Home > Comdial > Communications System > Comdial Digital Telephone System Instructions Manual

Comdial Digital Telephone System Instructions Manual

Here you can view all the pages of manual Comdial Digital Telephone System Instructions Manual. The Comdial manuals for Communications System are available online for free. You can easily download all the documents as PDF.

Page 171

System ProgrammingIMl66-107Toll Restriction Table Configuration 
- continued1 Press 
lTCM *#7i*.(
Assign Toll Restriction Tables To
Stations
Assign Toll Restriction Tables To
Stations For Night Transfer (of ringing)
Toll tables assigned with this feature have
an effect only when the attendant places
the telephone system in the night transfer
(of ringing) mode of operation.
Assign Toll Restriction Tables To
System Speed Dial Calls
When you enable this feature, the system
applies toll restriction tables...

Page 172

IMl66-107System ProgrammingToll Restriction Configuration 
- continued
Assign Toll Restriction Override 
(TRO)You can use the sequence of steps listed below to program a TRO
Code: The TRO feature allows users tocode from station 10.
override the toll restriction that they1. Press ITCM and dial +K # 7 4 6 +++ to enter COS
encounter at other stations with their ownprogramming,
“CONFIG. MODE”
station’s toll restriction assignments. In2. Dial 53 for station features,“STATION FEATURES”
programming for this...

Page 173

This page remains blank intentionally 

Page 174

IMl66-107System Programming
Video Display Terminal Programming Feature
You can program the class of service features from a video display terminal (VDT) instead of from the
programming station if you wish. The VDT that you use must be a serial-data, RS-232 type,
asynchronous device.
You can employ a personal computer (PC) if it will run a communications software program that allows
it to emulate a data terminal device (DTE equipment). Many effective communications sdftware
programs are available for this...

Page 175

System ProgrammingIMl66-107
Video Display Terminal Programming Procedure
Introduction
The programming procedure is menu driven.
0
0
0
0
0
A list of selections are presented for consideration
which differ in content and required response.
Each selection, when responded to, either causes a
further breakdown of selections to be presented or
causes a particular COS programming action to
take place.
This menu system prompts the programmer for the
required response and, where appropriate, will
repeat prompts...

Page 176

IM166-107System ProgrammingVideo Display Terminal Programming Procedure 
- continued
Remote Programming Configuration
You can program the digital telephone system
remotely using the following equipment:
0 VDT or a PC and appropriate software program,
0 Pair of data modems.
The data modems must be: “Hayes-compatible”,
capable of 
300-, 1200-, 2400-, or 9600-baud data
speeds, and have auto-answer capability. Be sure 
to
vetify the auto-answer capability before purchasing the
units. You are assured of best...

Page 177

System ProgrammingIMl66-107Video Display Terminal Programming Procedure 
- continued
Remote Programming Configuration 
- continued
If you are employing remote programming, the
data parameters of the PC must match the modem
connected to it. The modem connected to the
digital telephone system must match the data
parameters of it as well.
NOTE: Remember, &bit data is required for XMODEM
protocol.
If the digital telephone system is not
now programmed to provide 
&bit data, you will
have to reprogrammed it...

Page 178


				            

Page 179

System ProgrammingIMl66-107Video Display Terminal Programming Procedure 
- continued
Menu Descriptions
Main Menu Selections
C.O.S. Programming
1. System C.O.S.
2. Line C.O.S.
3. Station C.O.S.
4. Toll Restriction Table Administration
5. Information
6. Logoff
Enter Selection:
0 Selection 1: Chooses system COS programming.
0 Selection 2: Chooses line COS programming.
0 Selection 3: Chooses station COS programming.
l Selection 4: Chooses toll restriction table
administration programming.
0 Selection 5:...

Page 180

IMl66-107System ProgrammingVideo Display Terminal Programming Procedure 
- continued
Menu Descriptions 
- continued
0 Selection 3 : System timing (system timing
requirements)l
Recall / TAP Timel Pause Time
l Timed Hold Recall Time
l Transfer Recall Timel Call Park Recall Time
l Extended DTMF Dialing Tones
0 Selection 4: Load/Save COS data
0 Selection 5 : Serial communication parameters (for
data 
port A and data port B)
0 Selection 6: COS data printout
0 Selection 7: Set clock date/time.
0 Selection 8:...
Start reading Comdial Digital Telephone System Instructions Manual

Related Manuals for Comdial Digital Telephone System Instructions Manual

All Comdial manuals