Detailed report of all accounts
3. Trunk summary report
4. Department summary report5. All records
The system generates reports automatically for printing whenever it detects that its records storage area is 95
percent full. You can use class of service programming to choose the reports that you want the...

Page 167

IMl66-107System ProgrammingStation Message Detail Accounting/Reporting Configuration 
- continued
Press ITCM %#7463.
Station Message Detail Accounting
(MDA) Printout
Call cost reports, produced by the system
for printing, are generated automatically
whenever the system detects that the
records storage area is ninety-five percent
full. Program the system to automatically
generate these reports for printing at a
certain time each day if desired.
You can command the system to print
several different types...

Page 168

System ProgrammingIMl66-107Station Message Detail Accounting/Reporting Configuration 
- continued
Station Message Detail ReportingTo program for SMDR printout as the system collects it,
(SMDR) Printout
1. Dial 77.
Program the system for the SMDR to
2. Dial 2 .
“SMDR PRINTXXX ”
Drovide continuous printout of system-wide
3. Press Al to toggle between enable and disable
station call activity as it is collected by the
(Al LED On = Enabled)
system if desired.-OR-
- Dial 1 to enable printing.“SMDR PRINT ON ’...

Page 169

System ProgrammingIMl66-107
Toll Restriction Table Configuration
Before programming the toll restriction configuration, enter the toll restriction requirements on the toll restriction
reference tables found at the end of Chapter 4.
In order for toll restriction to take effect, the following three-fold process must occur.
B Program entries in one or more toll tables
D Assign toll tables to all appropriate lines.
D Assign toll tables to all appropriate stations.
After you program the toll tables, you must...

Page 170

IMi66-107System ProgrammingToll Restriction Table Configuration 
- continued
0 To make the programming selections, dial the feature code and then dial the configuration code (or press the
programming button where appropriate).
NOTE: A lighted LED next to the programming button for the selection indicates the current configuration.
When a sing/e button provides a toggle (on/off) action, the lighted LED indicates the active feature.
0 The first step in any programming sequence is to enter the base level....
Start reading Comdial Digital Telephone System Instructions Manual

Related Manuals for Comdial Digital Telephone System Instructions Manual

All Comdial manuals