Cisco D9854i Manual

 
 
 Configuring System Settings 
 
78-4021470-01 Rev J 207 
 
Viewing Alarm/Warning History 
From the user interface of the D9854, click System Settings > Alarms > History. The 
History page is displayed. 
 
The Alarm and Warning History page displays all the past system event messages 
and their set and cleared dates and times. For more information on the alarm 
messages, refer to Messages (see D9854 Receiver Alarm Messages on page 231). 
Click Clear Alarms/Warnings History to clear all existing...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
208 78-4021470-01 Rev J 
Viewing Version Information 
From the user interface of the D9854, click System Settings > Versions > Versions. 
The Versions page is displayed. 
 
The Software Versions section displays the currently running loaded application 
version number, the factory loaded application version number, and the Host Boot 
version numbers. In the Select APP Version drop-down, you can choose a different 
application version number to load. Click...

 
 
 Configuring System Settings 
 
78-4021470-01 Rev J 209 
 
Note: For application downloads, once the download is complete, the D9854 receiver 
will reboot automatically. For FPGA downloads, you must click Reboot Receiver in 
the Service Actions page (Support > Service Actions) to manually reboot the D9854 
receiver and complete the download. This is to facilitate the typical case in which the 
user intends to flash the FPGA file (no auto reboot) followed by an APP download 
(auto reboot). 
The...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
210 78-4021470-01 Rev J 
Setting up Import/Export Information 
1 From the user interface of the D9854, click System Settings > Settings File > 
Import/Export. The Import/Export page is displayed. 
 
In the Device Settings File Transfer section, you can export and/or import 
device settings and transport network information. 
2 Select Export Device Settings & Transport Network Information and click 
Export to download device settings and transport network...

 
 
 Configuring System Settings 
 
78-4021470-01 Rev J 211 
 
7 Set the FTP Server IP Address of the FTP server used to restore the 
backup/restore file. The address is up to 12 characters in length (e.g. 
171.300.100.200 and in the range from 0 to 255. 
8 Set the FTP User Name and FTP Password to access the FTP server. 
Note: The FTP Password is not retained in the receiver. You must re-enter the 
password before initiating the backup or restore operation. 
9 Set the FTP Port Number of the FTP server...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
212 78-4021470-01 Rev J 
Viewing the Backup/Restore Status 
From the user interface of the D9854, click System Settings > Settings File > Status. 
The Status page is displayed. 
 
The following table displays the Settings File Backup/Restore/Operation History 
information: 
Status  Description 
Last Backup File Name Name of the file to use. 
Backup Time Stamp Date and time of the last successful backup file saved. 
Last Restored File Name Name of the last...

 
 
 Configuring System Settings 
 
78-4021470-01 Rev J 213 
 
Managing D9854 Web GUI Accounts 
You can define up to 10 usernames/passwords for login use via web GUI session on 
the D9854 receiver.  
When a user tries to login, the user is required to provide a username and a 
password. The user is granted access only if this username/password pair exists in 
the authentication table. 
The factory preset Admin account has Admin privileges and is allowed to add new 
users, delete users, change usernames,...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
214 78-4021470-01 Rev J 
Password Complexity Description 
No Checking There are no restrictions on passwords.  
Note: A minimum of one character is required. 
Minimal Checking A password must comply with the following 
requirements: 
 It cannot contain username or reversed username. 
 It cannot contain any of the following strings: cisco, 
sciatl, ocsic, Itaics, atlsci, icslta, or any string 
achieved by full or partial capitalization of letters. 
 No...

 
 
 Configuring System Settings 
 
78-4021470-01 Rev J 215 
 
  
To Add a User Account 
Note: This feature is available to a user with Admin privileges only. 
1 From the Account Management page, click on the Manage User Logins link. The 
Login Accounts page is displayed. 
 
2 Click Add to create a new login account.  
Note: You can create a maximum of 10 user accounts. 
The Add Login Account window is displayed. 
 
3 In the Username field, enter a user ID. The new username should not match any 
of the...

 
Chapter 5    Web GUI Setup and Monitoring  
 
 
216 78-4021470-01 Rev J 
4 In the New Password field, enter a password to assign the user ID. The 
password must follow the rules configured in the Set Password Complexity for 
All Users parameter. For more information, see To Change the User Login 
Passwords (on page 213). 
5 Enter the new password again to confirm in the Confirm New Password field.  
Note: The New Password and Confirm New Password should be identical. 
6 In the Administrator Password...